science lab equipment manufacturer

Microprocessor Lab Trainers

Microprocessor Lab Trainers Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Microprocessor Lab Trainers in India,

Microprocessor Lab Trainers: 8085 and 8086

Quick answer. Two trainers here: an 8085 educational lab trainer and an 8086 educational lab trainer. Before specifying either, two things are worth knowing. First, the honest reason these architectures are still taught - they are transparent, and a student can watch a bus cycle happen on an oscilloscope, which no modern processor allows. Second, and this is where most purchases go wrong: the trainer board on its own cannot run most of the experiments in a microprocessor syllabus. The experiments live on the interfacing cards - programmable peripheral interface, timer, keyboard-display controller, interrupt controller, serial interface, analogue converters, stepper motor - and those are usually quoted separately. Ask which are included, and which bus connector they use.

Important, published rather than hidden: the code MLT- is used by three different categories on this site. In this listing MLT-0001 is an 8085 microprocessor trainer. In our microwave lab trainers listing MLT-0001 is a reflex klystron bench, and in our mechanical lab trainers listing it is an engineering maintenance trainer. Microprocessor, Microwave and Mechanical Lab Trainers all reduce to the same initials, and each category numbers from 0001. So an MLT- code does not identify a product. Order by code and full product name; we will confirm both on the quotation. It is flagged for correction as a database fix.

Why these processors are still taught

It is a fair question, and the answer is not nostalgia. These are not current products and nobody designs with them. They are taught because they are visible.

  • The instruction set is small enough to hold in your head, so a student can hand-assemble a short program and know exactly what every byte does. That is the fastest route to understanding what a processor is.
  • The bus is external and observable. Address and data lines, the address latch enable, the read and write strobes - all of it is on pins, and a student can put an oscilloscope on them and watch a machine cycle happen. On any modern processor the bus is internal, the memory is on-die and the behaviour is invisible.
  • Peripheral interfacing is explicit. Address decoding, chip select logic, memory-mapped against input-output-mapped access - the student wires it and sees why it matters. On a modern microcontroller the peripherals are already connected and configured by a library.
  • Interrupts can be traced end to end: the request line, the acknowledgement, the vector, the service routine, the return. It is the clearest demonstration of an idea that is central to every system a student will ever work on.

So the sensible position is this: teach the 8085 as a transparent model of how processors work, and teach current practice on a microcontroller board afterwards. Many syllabuses in India and elsewhere still name the 8085 and 8086 explicitly, which settles the question for those courses. If yours does not name them, we would rather you spent the money on an embedded board from our embedded lab trainers range, where the same concepts arrive with a toolchain and a debugger that students will meet in work.

What to specify on the trainer itself

  • Keypad and display, or PC-hosted, or both. A hex keypad with a seven-segment display teaches machine code, addresses and memory as physical things - the student types opcodes and sees them land. A PC-hosted assembler is faster, closer to practice and better for longer programs. Both is the right answer where the budget allows, and the keypad version is the one to keep if you must choose, because typing an opcode by hand is a lesson a cross-assembler removes.
  • The monitor program, and above all single-stepping. Ask exactly what the on-board monitor provides: examine and modify memory and registers, insert breakpoints, and execute one instruction at a time. Single-stepping is the feature that makes a microprocessor trainer teach rather than merely run - the student watches each register change as each instruction executes, and the machine stops being magic. A trainer without it is much less useful at any price.
  • Memory provided, and whether it can be expanded. Enough for the longest program in your syllabus, with headroom for projects.
  • The bus expansion connector. Note which it is, because interfacing cards from a different maker will usually not fit, and a laboratory that buys trainers from one source and cards from another often finds it owns two incompatible halves of an experiment.
  • A printed instruction set card and an experiment manual. For hand assembly the instruction summary is used constantly; if it is not supplied, print and laminate one before the first session.

The interfacing cards are the syllabus

This is the point we would most want a buyer to take from this page. A microprocessor syllabus lists experiments such as these - and each one needs hardware beyond the trainer board:

  • Parallel input and output, in each operating mode, with handshaking - needs a programmable peripheral interface card.
  • Timing, delays, square wave generation, event counting - needs a programmable timer-counter card.
  • Keyboard scanning and multiplexed display - needs a keyboard-display controller card, and it is the experiment that explains how the trainer's own front panel works.
  • Prioritised and vectored interrupts - needs an interrupt controller card.
  • Serial transmission, framing and baud rate - needs a serial interface card.
  • Analogue input and output, waveform generation, closed-loop exercises - needs converter cards.
  • Stepper motor control, traffic light sequencing, temperature control - the application experiments, each needing its own card.

So when you enquire, send us the experiment list rather than the trainer name. We will quote the trainer and the cards it needs together, state which bus connector they use, and say plainly if an experiment on your list needs something we have not included. A trainer delivered without its cards is the commonest disappointment in this part of the catalogue, and it is entirely avoidable at the quotation stage.

8085 or 8086?

The 8085 is an eight-bit processor with a simple flat address space, and it is the better first teaching machine for exactly that reason: nothing stands between the student and the bus.

The 8086 is sixteen-bit, and its teaching value is specific: segmented addressing. An address is formed from a segment register and an offset, which students find genuinely confusing on paper and which becomes clear in about twenty minutes on a trainer where they can set a segment register and watch the physical address change. It also introduces a wider data path, more addressing modes and a richer instruction set.

For a course that teaches both, buy the 8085 first and more of them, since that is where the fundamentals are learned in groups; a smaller number of 8086 trainers will serve the segmented-addressing and advanced-programming work.

What to tell us when you enquire

  • Your experiment list, as the syllabus words it - this determines the cards, which determine the price.
  • Whether you need keypad-and-display operation, PC-hosted operation, or both.
  • Whether the monitor must support single-stepping and breakpoints.
  • Whether you already own interfacing cards, and if so from which trainer family and with which bus connector.
  • How many benches are to be equipped, and the group size per bench.
  • Supply voltage and frequency, and destination country.

Related ranges: microprocessor trainer kits for the wider range under our other parent, embedded lab trainers for microcontroller work with a modern toolchain, VLSI and embedded trainers, digital electronics lab trainers for the logic that precedes this subject, and EPROM programmers. The full training kits and electronics lab trainer kits categories list the rest.

Frequently asked questions

Is it still worth teaching the 8085 in 2026?

If your syllabus names it, yes, and it teaches one thing better than any modern device: a processor you can watch. The bus is on pins, the instruction set is small enough to hand-assemble, address decoding is wired by the student, and an interrupt can be traced from request to return. Then teach current practice on a microcontroller board. If your syllabus does not name the 8085, we would rather you bought the embedded board.

Why does the trainer alone not cover our experiment list?

Because most microprocessor experiments are interfacing experiments, and the interfaces are on separate cards: parallel interface, timer, keyboard-display controller, interrupt controller, serial, converters, stepper motor. The board provides the processor, memory and monitor. Send us the experiment list and we will quote the trainer and the required cards together rather than the board on its own.

Can we use interfacing cards we already own?

Only if the bus expansion connector matches, and across makers it usually does not. Tell us which trainer family your existing cards came from and we will confirm compatibility in writing before quoting. If they are incompatible, say so early - it is cheaper to buy a matching trainer than to adapt a bus.

Keypad or PC-based - which teaches better?

The keypad teaches more, and the PC is more convenient. Entering opcodes by hand makes machine code, addresses and memory concrete in a way a cross-assembler removes, and that understanding is the point of the course. A PC-hosted assembler is better for longer programs and closer to real practice. Both together is the best arrangement; if you must choose one, keep the keypad.

What does single-stepping give us?

The whole point of the trainer. Executing one instruction at a time and reading the registers after each one lets a student see exactly what each instruction does, find their own error, and understand the fetch-execute cycle as a sequence of events rather than a diagram. Ask for it explicitly, along with breakpoints and the ability to examine and modify memory and registers.

Why does your 8085 trainer share a product code with a klystron bench?

Because product codes have been generated from category names without checking for codes already in use, and three of our categories reduce to the same initials. We have published it here rather than hiding it, and it is flagged for correction. Until then, order by code and full product name together and we will confirm both on the quotation - that removes the risk entirely.

Key takeaways

  • These processors are taught because they are visible - external bus, small instruction set, explicit interfacing, traceable interrupts.
  • The interfacing cards are the syllabus. Quote from the experiment list, not from the trainer name.
  • Insist on single-stepping with breakpoints and register examination; without it the trainer runs programs rather than teaching them.
  • Check the bus expansion connector. Cards from another maker usually will not fit.
  • Buy 8085 for the fundamentals, 8086 for segmented addressing - and more of the former than the latter.
  • An MLT- code identifies three different products on this site. Always order by code and full name.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

This page is deliberately short because the category holds two records; padding it to the length of our larger category pages would serve nobody. Notes published rather than hidden: the MLT- code collision across three categories is described above; the product names carry the padding phrase "For Vocational Training And Didactic...", which we are removing; and this category overlaps our microprocessor trainer kits listing under a different parent, which we have flagged for a structural decision. The architectural comparisons and teaching judgements on this page are our own engineering opinion offered to help a buying decision. Monitor features, memory sizes, supplied cards, bus connectors and all other specifications will be confirmed in writing on the quotation; verify them before tender submission.

8085 Microprocessor Educational Lab Trainer For Vocational Training And Didactic Labs

MLT-0001

Equipment for Education, Engineering and Vocational Training - 8085 Microprocessor Educational Lab Trainer - 8085 Microprocessor Trainer can interface with IBM PC/XT/AT computer with the help of 96 bit TTL I/O Experimental Interface and Editor Assembler Software. It is quite an efficient system based on Industry Standard Intel 8085 ìp for the purpose of training and prototype development of microprocessor based systems. Its hardware is capable of supporting multi processor configuration also. The unit is self contained and requires no other apparatus. Practical experience on this board carries great educative value for Science and Engineering Students. The Microprocessor trainer is designed to teach the subject of Microprocessor programming and interfacing through practical, essentially designed to teach the study of : Design student projects Familiarize components used in Microprocessor based instruments Study the signals generated by the Microprocessor Learn the art of programming in machine language Design application oriented equipment Design and debugging techniques, etc. Perform input / output experiments Instruction set of 8085 Hardware Specifications: CPU : 8085 Microprocessor @6.144 MHz MEMORY : Total space ON BOARD is 48KB,Comprising of 16KB monitor EPROMS and 32KB RAM. Battery Backup for RAM. No expansion required PERIPHERALS: : 8279 for controlling 24 feather keys (including 6 digit seven segment display). :1 Timer/counter with three independtly programmable counters :Two 8255 for controlling 48 I/O lines and same are brought out to FRC 50 pin connector : 8251 for RS 232 C serial communication and firmware for UP/DOWN facility for IBM PC/XT/AT computer : Built-in cassette interface : Built-in Speaker interface : Built-in EPROM programmer for 27128 operating at 12.5 INTERFACING : All buffered & demultiplexed TTL compatible signals brought on a 50 pin FRC connector including address and SIGNALS data control lines brought out at another 50 pin FRC connector. Several experimental interface modules can be connected to this trainer. They are ADC, DAC, Stepper motor, 8-bit switch input, 8-bit LED output, Relay interface module, etc. and many more are available. The following programs can be performed on the above 8085 Microprocessor Trainer, detail of which have been provided in the manual supplied with the Trainer. Experiment: Program to perform integer division 8-bit by 8-bit Program to perform integer division 16-bit by 8-bit Transfer of a block data in memory to another place in memory in the direct and reverse order Finding the parity of number Sorting of array in Ascending order Sorting of array in Descending order Program to multiply two 8-bit numbers Program to generate and sum 15 Fibonacci number Program for rolling display of message “INDIAN” To insert a number at correct place in a sorted array Program to display smallest number in an array Program to display largest number in an array Program to add 2 numbers in Hex and Decimals 4 digit Hex counter. Program for converting 8 bit binary (Hex) to Decimal Subtraction of two 16 bit numbers Program to perform Hex to BCD conversion. Program to read key board and display its code Program to find HCF Program to find LCM Software Capabilities: The Monitor provided in 32K EPROM is capable of assisting the user, entering, editing and running the programs in assembly language. Along with other keys the following keys support these features . SET ADDR : This key allows to examine and optionally update the RAM. EXAM/REG : This key allows to examine and optionally update the CPU Registers. “GO”&“EXEC” KEYS : These keys allow running of the user or monitor programs at full speed. STEP : This key allows running of the user or monitor programs, one instruction at a time Features: The unit is operative on 230V, 50 Hz A.C. Mains Strongly Supported by Detailed operating Instructions, giving details of Object, Theory, Design procedures, ReportSuggestions and Book References Weight : 5 Kg. (Approx.) Power Supply: 5V @ 1A, ± 12V @ 500mA All assembled in an well de signed cabinet Accessories: 50 pin FRC Cable 2 Nos. Software CD 1 No. 

8086 Microprocessor Educational Lab Trainer For Vocational Training And Didactic Labs

MLT-0002

Equipment for Education, Engineering and Vocational Training - 8086 Microprocessor Educational Lab Trainer - 8086 Microprocessor Trainer uses Intel 8086 is a 16-bit microprocessor as CPU. This is one step above 8085 (8-bit) microprocessor. The term “16-bit” means that its arithmetic logic unit, internal registers, and most of its instructions are designed to work with 16-bit binary words. The 8086 has a 16-bit data bus, so it can read data from or write data to memory and ports either 16 bits or 8 bits at a time. As its address bus is 20-bit wide, it can address memory up to 1,048,576 locations. Each of the 1MB locations represents bite wide. Therefore it is necessary to study by experimentation how a 8086 microprocessor responds for various conditions. Using this trainer, students studying in electronics, electrical, instrumentation, mechanical, chemical engineering subjects, B.Sc. (electronics, computers, and physics) laboratory, and polytechnics can learn programming an 8086 Microprocessor. This can be used to some extent for designing prototypes. SPECIFICATIONS CPU : 8086 Microprocessor @ 6.144 MHz MEMORY : Total space ON BOARD is 32KB, Comprising of 16KB monitor EPROMS and 16KB RAM. Battery backup for RAM PERIPHERALS : : 8279 for controlling 24 feather keys (including 7 digit seven segment display) :One 8255 for controlling 24 I/O lines and same are brought out to 50 pin FRC connector EXPERIMENT: The following programs can be performed on the above 8086 microprocessor trainer, detail of which have been provided in the manual supplied with the trainer. Program to perform 16-bit addition Program to perform 16-bit subtraction Program to perform 16-bit multiplication Program to perform 16-bit division Program to display largest no. in an array Program to display smallest no. in an array. Program to arrange numbers in ascending order Program to arrange numbers in descending order Program to determine factorial of a number Program to determine fibonacci series of a number Program to check password Program to perform scrolling display SOFTWARE CAPABILITIES The Monitor provided in 32K EPROM is capable of assisting the user, entering, editing and running the programs in assembly language. FEATURES The unit is operative on 230V, 50 Hz A.C. Mains Strongly Supported by Detailed operating Instructions, giving details of Object, Theory, Design procedures, Report Suggestions and Book References Weight : 4 Kg. (Approx.) Power Supply : ±12V @ 500mA . All assembled in an well designed cabinet ACCESSORIES: 50 pin FRC Cable 1 No.. 

Supply of Microprocessor Lab Trainers from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }