science lab equipment manufacturer

Machines

Machines Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Machines in India,

Quick answer. This listing of roughly 160 items is three laboratories sharing one name - thermodynamics and power plant, structures and strength of materials, and theory of machines and tribology - so the first decision is which laboratory you are equipping, then the one question that governs it. For thermodynamics: running unit or simulator, and what is statutory. For structures: demountable or fixed. For tribology: what is in the modular base unit and which modules can be added later. Send your syllabus experiment list with the laboratory named, and the quotation becomes short and comparable.

What is actually in this listing

This is the largest listing in the engineering apparatus group - roughly a hundred and sixty items over sixteen pages - and its name does not tell you what is in it. So here it is plainly: these are three different laboratories sharing one category. The section below is a map, and it is the fastest way to reach the right equipment.

If you are equipping...Look forExamples in this listing
A thermodynamics or power plant laboratoryPrime movers, compressors and steam plantTwo-shaft gas turbine and gas turbine simulator, single and two-stage air compressor test units and modules, single cylinder steam engine, steam boiler safety and control
A structures or strength of materials laboratoryExperimental sets for forces, equilibrium and deflectionForces in a truss, equilibrium of a rigid body, stability of structures, structures table with standard roof truss, Warren girder, three hinged arch, suspension bridge, apparatus for testing torsion and deflection, force apparatus
A theory of machines or tribology laboratoryFriction, bearings, contact and gear apparatusPrecision friction measurement, bearing friction, journal bearing pressure distribution, block on ring, pin on disc, slip stick and friction vibration, optical elastohydrodynamics, rolling sliding disc, tribology trainer modules, cam mechanism, gear assembly, Hertzian contact

And two warnings about the codes in this listing, which matter if you order by code. First, the numbering gains a digit after ninety-nine: the codes run MAC-0001 to MAC-0099 and then MAC-00100, MAC-00101 and onwards with five digits. A search for MAC-0100 will not find MAC-00100, and a sorted list puts the five-digit codes in the wrong place. Second, two records on the last page carry a different prefix entirely, and two more differ from earlier records only by a trailing digit. The fix on our side is under way; in the meantime quote the code and the full product name together and have both confirmed on the proforma invoice.

The thermodynamics group: does it run, and what is statutory?

Two questions govern this group, and both change the price by a large factor.

Running unit or simulator? The listing offers a two-shaft gas turbine and, separately, a two-shaft gas turbine simulator, and an air compressor test unit alongside compressor modules. A running gas turbine is a serious installation - fuel, air, exhaust, noise, instrumentation and a commissioning engineer - and it is the right purchase for a laboratory teaching gas turbine performance to final-year or postgraduate students. A simulator costs a fraction of that, occupies a bench, and lets a whole class explore the effect of pressure ratio, turbine inlet temperature and component efficiency in an afternoon. Neither replaces the other: the running unit teaches what a machine really does, the simulator teaches the cycle. Decide which your syllabus actually examines before comparing prices, and if the answer is both, buy the simulator first because more students will use it.

What is statutory? Anything that stores pressure or generates steam carries legal obligations in most countries. A steam boiler, even a small teaching one, is normally a registered pressure vessel subject to periodic inspection by a competent authority, and an air receiver on a compressor test unit usually is too. That is a matter of arranging registration and inspection before commissioning, not after, and it is the commonest reason a boiler trainer sits unused in a corner. Ask us for the vessel certificate, the drawings, the relief device settings and where they discharge, and put the question to your own authority with those documents in hand. The steam boiler safety and control unit is, incidentally, an excellent teaching object precisely because it demonstrates the devices that make a boiler safe - level controls, relief, and the sequence of a safe start.

For the compressors, ask for volumetric and isothermal efficiency instrumentation, the intercooler arrangement on the two-stage unit, and the receiver certification. The thermodynamic companions to this group are in the heat transfer lab range and refrigeration and air conditioning.

The structures group: demountable or fixed?

This is the single question that decides how much a structures laboratory teaches, and it is rarely in a specification.

A demountable apparatus - where students assemble the truss, arch or frame from members and joints before loading it - teaches far more than a fixed frame that is only loaded. Building the structure is where a student discovers what a pin joint does, why a redundant member changes everything, and how a load path works. A fixed frame gives a tidier set of readings in less time. For a teaching laboratory the demountable version is usually worth the extra session it costs; for a demonstration bench the fixed version is fine.

Then the measurement, because that is the other half. Ask: how are member forces measured - spring balances, load cells with a digital indicator, or strain gauges with a bridge; how are deflections measured, and what resolution; and is the apparatus pre-calibrated with the member forces readable directly, or must the student calculate them? Ask also what loads are supplied, since a structures rig without its set of hangers and weights is incomplete, and weights are heavy, awkward to ship and easy to leave off a quotation.

For the torsion and deflection apparatus, ask the specimen sizes and materials supplied - the classic exercise compares steel, brass and aluminium of the same geometry, and it is worth asking for the set rather than one material. Materials testing proper, with load frames and verification certificates, is in universal testing machines and tensile testing machines; the structures apparatus here is about forces in assemblies rather than the strength of a material.

The tribology group, which is the unusual part of this listing

Few teaching catalogues carry a tribology set, and this one does: a basic module with experimental modules for block on ring, pin on disc, journal bearing pressure distribution, slip stick and friction vibration, rolling and sliding discs, and optical elastohydrodynamics. If you teach lubrication, wear or machine design, this is the most interesting equipment on the page, and it is worth knowing what each module shows.

Block on ring and pin on disc are the two standard wear geometries, and they produce a wear rate and a friction coefficient under a controlled load and speed - the numbers a machine designer actually uses. Ask what loads and speeds the base unit covers, how wear is measured (mass loss, scar width or displacement) and what specimens are supplied.

Journal bearing pressure distribution maps the pressure around and along a loaded bearing, and it is the experiment that makes hydrodynamic lubrication theory visible. As with the version in our theory of machines listing, the oil grade and the oil temperature are part of the result, because viscosity is strongly temperature-dependent; ask whether temperature is measured at the bearing.

Slip stick and friction vibration demonstrates the mechanism behind brake squeal, machine chatter and the stick-slip judder of a sticky slide - a phenomenon students meet constantly in practice and almost never in a lecture. Optical elastohydrodynamics is the most striking of the set: an interference image of the lubricant film in a rolling contact, which lets a student see a film a fraction of a micrometre thick. Ask what magnification and imaging arrangement are included and whether images can be captured, because the image is the result.

Because the set is modular, ask the question that governs a modular purchase: what exactly is in the base unit, which modules can be added later, and is the base specification likely to remain available? A modular rig is excellent value when modules can be added over several budget years and a liability if the base is discontinued.

Safety across the three groups

Each group brings its own hazard, and they are different enough to list separately. Thermodynamics: pressure and steam - relief devices, statutory inspection, hot surfaces, and the rule that a steam leak is invisible for its first few centimetres. Structures: stored energy in a loaded member and falling weights - ask about catch trays, and remember that a slender member failing in compression buckles suddenly. Tribology and rotating rigs: exposed rotating specimens, hot contacts and oil - ask for guarding, a stop within reach and a drip tray. In all three, ask for the bolt-down requirement, because a rig that moves under load is both a safety problem and a source of bad data.

What to ask for on the quotation

For every item: which of the three laboratories it belongs to and the experiments it is designed to deliver; the quantities measured and how each is read, with range and resolution; whether the apparatus is demountable; what specimens, members, weights, hangers and accessories are included, and the price of the sets that are not; services required - power, fuel, air, water, drain, extraction; whether any pressure vessel or steam generator is involved and what certification comes with it; guarding, stops and bolt-down; mass, footprint and floor loading; data logging options and software licence terms; consumables and spares with prices; and the warranty, commissioning, training and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you tender on it.

Related ranges: models for theory of machines for balancing, gyroscope, governor and cam analysis rigs, engineering training models for gear and mechanism models, heat transfer lab apparatus, civil engineering lab equipments for soils, concrete and surveying, and cutaways models for engine test rigs. The full set is listed under engineering apparatus. For a quotation, tell us which of the three laboratories you are equipping, your syllabus experiment list, the destination country and the class size in one practical session - with a listing this large, the experiment list is what makes a quotation short.

Frequently asked questions

Should we buy the two-shaft gas turbine or the gas turbine simulator?

Decide which your syllabus examines. A running gas turbine is a serious installation - fuel, air, exhaust, noise, instrumentation and a commissioning engineer - and suits a laboratory teaching gas turbine performance to final-year or postgraduate students. The simulator occupies a bench and lets a whole class explore pressure ratio, turbine inlet temperature and component efficiency in an afternoon, at a fraction of the cost. The running unit teaches what a machine really does; the simulator teaches the cycle. If the answer is both, buy the simulator first, because more students will use it.

Does a teaching steam boiler or air compressor need registration?

In most countries, yes. Anything that stores pressure or generates steam carries legal obligations: a steam boiler, even a small teaching one, is normally a registered pressure vessel subject to periodic inspection by a competent authority, and an air receiver on a compressor test unit usually is too. Arrange registration and inspection before commissioning - it is the commonest reason a boiler trainer sits unused. Ask us for the vessel drawings, the relief device settings and where they discharge, and contact us for the latest copies of the relevant certificates, then take those documents to your own authority.

Are demountable or fixed structures apparatus better for teaching?

For a teaching laboratory, demountable is usually worth the extra session it costs. When students assemble the truss, arch or frame from members and joints before loading it, they discover what a pin joint does, why a redundant member changes everything and how a load path works. A fixed frame gives a tidier set of readings in less time and is fine for a demonstration bench. Then ask how member forces are measured - spring balances, load cells or strain gauges - how deflections are measured and to what resolution, and whether the full set of hangers and weights is included.

What do the tribology modules actually show?

Block on ring and pin on disc are the two standard wear geometries, producing a wear rate and a friction coefficient under controlled load and speed - the numbers a machine designer uses; ask the loads and speeds the base unit covers and how wear is measured. Journal bearing pressure distribution makes hydrodynamic lubrication visible; ask whether temperature is measured at the bearing, since viscosity depends on it. Slip stick and friction vibration shows the mechanism behind brake squeal and machine chatter. Optical elastohydrodynamics images a lubricant film a fraction of a micrometre thick; ask the magnification and whether images can be captured.

Is the modular tribology trainer a safe long-term purchase?

It is excellent value when modules can be added over several budget years, and a liability if the base unit is discontinued. So ask what exactly is in the base unit, which modules can be added later, and whether the base specification is likely to remain available. Few teaching catalogues carry a tribology set at all, so for a department teaching lubrication, wear or machine design it is the most interesting equipment on the page - but have the module list, the specimens supplied and the imaging arrangement for the elastohydrodynamics module confirmed in writing on the quotation.

What safety provisions does each group need?

Each brings a different hazard. Thermodynamics: pressure and steam - relief devices, statutory inspection, hot surfaces, and the rule that a steam leak is invisible for its first few centimetres. Structures: stored energy in a loaded member and falling weights - ask about catch trays, and remember that a slender member failing in compression buckles suddenly. Tribology and rotating rigs: exposed rotating specimens, hot contacts and oil - ask for guarding, a stop within reach and a drip tray. In all three, ask the bolt-down requirement, because a rig that moves under load is a safety problem and a source of bad data.

Key takeaways

  • Three laboratories, one listing - name the laboratory and send the syllabus experiment list.
  • Simulator first if you need both - more students use it; the running gas turbine teaches the real machine.
  • Register pressure vessels before commissioning - boilers and air receivers usually need statutory inspection.
  • Demountable structures teach more than fixed frames; confirm hangers and weights are on the quotation.
  • Ask for the full specimen set on the torsion and deflection apparatus - steel, brass and aluminium of the same geometry.
  • Search both code formats - after MAC-0099 the codes run MAC-00100 onwards, so MAC-0100 will not be found.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Specifications - quantities measured with range and resolution, specimens, members, weights and accessories supplied, services, pressure vessel details, guarding and bolt-down, and data logging - are confirmed in writing on the quotation. For pressure vessel, calibration or other certificates, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing notes: the category name does not describe its three distinct laboratories; the numbering gains a digit after MAC-0099 (MAC-00100 onwards), so searches and sorting go wrong; two records on the last page carry a different prefix entirely; and two more differ from earlier records only by a trailing digit.

Basic Roof Truss 2

MAC-0021

Specialized Description Using this benchtop unit, the determination of powers and examination of the dissemination of powers in straightforward structures can be illustrated. The unit involves three individuals that are consolidated utilizing circles with the end goal that the joints are allowed to move. One of the individuals is accessible in three unique lengths with the goal that the point between the individuals can be balanced. The individuals participate in the plates utilizing snap activity associations. Two of the plates likewise shape the direction and are cinched to the solid base edge made of aluminum segment. One of the plates is planned as a self-adjusting support. A weight bearer is held tight the structure to give a characterized stack. The powers are estimated utilizing mechanical dislodging measures associated with leaf springs, these are fitted amidst the individuals.

Friction on Inclined Plane

MAC-0022

Specialized Description This unit empowers analyses to be performed on weight and grinding powers on a slanted plane as a component of the edge of slant. The unit contains a plane with a plastic covering, a column and a base plate. The slant edge can be balanced utilizing swiveling joint and scale over a scope of ±45°. Two sliding bodies each made of two distinct materials (steel, metal, aluminum and polypropylene) give, in mix with the plane, reproducible estimations with low "slip-stick" impacts. Subsequently, it is conceivable to obviously show the progress from static to sliding, and to unmistakably exhibit the "friction cone"

Steam Power Plant

MAC-0023

Specialized Description The uncommonly intended for specialized preparing in the zone of energy plant building, and power motors and machines, and accordingly offers various trials. An oil-warmed prompt evaporator creates wet steam, a superheater gives superheated steam. The turbine is stacked with a generator, the vitality produced is come back to the power mains. After the turbine, the steam is dense and nourished back to the evaporator. Every single applicable parameter are estimated utilizing sensors and transducers and showed on a plainly laid out switch board as estimated esteems. The switch board contains an obviously laid out stream outline for the framework. Information from the electronic estimating instruments can be exchanged straightforwardly to a PC for additionally preparing. The framework is checked and controlled utilizing a PLC.1 A fuel tank and bolster water tank are coordinated into the framework to shape an independent unit. The bolster water circuit is outfitted with an entire sustain water treatment unit that involves a recovering particle exchanger and compound metering. The framework is provided with thorough documentation. It has been worked as per legitimate wellbeing prerequisites and incorporates the stipulated security gadgets. Because of the use of a prompt heater, quick age of steam is conceivable (t approx. 5min). The kettle is type affirmed and does not require particular consent for task as indicated by German regulations.1 A supply of three-stage mains power and cooling water (10m³/h), or the cooling tower, are required for activity..

Experimental Set Equilibrium of a Rigid Body 2

MAC-0024

Specialized Description In mix with theuniversal testing outline, the conditions of balance and response powers in a stepping stool are explored with this test set. The step comprises of two parallel bars that are upheld on the all inclusive testing outline. The response powers are recreated the suitable way utilizing lines. Suspended weights speak to the powers. A weight can be situated on the stepping stool; the situation of this weight can be correctly characterized utilizing a ruler with a millimeter scale. Because of its heartiness and size, the trial set can be utilized both for understudy tests and for exhibits in expansive address theaters..

Precision Friction Measurement Apparatus 2

MAC-0025

Specialized Description The accuracy estimating unit is utilized to decide coefficients of rubbing tentatively. A few distinct sets of materials with shifting surface completions can be examined. Amid this procedure, the example under examination is stationary and the supporting rubbing surface is pulled past it. Thusly a steady power estimation is made over the estimating range 02N with a determination of 0.05N. The power dial check is furnished with an air damper to remunerate slip-slap impacts to an expansive degree. The supporting rubbing surface is driven utilizing an electrical synchronous engine. The drive gives two consistent velocities. The ordinary power can be changed by including weights. The sturdybenchtop unit was uniquely outlined as an understudy analyze..

Steam Generator Module

MAC-0027

Specialized Description The benchtop unit is proposed for task together with the steam turbine, however can likewise be worked freely. The unit involves a gas warmed heater with superheater, condenser with departure unit, condensate and sustain water pump, wellbeing gadgets and instrumentation including a fumes gas analyser. The prompt kettle framework conveys steam following a couple of minutes, worst case scenario. 8kg/h at 10bar and 225°C. The cyclic procedure is anything but difficult to take after and comprehend as all segments are plainly orchestrated on the front board. Every single estimated esteem are shown both on the front board and on a PC by means of the information procurement framework gave as standard. It is additionally conceivable to get ready outlines or diagrams from estimations with the provided programming. The steam generator is composed as per the German "Technische Regeln Dampf" (TRD) (Technical Regulations for Steam). It is weight tried and has all the stipulated security fittings. A supply of mains power, water and propane or petroleum gas is required..

Friction Measurement Apparatus

MAC-0028

Specialized Description This thing of estimating gear is utilized to decide coefficients of erosion tentatively. A few distinct sets of materials with differing surface completions can be explored. Amid this procedure, the example under examination is stationary and the supporting rubbing surface is pulled past it. This outcomes in a steady, simple to peruse constrain estimation. The estimating range is between 02N with 0.1N determination. The power check has an especially simple to peruse to scale with the goal that it can be perused from a separation. An electrical synchronous engine drives the supporting grinding surface. The drive gives two steady speeds. The ordinary power can be balanced by including weights. The sturdybenchtop unit was extraordinarily planned as an understudy analyze..

Experimental Set Portal Frame

MAC-0029

Specialized Description The set is proposed for use with the general test outline and demonstratesthe versatile twisting of stacked edges. The test examples are a U-molded and S-formed casing made of steel with a square cross-segment. These are subjected to fluctuating burdens utilizing sets of weights and the subsequent disfigurement estimated. For this reason, the set incorporates two exactness position estimation measures. The direction can be either settled or free empowering the edges to be assessed as statically characterized or indistinct frameworks. The trial set-up is rapidly and safely amassed utilizing uncommon clasps..

Friction on Inclined Plane 2

MAC-0030

Specialized Description This unit empowers investigations to be performed on weight and grating powers on a slanted plane as a component of the point of slant. The unit involves a plane with a plastic covering, a column and a base plate. The slant point can be balanced utilizing swiveling joint and scale over a scope of ±45°. Two sliding bodies each made of two distinct materials (steel, metal, aluminum and polypropylene) give, in blend with the plane, reproducible estimations with low "slip-stick" impacts. Thus, it is conceivable to obviously show the change from static to sliding, and to plainly exhibit the "friction cone"

Experimental Set Influence Line

MAC-0031

Specialized Description This trial set is for use with the all inclusive test outline. With the guide of this set, the impact lines on the orientation on a three section pillar under a moving burden can be researched. Furthermore, the response powers can be figured under static load. Stacking is performed utilizing weights as a point or circulated load, or utilizing a carriage as a moving burden. The progressions under load can be unmistakably observed. The response powers are demonstrated straightforwardly on dynamometers in the bearing backings. The test set contains all the fundamental individual parts, these are connected to the separate casing utilizing quick activity clasps..

Supply of Machines from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }