science lab equipment manufacturer

Machines

Machines Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Machines in India,

Quick answer. This listing of roughly 160 items is three laboratories sharing one name - thermodynamics and power plant, structures and strength of materials, and theory of machines and tribology - so the first decision is which laboratory you are equipping, then the one question that governs it. For thermodynamics: running unit or simulator, and what is statutory. For structures: demountable or fixed. For tribology: what is in the modular base unit and which modules can be added later. Send your syllabus experiment list with the laboratory named, and the quotation becomes short and comparable.

What is actually in this listing

This is the largest listing in the engineering apparatus group - roughly a hundred and sixty items over sixteen pages - and its name does not tell you what is in it. So here it is plainly: these are three different laboratories sharing one category. The section below is a map, and it is the fastest way to reach the right equipment.

If you are equipping...Look forExamples in this listing
A thermodynamics or power plant laboratoryPrime movers, compressors and steam plantTwo-shaft gas turbine and gas turbine simulator, single and two-stage air compressor test units and modules, single cylinder steam engine, steam boiler safety and control
A structures or strength of materials laboratoryExperimental sets for forces, equilibrium and deflectionForces in a truss, equilibrium of a rigid body, stability of structures, structures table with standard roof truss, Warren girder, three hinged arch, suspension bridge, apparatus for testing torsion and deflection, force apparatus
A theory of machines or tribology laboratoryFriction, bearings, contact and gear apparatusPrecision friction measurement, bearing friction, journal bearing pressure distribution, block on ring, pin on disc, slip stick and friction vibration, optical elastohydrodynamics, rolling sliding disc, tribology trainer modules, cam mechanism, gear assembly, Hertzian contact

And two warnings about the codes in this listing, which matter if you order by code. First, the numbering gains a digit after ninety-nine: the codes run MAC-0001 to MAC-0099 and then MAC-00100, MAC-00101 and onwards with five digits. A search for MAC-0100 will not find MAC-00100, and a sorted list puts the five-digit codes in the wrong place. Second, two records on the last page carry a different prefix entirely, and two more differ from earlier records only by a trailing digit. The fix on our side is under way; in the meantime quote the code and the full product name together and have both confirmed on the proforma invoice.

The thermodynamics group: does it run, and what is statutory?

Two questions govern this group, and both change the price by a large factor.

Running unit or simulator? The listing offers a two-shaft gas turbine and, separately, a two-shaft gas turbine simulator, and an air compressor test unit alongside compressor modules. A running gas turbine is a serious installation - fuel, air, exhaust, noise, instrumentation and a commissioning engineer - and it is the right purchase for a laboratory teaching gas turbine performance to final-year or postgraduate students. A simulator costs a fraction of that, occupies a bench, and lets a whole class explore the effect of pressure ratio, turbine inlet temperature and component efficiency in an afternoon. Neither replaces the other: the running unit teaches what a machine really does, the simulator teaches the cycle. Decide which your syllabus actually examines before comparing prices, and if the answer is both, buy the simulator first because more students will use it.

What is statutory? Anything that stores pressure or generates steam carries legal obligations in most countries. A steam boiler, even a small teaching one, is normally a registered pressure vessel subject to periodic inspection by a competent authority, and an air receiver on a compressor test unit usually is too. That is a matter of arranging registration and inspection before commissioning, not after, and it is the commonest reason a boiler trainer sits unused in a corner. Ask us for the vessel certificate, the drawings, the relief device settings and where they discharge, and put the question to your own authority with those documents in hand. The steam boiler safety and control unit is, incidentally, an excellent teaching object precisely because it demonstrates the devices that make a boiler safe - level controls, relief, and the sequence of a safe start.

For the compressors, ask for volumetric and isothermal efficiency instrumentation, the intercooler arrangement on the two-stage unit, and the receiver certification. The thermodynamic companions to this group are in the heat transfer lab range and refrigeration and air conditioning.

The structures group: demountable or fixed?

This is the single question that decides how much a structures laboratory teaches, and it is rarely in a specification.

A demountable apparatus - where students assemble the truss, arch or frame from members and joints before loading it - teaches far more than a fixed frame that is only loaded. Building the structure is where a student discovers what a pin joint does, why a redundant member changes everything, and how a load path works. A fixed frame gives a tidier set of readings in less time. For a teaching laboratory the demountable version is usually worth the extra session it costs; for a demonstration bench the fixed version is fine.

Then the measurement, because that is the other half. Ask: how are member forces measured - spring balances, load cells with a digital indicator, or strain gauges with a bridge; how are deflections measured, and what resolution; and is the apparatus pre-calibrated with the member forces readable directly, or must the student calculate them? Ask also what loads are supplied, since a structures rig without its set of hangers and weights is incomplete, and weights are heavy, awkward to ship and easy to leave off a quotation.

For the torsion and deflection apparatus, ask the specimen sizes and materials supplied - the classic exercise compares steel, brass and aluminium of the same geometry, and it is worth asking for the set rather than one material. Materials testing proper, with load frames and verification certificates, is in universal testing machines and tensile testing machines; the structures apparatus here is about forces in assemblies rather than the strength of a material.

The tribology group, which is the unusual part of this listing

Few teaching catalogues carry a tribology set, and this one does: a basic module with experimental modules for block on ring, pin on disc, journal bearing pressure distribution, slip stick and friction vibration, rolling and sliding discs, and optical elastohydrodynamics. If you teach lubrication, wear or machine design, this is the most interesting equipment on the page, and it is worth knowing what each module shows.

Block on ring and pin on disc are the two standard wear geometries, and they produce a wear rate and a friction coefficient under a controlled load and speed - the numbers a machine designer actually uses. Ask what loads and speeds the base unit covers, how wear is measured (mass loss, scar width or displacement) and what specimens are supplied.

Journal bearing pressure distribution maps the pressure around and along a loaded bearing, and it is the experiment that makes hydrodynamic lubrication theory visible. As with the version in our theory of machines listing, the oil grade and the oil temperature are part of the result, because viscosity is strongly temperature-dependent; ask whether temperature is measured at the bearing.

Slip stick and friction vibration demonstrates the mechanism behind brake squeal, machine chatter and the stick-slip judder of a sticky slide - a phenomenon students meet constantly in practice and almost never in a lecture. Optical elastohydrodynamics is the most striking of the set: an interference image of the lubricant film in a rolling contact, which lets a student see a film a fraction of a micrometre thick. Ask what magnification and imaging arrangement are included and whether images can be captured, because the image is the result.

Because the set is modular, ask the question that governs a modular purchase: what exactly is in the base unit, which modules can be added later, and is the base specification likely to remain available? A modular rig is excellent value when modules can be added over several budget years and a liability if the base is discontinued.

Safety across the three groups

Each group brings its own hazard, and they are different enough to list separately. Thermodynamics: pressure and steam - relief devices, statutory inspection, hot surfaces, and the rule that a steam leak is invisible for its first few centimetres. Structures: stored energy in a loaded member and falling weights - ask about catch trays, and remember that a slender member failing in compression buckles suddenly. Tribology and rotating rigs: exposed rotating specimens, hot contacts and oil - ask for guarding, a stop within reach and a drip tray. In all three, ask for the bolt-down requirement, because a rig that moves under load is both a safety problem and a source of bad data.

What to ask for on the quotation

For every item: which of the three laboratories it belongs to and the experiments it is designed to deliver; the quantities measured and how each is read, with range and resolution; whether the apparatus is demountable; what specimens, members, weights, hangers and accessories are included, and the price of the sets that are not; services required - power, fuel, air, water, drain, extraction; whether any pressure vessel or steam generator is involved and what certification comes with it; guarding, stops and bolt-down; mass, footprint and floor loading; data logging options and software licence terms; consumables and spares with prices; and the warranty, commissioning, training and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you tender on it.

Related ranges: models for theory of machines for balancing, gyroscope, governor and cam analysis rigs, engineering training models for gear and mechanism models, heat transfer lab apparatus, civil engineering lab equipments for soils, concrete and surveying, and cutaways models for engine test rigs. The full set is listed under engineering apparatus. For a quotation, tell us which of the three laboratories you are equipping, your syllabus experiment list, the destination country and the class size in one practical session - with a listing this large, the experiment list is what makes a quotation short.

Frequently asked questions

Should we buy the two-shaft gas turbine or the gas turbine simulator?

Decide which your syllabus examines. A running gas turbine is a serious installation - fuel, air, exhaust, noise, instrumentation and a commissioning engineer - and suits a laboratory teaching gas turbine performance to final-year or postgraduate students. The simulator occupies a bench and lets a whole class explore pressure ratio, turbine inlet temperature and component efficiency in an afternoon, at a fraction of the cost. The running unit teaches what a machine really does; the simulator teaches the cycle. If the answer is both, buy the simulator first, because more students will use it.

Does a teaching steam boiler or air compressor need registration?

In most countries, yes. Anything that stores pressure or generates steam carries legal obligations: a steam boiler, even a small teaching one, is normally a registered pressure vessel subject to periodic inspection by a competent authority, and an air receiver on a compressor test unit usually is too. Arrange registration and inspection before commissioning - it is the commonest reason a boiler trainer sits unused. Ask us for the vessel drawings, the relief device settings and where they discharge, and contact us for the latest copies of the relevant certificates, then take those documents to your own authority.

Are demountable or fixed structures apparatus better for teaching?

For a teaching laboratory, demountable is usually worth the extra session it costs. When students assemble the truss, arch or frame from members and joints before loading it, they discover what a pin joint does, why a redundant member changes everything and how a load path works. A fixed frame gives a tidier set of readings in less time and is fine for a demonstration bench. Then ask how member forces are measured - spring balances, load cells or strain gauges - how deflections are measured and to what resolution, and whether the full set of hangers and weights is included.

What do the tribology modules actually show?

Block on ring and pin on disc are the two standard wear geometries, producing a wear rate and a friction coefficient under controlled load and speed - the numbers a machine designer uses; ask the loads and speeds the base unit covers and how wear is measured. Journal bearing pressure distribution makes hydrodynamic lubrication visible; ask whether temperature is measured at the bearing, since viscosity depends on it. Slip stick and friction vibration shows the mechanism behind brake squeal and machine chatter. Optical elastohydrodynamics images a lubricant film a fraction of a micrometre thick; ask the magnification and whether images can be captured.

Is the modular tribology trainer a safe long-term purchase?

It is excellent value when modules can be added over several budget years, and a liability if the base unit is discontinued. So ask what exactly is in the base unit, which modules can be added later, and whether the base specification is likely to remain available. Few teaching catalogues carry a tribology set at all, so for a department teaching lubrication, wear or machine design it is the most interesting equipment on the page - but have the module list, the specimens supplied and the imaging arrangement for the elastohydrodynamics module confirmed in writing on the quotation.

What safety provisions does each group need?

Each brings a different hazard. Thermodynamics: pressure and steam - relief devices, statutory inspection, hot surfaces, and the rule that a steam leak is invisible for its first few centimetres. Structures: stored energy in a loaded member and falling weights - ask about catch trays, and remember that a slender member failing in compression buckles suddenly. Tribology and rotating rigs: exposed rotating specimens, hot contacts and oil - ask for guarding, a stop within reach and a drip tray. In all three, ask the bolt-down requirement, because a rig that moves under load is a safety problem and a source of bad data.

Key takeaways

  • Three laboratories, one listing - name the laboratory and send the syllabus experiment list.
  • Simulator first if you need both - more students use it; the running gas turbine teaches the real machine.
  • Register pressure vessels before commissioning - boilers and air receivers usually need statutory inspection.
  • Demountable structures teach more than fixed frames; confirm hangers and weights are on the quotation.
  • Ask for the full specimen set on the torsion and deflection apparatus - steel, brass and aluminium of the same geometry.
  • Search both code formats - after MAC-0099 the codes run MAC-00100 onwards, so MAC-0100 will not be found.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Specifications - quantities measured with range and resolution, specimens, members, weights and accessories supplied, services, pressure vessel details, guarding and bolt-down, and data logging - are confirmed in writing on the quotation. For pressure vessel, calibration or other certificates, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing notes: the category name does not describe its three distinct laboratories; the numbering gains a digit after MAC-0099 (MAC-00100 onwards), so searches and sorting go wrong; two records on the last page carry a different prefix entirely; and two more differ from earlier records only by a trailing digit.

Cutaway Model Mitre Gear

MAC-00116

Specialized Description The range comprises of a progression of various cutaway models of drive framework components.All parts are mechanically important and have been arranged with the end goal that individual dynamic components are obviously noticeable to the client. The mechanical usefulness of all segments is held in full. Every one of the cutaway models is safely mounted on a base plate to which handles are appended for conveying purposes. All components are hand-driven..

Cutaway Model Mitre Gear 2

MAC-00117

Specialized Description The range comprises of a progression of various cutaway models of drive framework components.All segments are mechanically applicable and have been arranged with the end goal that individual dynamic components are plainly unmistakable to the client. The mechanical usefulness of all segments is held in full. Every one of the cutaway models is safely mounted on a base plate to which handles are appended for conveying purposes. All systems are hand-driven.

Cutaway Model Worm Gear

MAC-00118

Specialized Description The range comprises of a progression of various cutaway models of drive framework components.All parts are modernly pertinent and have been arranged with the end goal that individual dynamic components are unmistakably noticeable to the client. The mechanical usefulness of all segments is held in full. Every one of the cutaway models is safely mounted on a base plate to which handles are joined for conveying purposes. All components are hand-driven.

Critical Speed Investigation Apparatus

MAC-00119

Specialized Description Thisbenchtop unit is utilized to demonstrate the reverberation and basic bowing rate on turning shafts. The development of the rotor of a thin, adaptable shaft and unbending weights encourages the hypothetical appreciation. The rotor is hung on the base casing with turning heading. The weights and course can be put at any area along the pole and connected safely with snappy acting clips. It is driven by an adaptable coupling. Two engine velocities can be fine-balanced and preset with ten-speed potentiometers. They are controlled electronically and shown carefully. It is conceivable to switch speeds amid the examination as wanted. A straightforward defensive hood covers the turning parts. An arrangement of electrical vibration sensors with bracing set is additionally accessible..

Balance of Reciprocating Masses

MAC-00120

Specialized Description Using thebenchtop demonstrate, mass powers can be explored on a responding cylinder machine. The model has four cylinders with plastic sleeves that don't require oil. The fourfold turned crankshaft is driven by an electronically commutated DC engine through a toothed belt. The rotational speed is controlled and shown carefully. Powers and minutes are estimated utilizing strain measures on the flexible blast of the model mounting section. Every single electrical capacity are incorporated into the control unit that additionally gives a simple yield to an oscilloscope. The wrench balance for every chamber can be persistently balanced, as a guide marks are given at 90°, 180° and 270°. The common frequencies are characterized to such an extent that thunderous motions are anything but difficult to distinguish even without instrumentation..

Torsional Vibration Apparatus

MAC-00121

Specialized Description This table unit is utilized to clarify torsion and torsional vibration in tests. Exhibits and understudy tests are both anticipated in rise to measures. The center of the examination is a metal torsion bar. With the guide of hurls, mass circles of differing idleness can be joined to the bar. It along these lines it is conceivable to gather torsional vibrator frameworks with up to three masses. Vibrations can be prompted on the framework utilizing an electrical exciter provided from the control unit. A movable damper can be utilized to impact the vibrations. Shaft encoders on the hurls give the sufficiency of vibration as an electrical flag. The control unit conditions these signs and makes them accessible, e.g., for show on an oscilloscope (which must be given) or on the PC information obtaining framework. (accessible as an adornment)

Cutaway Model Multistage Gear Combination

MAC-00122

Specialized Description The range comprises of a progression of various cutaway models of drive framework components.All segments are mechanically relevantandhave been arranged with the end goal that individual activeelements are unmistakably noticeable to the client. The mechanical usefulness of all parts is held in full. Every one of the cutaway models is safely mounted on a base plate to which handles are connected for conveying purposes. All components are hand-driven.

Sensor Supply Module

MAC-00123

Specialized Description The sensor supply module is utilized to give energy to vibrations sensors. The module gives the fundamental power and yields the relating estimated signals. Up to four sensors can be associated at the same time utilizing 7-shaft DIN attachments. The simple estimated motions in the range from 1to 9 Volts are yield on 4mm research facility attachments and can be shown on a meter or an oscilloscope. Thebenchtop unit has a hearty steel sheet lodging with hostile to slip elastic feet..

Free and Forced Vibration Apparatus

MAC-00124

Specialized Description This trial on vibration is of a table-top outline. All exploratory set-ups are quickly and safely amassed on a twofold profile outline made of aluminum utilizing opening nuts and clipping levers. The vibrator comprises of a bar mounted in metal rollers toward one side; a helical spring is held tight the opposite end of the shaft. The connection of springs, the exciter and a damper to a punctured board allows an extensive variety of various set-ups to be recreated. Either an unbalance exciter or a removal exciter create vibrations; the recurrence of the vibrations can be balanced utilizing the electronic control unit. The removal exciter can be fitted straightforwardly to the base of the spring. The vibrations can be damped utilizing the movable thickness damper. To record vibration forms after some time, a mechanical drum plotter is incorporated. The trial likewise incorporates a sufficiency contact with a TTL yield, e.g. for activating stroboscopes. The outer PC helped PC information procurement and a training set for torsional vibrations are accessible as adornments

Vibration of Spiral Spring Apparatus

MAC-00125

Specialized Description A winding spring made of cool moved steel is clasped between a metal ball mounted shaft and a settled section. Two levers are fitted to the pole oppositely inverse each other. Two sliding weights of metal on the levers can be safely settled in position utilizing bracing screws. These shape the pivoting mass with a customizable snapshot of dormancy. The framework is dislodged by hand. The point of turn is perused off on a 1°scale circle that is likewise joined to the pole. The unit is expected for divider mounting..

Supply of Machines from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }