Quick answer. Buy a universal testing machine as three purchases in one: frame, fixtures and feedback. The frame is electromechanical for fine control at low loads or servo-hydraulic for large forces and cyclic work; the fixtures - grips, platens, bend rigs, compression cages, shear jigs - are what actually run your standards; and the feedback is the load cell's accuracy over its valid range plus an extensometer, because crosshead travel is not specimen strain. Buyers routinely specify only the frame. Ask for a fixture list written against your standards, and check the load cell is accurate at your lowest expected load, not just at headline capacity.
Twenty records. Most are universal testing machines in several tiers - computerised, digital, servo, servo-hydraulic, computer-controlled electronic and a servo series - together with a tensile machine with an electronic display and a set of extensometers. Four of the records are named only as a version, such as a hydraulic computerised version, which tells you nothing on its own, so ask for the specification sheet of any record whose name does not include a capacity and a frame type.
Three records in this listing are not universal testing machines at all, and two of them are the reason people arrive here. A Rockwell hardness testing machine and a computerised Brinell hardness testing machine are filed here rather than in the hardness testing machines listing, which is where a buyer would look for them - so if you came for a metal hardness tester, they are UTM-0007 and UTM-0012 and we can quote them straight away. An ultrasonic flaw detector is also here; it is a non-destructive testing instrument and belongs with that range. A digital impact testing machine and an Erichsen cupping tester are related mechanical testers rather than universal frames, and both are covered below.
A universal testing machine is three purchases in one, and buyers routinely specify the first and leave the other two to chance. The result is a good frame that cannot run the standards it was bought for.
| What you are choosing | The mistake to avoid | |
|---|---|---|
| Frame | Electromechanical, driven by screws, or servo-hydraulic, driven by a power pack. Plus capacity, vertical space and throat depth | Choosing the wrong principle. Electromechanical frames give finer control and better resolution at low loads; servo-hydraulic frames give large forces in a compact frame and handle cyclic work. A machine chosen the wrong way round performs poorly at both ends |
| Fixtures | Tension grips, compression platens, three and four point bend rigs, compression cages, shear jigs, and any specimen-specific holders your standards name | Accepting the words "with standard accessories". The fixtures are the application, and a frame without the right fixture cannot run the test at all. Ask for a fixture list written against your standards, with prices |
| Feedback | Load cell capacity and accuracy class, control modes, and strain measurement by extensometer rather than from crosshead travel | Assuming crosshead movement is specimen strain. It is not: it includes the whole load train and any grip slip, so a modulus calculated from crosshead travel is wrong |
Accuracy on a testing machine is normally quoted as a percentage of the reading, valid down to a stated fraction of capacity; below that fraction the machine is simply not specified. So a frame sized for reinforcing bar cannot certify a result on a plastic film or a yarn, however impressive its headline capacity. If your materials span orders of magnitude, the honest answers are interchangeable load cells on one frame, or two machines - a large frame for metals and concrete and a small one for polymers, paper and textiles. Ask us to quote both ways and compare.
There is also a document to ask for, and it is the one an auditor or a customer will want. There is an international standard for the verification of the force-measuring system of a static uniaxial testing machine, and it defines accuracy classes. Ask which class the machine is verified to, for the verification certificate itself, over what range of force the verification is valid, and what a local re-verification costs and takes. A calibration sticker is not the same thing.
For hydraulic frames, add: the power pack rating, noise, oil type and volume, filtration and change interval, cooling arrangement, the pressure relief setting and where it discharges, and the floor loading. For electromechanical frames, ask the speed range at the slow end, because low-speed stability is what plastics and elastomer methods need.
Most of these machines are quoted with software, and one record is named after a software product. Four questions decide whether that software is an asset or a liability in five years. What does it calculate and report, and can raw data be exported in a format a spreadsheet reads? What are the licence terms, how many seats, and what does an extra seat cost? Which operating systems does it support, and will it install on the machines your laboratory actually has - ask for a demonstration under those conditions. And can the machine run a test and give a peak load without the computer? A testing frame should last twenty years; software generations are shorter than that.
Ask also how test methods are stored and whether the method library can be backed up and moved to a replacement computer, since a laboratory that loses its methods loses its history of comparability.
UTM-0016 is a digital impact testing machine - a pendulum that swings into a notched specimen and reports the energy absorbed. Three things to settle.
Specimen preparation. In a notched impact test the notch is the result: tip radius and depth set the stress concentration, so a worn notch cutter produces a blunter notch and a falsely tough material. The motorised notch cutter is listed under plastic testing equipment and should be bought with the machine. Ask also about certified reference specimens for verifying the machine, because they are how an impact tester is checked.
Temperature. Many metal specifications call for impact energy at a low temperature, because the transition from ductile to brittle behaviour is the property of interest. That needs a cooling bath, a means of measuring specimen temperature, and tongs that transfer the specimen into the machine within the few seconds the standard allows. Ask whether a low-temperature arrangement is offered; without it, a low-temperature specification cannot be met.
Guarding. A pendulum impact tester is the most dangerous machine in most materials laboratories: it stores a large amount of energy, releases it in a moment and throws specimen halves. Ask for fixed guards or an interlocked enclosure, a safe release and latching mechanism, a specimen catcher, bolt-down fixing, and a written rule that nobody stands in the plane of the swing while the pendulum is raised.
Rockwell and Brinell hardness. The scales are not interchangeable and a specification names one. Rockwell reads directly from the depth of indentation; Brinell requires the diameter of the indentation to be measured optically, so the result depends on how well that is read - which is why a computerised Brinell with automatic indentation measurement is worth its premium in a busy laboratory. For both, ask what indenters and loads are included against the scales you need, what certified test blocks are supplied for verification, and what anvils and supports come with the machine. One practical rule worth teaching: a specimen that is not firmly supported moves during the test and reads soft, so the anvil has to suit the shape. More on choosing a scale is on our hardness testing machines page.
The Erichsen cupping tester. A sheet-metal formability test: a punch is pressed into a clamped sheet until it cracks, and the depth at cracking is the index. Ask the punch and die specification, the sheet thickness range and how cracking is judged, and whether the instrument is manual or motorised. It is a different test from a cup-drawing test run on a universal frame, and a specification names one.
The ultrasonic flaw detector. This is non-destructive testing rather than mechanical testing - it finds internal defects in welds, castings and forgings by ultrasound. The instrument is the smaller half of the purchase: it needs probes at the frequencies and angles your work requires, couplant, calibration blocks, and above all an operator with a recognised non-destructive testing qualification. An ultrasonic result is a judgement made by a person, and in most codes the person must be certificated to a named level for the result to be accepted. Ask us what probes and reference blocks are supplied; ask your own quality manager about certification before buying the instrument.
A testing machine stores energy in the specimen and releases it at failure. On metals, bar, concrete cubes and composites that release is violent. Ask for: polycarbonate screens or an interlocked enclosure; an emergency stop within reach of where the operator stands; crosshead limit stops set so the machine cannot drive fixtures together; a specimen catcher or debris containment for compression work, because a concrete specimen fails explosively and a guard is not optional; and the bolt-down requirement, mass and floor loading. For hydraulic systems, add the relief setting, hose condition and routing, and a drip tray.
Frame type and capacity; load cell capacities with accuracy as a percentage of reading and the lower limit of the valid range; verification class and certificate; crosshead speed range and control modes, including whether load, strain and position control are available; vertical test space and throat depth; the complete fixture list written against your standards, with prices; extensometer type, gauge length and accuracy; software functions, licence terms, export format, supported operating systems and manual fallback; guarding and emergency stop arrangements; mass, footprint, floor loading and bolt-down requirement; for hydraulic machines the power pack, oil, cooling and noise; nominal voltage, frequency, phases and plug pattern; consumables and spares with prices, which here means jaws and grip faces, platens, bend rollers, indenters, test blocks, hoses and seals; and the warranty, commissioning, operator training and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you rely on it in a tender or an accreditation file.
Related ranges: tensile testing machines if every test you run is in tension, hardness testing machines for the other hardness methods, plastic testing equipment, rubber testing equipment and paper and packaging testing equipment for material-specific instruments, and wood testing machines for timber work, which is done on these frames with wood fixtures. The full set is listed under raw products testing. For a quotation, tell us the destination country, the materials and standards you test, your highest and lowest expected loads, and whether any method needs strain measurement or low-temperature impact - those answers decide the machine.
Choose by principle before capacity. Electromechanical frames, driven by screws, give finer control and better resolution at low loads, and their slow-end speed stability is what plastics and elastomer methods need. Servo-hydraulic frames, driven by a power pack, give large forces in a compact frame and handle cyclic work. A machine chosen the wrong way round performs poorly at both ends. For hydraulic frames, also ask the power pack rating, noise, oil type and volume, filtration, cooling, relief setting and floor loading; for electromechanical frames, ask the speed range at the slow end.
Rarely well. Accuracy on a testing machine is normally quoted as a percentage of reading, valid down to a stated fraction of capacity; below that the machine is simply not specified. A frame sized for reinforcing bar cannot certify a result on a plastic film or a yarn, however impressive its headline capacity. If your materials span orders of magnitude, the honest answers are interchangeable load cells on one frame, or two machines - a large frame for metals and concrete and a small one for polymers, paper and textiles. Ask us to quote both ways and compare.
Because crosshead movement is not specimen strain. It includes the deflection of the whole load train and any slip in the grips, so a modulus calculated from it is wrong. Strain should be measured on the specimen with an extensometer, and this listing includes a set of extensometers; ask the type, gauge length and accuracy, and whether the machine offers load, strain and position control. Ask also which verification class the force-measuring system is verified to and over what range of force, and contact us for the latest copies of the relevant certificates - a calibration sticker is not the same thing.
Four questions decide whether it is an asset or a liability in five years. What it calculates and reports, and whether raw data exports in a format a spreadsheet reads. The licence terms and number of seats. Which operating systems it supports - ask for a demonstration on the computers your laboratory actually has. And whether the machine can run a test and give a peak load without the computer, since a frame should last twenty years and software generations are shorter. Ask also whether the method library can be backed up and moved to a replacement computer.
Three things. Specimen preparation: in a notched impact test the notch is the result, and a worn cutter gives a blunter notch and a falsely tough material, so buy the motorised notch cutter (listed under plastic testing equipment) with the machine, and ask about reference specimens for verification. Temperature: many metal specifications call for low-temperature impact energy, which needs a cooling bath, specimen temperature measurement and tongs fast enough for the transfer time the standard allows. Guarding: fixed guards or an interlocked enclosure, safe release and latching, a specimen catcher, bolt-down, and nobody in the plane of the swing.
They are filed here rather than where a buyer would look. The Rockwell hardness testing machine (UTM-0007) and the computerised Brinell (UTM-0012) belong with hardness testing machines; their scales are not interchangeable, a specification names one, and a computerised Brinell with automatic indentation measurement removes the optical reading error. Ask the indenters, loads, test blocks and anvils supplied. The ultrasonic flaw detector is non-destructive testing: it needs probes, couplant, calibration blocks and an operator with a recognised qualification, so ask your quality manager about operator certification before buying it.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Specifications - frame type and capacity, load cell accuracy and valid range, speed range and control modes, test space, fixture list, extensometer, software terms, guarding and floor loading - are confirmed in writing on the quotation. For verification, calibration or other certificates, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing notes: four records are named only as a version (for example a hydraulic computerised version) without capacity or frame type; one record is named after a software product; the Rockwell (UTM-0007) and Brinell (UTM-0012) hardness testers are filed here rather than under hardness testing machines; the ultrasonic flaw detector belongs with non-destructive testing; and the impact tester and Erichsen cupping tester are not universal frames.
Highlights: Automatic shaft upamp; down Dwell time setting Computerized framework i.e. Brinell Image Analysis frameworks (B.I.A.S.) PCamp; Window (XP) Operating framework secured by client Range of estimation is from 1 mm to 6 mm width with the determination of 0.01 mm Software Features: Well overseen information base Saves readings as for clump and testament Report age as authentication and chart Designed as per International Standards: Technical Specifications: Load (kgf) 250, 500, 750, 1000, 1500, 2000, 2500 and 3000 kgf Load Control Auto (By Hydraulic ) Start Operation Automatic begin (By push catch/Hydraulic Power Pack) Dwell Time 0 to 99 seconds Accuracy Conforms to ASTM-E 10/IS 1500 Max. Example Height 9.5 in. (240 mm) Max. Example Depth 50 in. (130 mm) Initial load Nil Size of BAE 370 x 670 mm Driver engine 0.33-415 V/P HP Main supply/Cy/PH 415/50/3 Standard Accessories: Anvil, Flat (7.9 in./200 mm) Anvil, Flat (2.4 in/60 mm) Anvil, V ( 2.4 in/60 mm) Hardness Standard Ball Indenter (0.4 in./10 mmamp; 5mm) Spare Fuse Power Cord Dust Cover Instruction Manual Hardness Conversion Table. Steel Metal Mechanics Lab hardware manufacturers,exporters and Steel Metal Mechanics Lab providers
Details: 400/440V, 50Hz Three Phase A.C Supply 1.5 H.P with water powered framework Designed to perform assortment of tests like strain, pressure, and so on metallic materials. Consistent roll autographic load recorder Provision for PC with easy to understand programming Auto location and turning off arrangement in the event of over load, over movement and example break. Simple and electronic control board Capacity: 200KN Max. Range: 10-200KN ±0.1 KN Min. Range: 0-20KN ±0.01KN Maximum elastic freedom at full : (50-700 mm) decedent cylinder position Distance between sections: 500 mm. Cylinder stroke: approx 200 mm. Max Clearance for pressure rest : 0-700(mm) Max. Stressing speed at No. Load : 150(mm/min) Standard Accessories: Pair of pressure plates dia 120 mm For Tension Test Jaws: Round example dia 10-20 mm Round example dia 20-30 mm Flat example thickness 0-10 mm Flat example thickness 10-20 mm Max. width for level example 50 mm For Transverse Test: Adjustable Roller Support of width approx. 150 mm Adjustable Roller Support of dia. approx. 30 mm With max customizable freedom approx. 500 mm RS232 Serial Port/Data Cable Optional Accessories: Extensometer Load rate Control Load rate stabilizers Flat Belt test Bolt nut and Washer test Single and twofold shear test Tensile test for bore and strung Bend Re-twist test
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India.
General Testing Machine Application System Peak stack alongside on line stack. Greatest lengthening with online prolongation. Extreme Tensile Strength Graphical Display of load versus time. Graphical Display of lengthening versus time. Graphical Display of load versus lengthening. Graphical Display of pressure versus strain. Finish Statistical Analysis. Date Report Management. Wellbeing Features: Machine stops after example disappointment. Wellbeing against Over movement of cylinder. Protect against high temeprature. Surge Protector. Auto Machine Diagnosis. Wellbeing against over-burden. PC Configuration: Processor: Pentium IV/AMD 64 BIT. Preparing Speed: 2.0 GHZ or higher. H.D. Drive: 80 GB. Slam: 256 MB. Cd ROM: 52 X. F.D.D.: 1.44 MB. Shading Monitor: 17" SVGA. Console: 104 Key. Printer: Inkjet. Printer: Laser (Optional at additional cost). Mouse Optical. UPS of no less than 600 VA limit Software: Preloaded with window 2000 based programming. The Software gave on CD ROM. Programmed sparing and giving database to completing factual computation of different test outcomes. Programming application should be fit for giving capacity like Auto Return to Zero.
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India.
Centralized server: The machine embrace twofold space entryway write structure. High precision, wide range and stable AC servo engine drive the ball screw match turning through syn-deceleration framework. The ball screw match drives the center crosshead and makes the pressure/pressure/twisting connection climbs and down to understand the heap and offload to the example. This structure has enough solidness to apply high proficiency and stable moving. Key parts are handled without anyone else preparing focus to guarantee the precision of the heap outline. Ball screw is E5 class Features: Complete PC controlled: The entire estimating and controlling framework embraces particular PC control card utilized for testing machines, understanding the information zero and in addition to alteration, which has high dependability. Supporting multi-transducers Realizing the database administration of the test information which are put away as per the standard configuration; encouraging other programming to investigate and exchange. Consummate programming via auto program control, each control mode can easily move to another. Satisfying the test necessity of a wide range of materials with each test standard home and abroad. Control programming has the auto-changing capacity of test hardness, which guarantees that the framework works with each sort of example hardness. Idealize realistic capacity understanding the discretionarily amplifying, diminishing, leveling with, including, demonstrative show and print of a wide range of test bends, the test point seeking and in addition the concurrent show and print of a few sorts of test bends. Information preparing assumes self-arranging and info discarding realistic human PC cooperation, which encourages the check and complexity of the test outcome. The client can self - characterize the yield of the test report, which influences the answer to arrange have high adaptability. Modularization configuration encourages the product redesigning, work spreading and in addition the second advancement. All the critical parts were prepared by our own handling focus to ensure the high precision of machine. Programming highlights: MS windows based interface, simple and quick to achieve distinctive capacities, appropriate for a large portion of administrators utilizing propensities. Incorporated all basic activity capacities, similar to example data input, example picking, Curve lengthening, information show, date process, information investigation, test task and so forth., simple and advantageous to work.
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India.
Specialized Specifications Maximum limit : 300J for Charpy Test, 170J for Izod Test Minimum Scale Graduation : 0.5 J Pendulum drop plot for Charpy : 140° Pendulum drop plot for Izop : 90° Pendulum Weight : 22 Kg Striking Velocity : Charpy-5.3 m/s, Izod-3.9m/s Distance of Pendulum focus to example Center : - 815 mm Accuracy : + 0.5 J DRO for vitality consumed by Specimen Printer Facilityn dash; To print the vitality of example after test Selection switch for charpy or Izod Test Accuracy according to IS amp; BS Standards Accessories amp; Spares: Charpy/Izod Caliper Gauge Self Centering Tong Izod Charpy Sq. Format Depth Notch Gauge `U' Notch Width Gauge `V' Notch Angle Gauge `U' Notch Milling shaper `V' Notch Milling Cutter. Steel Metal Mechanics Lab hardware manufacturers, exporters and Steel Metal Mechanics Lab providers
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments manufacturers, engineering lab equipments manufacturers, physics lab engineering equipment exporter, engineering educational equipment india, engineering lab equipments suppliers, engineering educational equipments supplier in Ambala, India.
RAYEXPORT is Manufacturer, Exporter amp; Supplier of & Erichsen Cupping Tester. mechanical lab types of gear makers. Steel Metal Mechanics Lab hardware manufacturers ,exporters and Steel Metal Mechanics Lab providers
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments manufacturers, engineering lab equipments manufacturers, physics lab engineering equipment exporter, engineering educational equipment india, engineering lab equipments suppliers, engineering educational equipments supplier in Ambala, India.
All inclusive Testing Machine Standard Accessories For Tension Test : Clamping Jaws for Testing Round Specimens under Tension Clamping Jaws for Testing Flat Specimens under Tension For Compression Test : A couple of pressure platens, appropriately solidified, ground and cleaned with base platen furnished with rules for putting the test example co-hub with the water powered smash. For Bending/Transverse Test: Table with Adjustable Rollers finish with Mandrel for leading Bending/Transverse Test. Discretionary Accessories : The Universal Testing Machine is made more adaptable and utility situated for completing various different tests also with Accessories/Attachments that are Optional. These Optional Accessories/Attachments are evaluated ostensibly and are very essential particularly for Technical Institutions. Load Stabilizer. Brinell hardness Test Attachment. Twofold Shear Test Attachment : Small amp; Large. 180° Bend Test Attachment. Exposed Attachment. Hedges for Testing Threaded Specimens. Hedges for Testing Collared Specimens. Connection for Testing Wire amp; Manila Ropes. Extensometers : Mechanical/Electronic with Firedamp; Variable Gauge Length. Flexure Testing Attachment.. Steel Metal Mechanics Lab gear manufacturers ,exporters and Steel Metal Mechanics Lab providers
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments exporters, engineering lab equipments manufacturers in india, engineering educational equipment manufacturer, mechanical engineering lab equipments suppliers, engineering lab equipments supplier, engineering educational equipment supplier in Ambala, India.
Highlights: The capacity to play out all usually utilized mechanical tests. The capacity to make your own test techniques for an assortment of necessities. Spare and review test techniques for exact and repeatable testing. Secret word ensured chief/administrator modes permit test techniques to be actuated at that point bolted under watchword so they can't be changed accidentally. Figuring of key test parameters, for example, Ultimate Load, Offset Yield, Modulus of Elasticity and then some. WinTest highlights a broad arrangement of information examinations. Contact the industrial facility for a progressive posting. Count of high, low, mean and standard deviation for a gathering of tests.- time information, for example, magnifying lens pictures. Printed version printouts of single test reports, assemble test reports and X-Y plots. Capacity of test information and results to hard plate in ASCII delimited arrangement for simple import into well known spreadsheet and database programs. Up to ten client quantifiable test data and twenty report header fields to meet an assortment of testing and detailing necessities. Client selectable English, Metric and SI units. Substantial simple to-peruse numeric presentations that show live, pinnacle and rate readings. Continuous plotting of test information. Shut circle servo control with PID pay. Incorporates monotonic, cyclic and sectioned control profiles with programming selectable control channels which can be changed on the fly. The capacity to change control additions and endpoint esteems amid a test. Perfect for framework tuning amid dynamic weariness tests. Five information channels for stack, crosshead position, hub strain, transverse strain and one assistant information. Power and extensometer strain exactness surpasses ATSM E-4 and E-83 measures, individually. Three extra helper input channels are alternatively accessible. Programmed transducer recognizable proof accessible on all channels. Boundless alignment tables per simple channel for numerous heap cell and extensometer prerequisites. Up to 10 adjustment focuses per transducer with piecewise direct fit between focuses for most extreme accuracy.All alignments are watchword ensured and are spared to plate. Consistent access to a large number of today's prominent spreadsheet programs. Access XY information ongoing for arrangement with other realtime information, for example, magnifying lens pictures.. Steel Metal Mechanics Lab gear manufacturers,exporters and Steel Metal Mechanics Lab providers
The machine is using pressurized water worked, vertical, floor mounted, intended for testing metals and different materials under Tension, Compression, Bending/Transverse Loads. The Machine contains stacking unit and control Panel. Stacking Unit: This comprise of a water powered chamber engine with chain and sprocket drive and a table combined with the smash of the pressure driven barrel, mounted on to a vigorous base. The chamber and the smash are independently lapped to kill erosion . the upper cross head is unbendingly settled to the table by two straight segments the lower cross head is associated with two screwed sections which are driven by an engine , hub stacking of the smash is guaranteed by diminishing the chamber and slam of the any conceivable side stacking by the arrangement of ball seating Tension test is led by grasping the test example between the upper lower cross-head s pressure navigate , bowing shear and hardness tests are directed between the lower cross-head and the table. The lower cross head can be raised or bring down quickly by the working the screwed sections in this manner, encouraging simplicity of settling of the test examples Technical Features: Stress Controlled 0.1kN/min. to Full Load kN/min. Strain Controlled 0.01 mm/min. to 100 mm/min. Torque Compensated Power Pack for 100% Oil Delivery at all Load Values Air Cooled bury cooler for keeping up oil temperature underneath 45° at running conditions 100% control by means of Rj45/USB Interface On-Board Characteristics direct punch Fully Computer Controlled Bumpless P.I.D Control utilizing programming controllable PID settings Dual Channel moving 64 KHz information examining rate Capacity : Upto 3000 kN) With On-Line use of programming for producing test reports and graphical plots - Loading/Straining Rate control - with unending permit Least Count : 0.001 kN for Load Accuracy : 0.5% Displacement Resolution : 0.001 mm Loading and Straining Rate controlled through PC. Least Loading Rate : 0.5% (of Machine Capacity) to Full Scale stack every moment Maximum Load Rate : Full Scale Load every moment Minimum Strain Rate 0.01 mm for each Minute to 100 mm/Minute On-Line Graph on PC or on standard PC, framework Batch Test Facility (upto 10 bends on single diagram) Hydraulic Pump withstand a most extreme weight up to 250 kg/cm² High Pressure Hydraulic Flexible Pipes/Anti Corrosive steel&. Steel Metal Mechanics Lab hardware manufacturers ,exporters and Steel Metal Mechanics Lab providers.
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments exporters, engineering lab equipments manufacturers in india, engineering educational equipment manufacturer, mechanical engineering lab equipments suppliers, engineering lab equipments supplier, engineering educational equipment supplier in Ambala, India.