Quick answer. Decide first whether you are equipping teaching benches or a production bay, because that decides single-socket against gang programmer. Students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit; the eight gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025) earn their place where a department also turns out batches in a production or project workshop. Then choose by device list and interface, not by name: the superlatives in these titles - ultra-high, ultra-fast, advanced, handy - are not specifications.
Forty-one items are listed here, ETT-0001 to ETT-0041. Despite the category name there are no hand tools in it. What it actually contains is four quite different things: device programmers, which are the bulk of it, integrated circuit testers, programmable-logic trainer kits and embedded trainers. Several items share identical names, and the fuller listings for three of the four groups are elsewhere on this site, so the table below says where to look as well as what is here.
| Group | Codes | Fuller listing on this site |
|---|---|---|
| Single-socket programmers, microcontroller and memory | ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021 | EPROM Programmer and Programmer Tester |
| Gang programmers, several devices at a time | ETT-0013 to ETT-0016, ETT-0022 to ETT-0025 | Only here |
| Ultraviolet eraser | ETT-0018 | EPROM Programmer and Programmer Tester, where the ultraviolet safety requirements are set out in full |
| Integrated circuit testers | ETT-0026 to ETT-0032 | IC Tester and Digital IC Tester |
| Programmable-logic trainer kits and a simulator | ETT-0034 to ETT-0038 | VLSI Design Training Systems |
| Embedded trainers | ETT-0039, ETT-0040, ETT-0041, all three under the same name | Embedded System Trainers |
| Named only as a word | ETT-0033, listed as "Experiments" | Ask what it is |
Fourteen single-socket programmers are listed under names built largely on superlatives, ultra-high, ultra-fast, advanced, handy. None of those is a specification. Send the supplier the list of parts your laboratory actually programmes and ask for written confirmation, part by part, plus:
Eight codes here are gang programmers, which hold several devices and programme them together. They exist for small-batch production, where the cost per programmed part matters, and they are the one group in this listing with no fuller counterpart elsewhere on the site. Before buying one for a teaching laboratory, be clear that a class does not need one: students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit. A gang programmer earns its place where a department also runs a production or project workshop turning out batches.
If that is your case, ask: how many sockets; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether the unit runs standalone from a stored image, which is what makes it usable by a production operator rather than a programmer; and whether sockets can be replaced individually, since they wear out with use.
Integrated circuit testers (ETT-0026 to ETT-0032). Seven codes including three handheld digital testers, an analogue tester and three universal testers. The important point is what these instruments can and cannot tell you: they test function against a stored library, not data sheet parameters, so a device that passes can still be out of specification, and a re-marked part that happens to pass will read as good. That is set out at length under IC Tester and Digital IC Tester, which also carries the same instruments under another code series; compare the two listings before ordering.
Programmable-logic kits (ETT-0034 to ETT-0038). A field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For all of these the decisive question is the design software: which tool and which version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. The same question, with the reasons, is under VLSI Design Training Systems. For the simulator, ask what it simulates, which language and version, how many seats and what the licence costs each year.
Embedded trainers (ETT-0039 to ETT-0041). All three carry the same name. Ask what distinguishes them and which is current, then compare against Embedded System Trainers, which lists thirty boards with the processor families named.
Quote the code, not the name: ETT-0013 and ETT-0014 carry the same name, ETT-0024 and ETT-0025 carry the same name, ETT-0039 to ETT-0041 all three carry the same name, and two names appear truncated, ETT-0004 ending in "Program" and ETT-0006 in "Serial". Where a code is named after a commercial device family, ask whether the kit is manufactured by Ray Export or supplied as a traded product and who supports it. Ask also for the manual, the supported device list as a document rather than a count, the quantity needed, the supply voltage, frequency and plug type for your country, spare sockets and adapters with prices, and the warranty. For ETT-0018, read the ultraviolet safety requirements before use: the lamp is invisible and gives no warning sensation, the lid interlock must work and must never be defeated, and the unit needs ventilation.
Programming and erasing: EPROM Programmer and Programmer Tester. Device testing: IC Tester and Digital IC Tester. The boards these devices go into: Microprocessor Trainers and Kits, Embedded System Trainers and VLSI Design Training Systems. The bench they are used at: Soldering and Desoldering Stations. Components: Electronic Components. Instruments: Testing and Measuring Lab Trainers. Parent range: Training Kits.
Send your device list and say whether you are equipping benches or a production bay, since that decides single-socket against gang. For example two universal-serial-bus programmers with in-system programming (from ETT-0017 or ETT-0020), with the device list, the update policy and the software licence confirmed in writing. Contact Ray Export for prices, device lists and lead times.
Despite the name, there are no hand tools. ETT-0001 to ETT-0041 cover single-socket programmers (ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021), gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025), an ultraviolet eraser (ETT-0018), integrated circuit testers (ETT-0026 to ETT-0032), programmable-logic kits and a simulator (ETT-0034 to ETT-0038) and three embedded trainers (ETT-0039 to ETT-0041). ETT-0033 is listed only as Experiments, so ask what it is. For every group except the gang programmers, a fuller listing exists elsewhere on this site, so compare before ordering.
Ignore the adjectives and send the list of parts your laboratory actually programmes, asking for written confirmation part by part. Then ask how the device library is updated and whether updates are free and for how long; the socket pin count (one code names a 144-pin socket, the others do not) and the adapters for surface-mount packages; whether in-system programming through a header is supported and the cable included; and, where speed is claimed, a figure in seconds for a full programme-and-verify cycle on a named device. Ask too whether the unit can set lock bits, which is often irreversible.
Not directly. Several codes here are serial-port programmers, including ETT-0002, ETT-0004 and ETT-0006, and current computers do not have serial ports. Those units need a converter, which may or may not work with the programming software, so ask before ordering or choose the universal-serial-bus versions - for example ETT-0017 or ETT-0020 with in-system programming. Whichever you choose, ask whether it runs standalone or needs a computer, and if a computer, which operating system, whether the software licence is included and whether the drivers work on your machines.
First, whether you need one: a class does not, because students programme one device each. If your department also runs a production or project workshop, ask how many sockets there are; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether it runs standalone from a stored image; and whether sockets can be replaced individually.
The design software. ETT-0034 to ETT-0038 comprise a field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For each kit, ask which tool and version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. For the simulator, ask what it simulates, which language and version, how many seats, and the licence terms. For kits named after a commercial device family, ask who manufactures and supports them.
Possibly, so compare before ordering. ETT-0026 to ETT-0032 are seven testers - three handheld digital testers, an analogue tester and three universal testers - and the IC Tester and Digital IC Tester listing carries the same instruments under another code series. Remember that they test function against a stored library, not data sheet parameters, so a passing device can still be out of specification and a re-marked part can read as good. ETT-0039 to ETT-0041 share one name; ask what distinguishes them and compare against Embedded System Trainers, which names the processor families.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Every specification, including the supported device list, socket, interface, software licence and throughput, is confirmed in writing on the quotation; ask for the device list as a document rather than a count. For certificates, contact us for the latest copies of the relevant certificates. No price is quoted here. Listing defects noticed: the category is named Training Tools but holds no hand tools; ETT-0013 and ETT-0014, ETT-0024 and ETT-0025, and ETT-0039 to ETT-0041 share names; ETT-0004 and ETT-0006 have truncated names; ETT-0033 is listed only as Experiments; product titles rely on superlatives rather than specifications; and the IC testers also appear in the IC Tester and Digital IC Tester listing under another code series.
Equipment for Education, Engineering and Vocational Training - FEATURES Universal IC Tester with Membrane ASCII Keypadis a Table-Top version, designed as a powerful tool for manufacturers, servicing engineers, R&D personnels to test a wide range of IC's of Digital,Analog, CPU & RAMs. Tests Digital and Analog ICs from 3 to 40 Pins. Built in self-diagnostic functions to ensure error free testing of IC. 16 character x 2 line backlit LCD display and sealed Membrane type Alpha Numeric keyboard Automatic testing of variety of ICs. 2 nos. of potential free 40 pin ZIF sockets for testing analog and digital ICs. Single step mode enables the user to test the IC step by step. Audio alarm to user whenever it is required. IC PACK : Digital ICs up to 40 pins and analog ICs up to 20 pins in DIP package. IC TYPE : Tristate, open collector & bidirectional TTL/CMOS digital ICs also analog ICs as per list. TEST BY : Truth table comparison for digital ICs. Functional test of output for various input conditions for analog ICs. ZIF : Two 40 pin DIP ZIFs for analog and digital ICs. KEY : Membrane type Alpha Numeric 50 Keys Keyboard. DISPLAY : 16 character x 2 line backlit LCD SUPPLY VOLTAGE : 180V to 270, 50Hz single phase. RANGE OF ICs THAT CAN BE TESTED : DIGITAL : TTL, CMOS ICs including SSI, MSI, LSI, Functions including Gates, Buffers, Drivers, Flip-flops Counters, Shift registers, Latches, Multiplexers, Parity generators, Analog switches, CPUs, Microcontrollers, Peripherals, Static RAMs, Non volatile rams, Serial EPROMs etc. LINEAR : Transistor Arrays, Timers, Analog switches, Optocouplers, Display drivers, Line drivers, and Latch drivers, 7 segment display, LCD display, from 16 character by 1 row Upto 40 characters by 2 rows, Real time clocks, Analog to Digital converters upto 16 bit resolution and upto 40 pin Devices. Digital to Analog converters. Op-Amp’s (8 Pin 14 Pin, 16 pin). Comparators (8 pin, 14 pin, 16 pin) Op-Amp and Comparators (combined) Voltage followers (8 pin, 14 pin) Voltage regulators (Both +ve and –ve), DPM ICs, DOT / BAR display drivers, PLLs, VCOs. Waveform Generator, Sample & Holds, PWM Generators..
Equipment for Education, Engineering and Vocational Training - ests most of the 6 to 40 pin ICs in DIP package. The list includes 74/54, 40/45, 93/96 series ICs, EPROMs, RAMs, peripheral ICs, microprocessor (8088/8085/Z80/6502), operational amplifiers, voltage comparators, transistor arrays, optocouplers, analog switches, voltage followers, timers, A to D converters, D to A converters and miscellaneous analog ICs. Automatic testing of variety of ICs. Potential free 40 pin universal ZIF socket. Six Seven Segment Display to show IC number, PASS & FAIL Status, Operations display. It has 16/24 keys for its operation. Battery & Mains operation Portable size Audio alarm to user whenever it is required..
Equipment for Education, Engineering and Vocational Training - Logic Gates - Design of Gates - Design of AND gate - Design of OR gate - Design of XOR gate - Design of XOR gate using other basic gates - Design of 2:1 Mux using other basic gates - Design of 2 to 4 Decoder - Design of Half-Adder, Full Adder, Half Subtractor, Full Subtractor - Design of 3:8 Decoder - Design of 8:3 Priority Encoder - Design of 4 Bit Binary to Grey code Converter - Design of 4 Bit Binary to BCD Converter using sequential statement - Design an 8 Bit parity generator (with for loop and Generic statements) - Design of 2,s Complementor for 8-bit Binary number using Generate statements Sequential Design Exercises - Design of all type of Flip-Flops using (if-then-else) Sequential Constructs - Design of 8-Bit Shift Register with shift Right, Rshift Left, Load and Synchronous reset. - Design of Synchronous 8-bit Johnson Counter. - Design of Synchronous 8-Bit universal shift register (parallel-in, parallel-out) with 3- state output (IC 74299) - Design of 4 Bit Binary to BCD Converter using sequential statement. - Design - a) Mod 3 Counter - b) Mod 5 Counter - c) Mod 7 Counter - d) Mod 8 Counter - e) Mod 16 counter - f) 4 Bit Johnson counter - Design a decimal up/down counter that counts up from 00 to 99 or down from 99 to 00. - Design 3-line to 8-line decoder with address latch - Design of ALU 55 - Lab Project/Case Studies: 2 Nos..
Equipment for Education, Engineering and Vocational Training - It uses Xilinx Spartan XC2S50/XC2S100/XC2S200 FPGA with up to 50/100/200K system gates, and up to 200MHz clock speed. - It communicates with computer through standard Webpack - User can develop the circuit/ schematic using Xilinx standard Foundation Series Software and any development tool for VLSI design available in the world. - It has various on-board interfaces: - 16x2 LCD module - Six Seven Segment Displays - Stepper Motor Controller Interface - 8x8 LED Matrix Display - EWSN Status LED's 12 Nos. - ADC/DAC Interface - RS-232 interface - Parallel JTAG interface - Four Data Switches - Switch Array - AT24C16 Serial EEPROM - 4x4 Keyboard - Power Indicator LED - It has on board 89C51RD2 for development and processing of 51 family softwares. - On board microcontroller with 64K flash, 1K RAM ISP with required software. - It has I/O counter interface to enable it to connect various demo modules. This helps in man to machine interface. - Has a general purpose areas on board to enable it to incorporate additional circuit. - VPL-SPARTAN Board - Set of cables flat and serial - Application CD ROM - User's manual: detailed information on components and usage - Data sheet of major components - List of experiments for FPGA as listed - On board facility for variable clock generation.
Equipment for Education, Engineering and Vocational Training - It uses industry standard CPLD 95C108 with optional facility for 9536 and 9572 - It communicates with computer through standard Webpack - It has a serial & parallel link which enable user to communicate with PC. - User can develop the circuit/schematic using Xilinx standard Foundation Series Software and any development tool for VLSI design available in the world. - It has various on-board interfaces: - 16x2 LCD module - Six Seven Segment Displays - Stepper Motor Controller Interface - 8x8 LED Matrix Display - EWSN Status LED's 12 Nos. - ADC/DAC Interface - RS-232 interface - Parallel JTAG interface - Four Data Switches - Switch Array - AT24C16 Serial EEPROM - 4x4 Keyboard - Power Indicator LED - On board microcontroller with 64K flash, 1K RAM ISP with required software. - It has I/O counter interface to enable it to connect various demo modules. This helps in man to machine interface. - Has a general purpose areas on board to enable it to incorporate additional circuit. PACKAGE CONTENTS - VPL-CPLD Card - Set of cables flat and serial - Application CD ROM - User's manual: detailed information on components and usage - Data sheet of major components - List of experiments for CPLD as listed - On board facility for variable clock generation.
Equipment for Education, Engineering and Vocational Training - It uses industry standard Virtex 600 - It communicates with computer through standard Webpack - It has a serial & parallel link which enable user to communicate with PC. - User can develop the circuit/schematic using Xilinx standard Foundation Series Software and any development tool for VLSI design available in the world. - It has various on-board interfaces: - 16x2 LCD module - Six Seven Segment Displays - Stepper Motor Controller Interface - 8x8 LED Matrix Display - EWSN Status LED's 12 Nos. - ADC/DAC Interface - RS-232 interface - Parallel JTAG interface - Four Data Switches - Switch Array - AT24C16 Serial EEPROM - 4x4 Keyboard - Power Indicator LED - On board microcontroller with 64K flash, 1K RAM ISP with required software. - It has I/O counter interface to enable it to connect various demo modules. This helps in man to machine interface. - Has a general purpose areas on board to enable it to incorporate additional circuit. PACKAGE CONTENTS - VPL-CPLD Card - Set of cables flat and serial - Application CD ROM - User's manual: detailed information on components and usage - Data sheet of major components - List of experiments for CPLD as listed - On board facility for variable clock generation.
Equipment for Education, Engineering and Vocational Training - It uses industry standard Altera CPLD 7128/1K50 - It communicates with computer through standard Webpack - It has a serial & parallel link which enable user to communicate with PC. - User can develop the circuit/schematic using Xilinx standard Foundation Series Software and any development tool for VLSI design available in the world. - It has various on-board interfaces: - 16x2 LCD module - Six Seven Segment Displays - Stepper Motor Controller Interface - 8x8 LED Matrix Display - EWSN Status LED's 12 Nos. - ADC/DAC Interface - RS-232 interface - Parallel JTAG interface - Four Data Switches - Switch Array - AT24C16 Serial EEPROM - 4x4 Keyboard - Power Indicator LED - On board microcontroller with 64K flash, 1K RAM ISP with required software. - It has I/O counter interface to enable it to connect various demo modules. This helps in man to machine interface. - Has a general purpose areas on board to enable it to incorporate additional circuit. PACKAGE CONTENTS - VPL-CPLD Card - Set of cables flat and serial - Application CD ROM - User's manual: detailed information on components and usage - Data sheet of major components - List of experiments for CPLD as listed - On board facility for variable clock generation.
Equipment for Education, Engineering and Vocational Training - Learn VHDL the Direct way with our low-cost, interactive VHDL simulator. DirectVHDL is built around a VHDL interpreter that allows you to edit and simulate your VHDL design without complicated setup or compilation procedures. DirectVHDL simply loads and simulates in one step. DirectVHDL includes the following: - VHDL Workspace - An easy-to-use manager that serves as a starting point to launch the VHDL editor and simulator. - VHDL Editor - An advanced editor providing syntax coloring and syntax-error detection. Perfect for beginners, this editor highlights syntax errors as you type! - VHDL Simulator - Allows you to simulate and debug your design with a graphical waveform viewer. - VHDL Tutorial - Provides an easy introduction to the VHDL language. Requirements - Windows - Windows 95,98,Me,NT 4.0, or 2000, 15 MB hard disk space, 64 MB RAM. - Mac OS X IMPLEMENTATION & EXPERIMENTAL BOARDS(More than 20 hardware experiments) - Universal FPGA/CPLD Kit - Training Kits for Virtex, Spartan 2S, 2SE, CPLD, - FPGA,Altera.
Equipment for Education, Engineering and Vocational Training - CPU: Philips 89V51RD2 Microcontroller - Six Seven Segment Displays - Stepper Motor Controller Interface - LCD Display Interface - 8x8 LED Interface Block- EWSN Status LED's 12 Nos. - 8 Chanel ADC Interface- Four Data Switches - Relay- Opto - Real Time Clock- Switch Array - At24C16 Serial EEPROM - RS-232 Interface using Rx/Tx of MCU for uploading/downloading Internal Peripheral Features - On-chip Flash Program Memory with ISP and IAP capability - Parallel programming with 87C51 compatible hardware - Supports 6-clock/12-clock mode via parallel programmer - 6/12-clock mode Flash bit erasable and programmable via ISP - 6-clock/12-clock mode programmable “on-the-fly” by SFR bit - Peripherals (PCA, timers, UART) may use either 6/12-clock - Speed up to 20 MHz with 6-clock cycles per machine cycle - Pin to pin study of microcontroller unit - Indicators for data, status and control pins - Test points available for testing - Extention conectors for connecting external circuits - Fully static operation - RAM expandable externally to 64 kbytes - Four interrupt priority levels - Seven interrupt sources - Four 8-bit I/O ports - Full-duplex enhanced UART‘ - Framing erro detection - Automatic address recognition - Power control modes - Clock can be stopped and resumed - Idle mode - Power down mode - Programmable clock-out pin - Second DPTR register - Asynchronous port reset - Low EMI (inhibit ALE) - Programmable Counter Array (PCA) - PWM - Capture/compare - Assembler / 'C' compiler available.
Equipment for Education, Engineering and Vocational Training - Embedded Trainer has been designed by using Motorola 68HC11 PLCC Microcontroller. This controller provides in-system as well as in circuit programming so that one may be able to write program and download directly in the controller through serial port without removing it from the system. - CPU: Motorola 68HC11 Microcontroller - Stepper Motor Controller Interface - 16x2 LCD module- - ix Seven Segment Displays - 8x8 LED Matrix Display- EWSN Status LED's 12 Nos. - ADC/DAC Interface- Four Data Switches - Switch Array- At24C16 Serial EEPROM Peripheral Features: - M68HC11 CPU - Power-saving stop and wait modes - 0, 256, 512, or 768 bytes of on-chip RAM, data retained during standby - 0, 12, or 20 Kbytes of on-chip ROM or EPROM - 0, 512, or 2048 bytes of on-chip EEPROM with block protect for security - 2048 bytes of EEPROM with selectable base address in the MC68HC811E2 - Asynchronous non-return-to-zero (NRZ) serial communications interface (SCI) - Additional baud rates available on MC68HC(7)11E20 - Synchronous serial peripheral interface (SPI) - 8-channel, 8-bit analog-to-digital (A/D) converter - 16-bit timer system: - Three input capture (IC) channels - Four output compare (OC) channels - One additional channel, selectable as fourth IC or fifth OC - 8-bit pulse accumulator - Real-time interrupt circuit - Computer operating properly (COP) watchdog system - 38 general-purpose input/output (I/O) pins: - 16 bidirectional I/O pins - 11 input-only pins - 11 output-only pins.