Quick answer. Decide first whether you are equipping teaching benches or a production bay, because that decides single-socket against gang programmer. Students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit; the eight gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025) earn their place where a department also turns out batches in a production or project workshop. Then choose by device list and interface, not by name: the superlatives in these titles - ultra-high, ultra-fast, advanced, handy - are not specifications.
Forty-one items are listed here, ETT-0001 to ETT-0041. Despite the category name there are no hand tools in it. What it actually contains is four quite different things: device programmers, which are the bulk of it, integrated circuit testers, programmable-logic trainer kits and embedded trainers. Several items share identical names, and the fuller listings for three of the four groups are elsewhere on this site, so the table below says where to look as well as what is here.
| Group | Codes | Fuller listing on this site |
|---|---|---|
| Single-socket programmers, microcontroller and memory | ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021 | EPROM Programmer and Programmer Tester |
| Gang programmers, several devices at a time | ETT-0013 to ETT-0016, ETT-0022 to ETT-0025 | Only here |
| Ultraviolet eraser | ETT-0018 | EPROM Programmer and Programmer Tester, where the ultraviolet safety requirements are set out in full |
| Integrated circuit testers | ETT-0026 to ETT-0032 | IC Tester and Digital IC Tester |
| Programmable-logic trainer kits and a simulator | ETT-0034 to ETT-0038 | VLSI Design Training Systems |
| Embedded trainers | ETT-0039, ETT-0040, ETT-0041, all three under the same name | Embedded System Trainers |
| Named only as a word | ETT-0033, listed as "Experiments" | Ask what it is |
Fourteen single-socket programmers are listed under names built largely on superlatives, ultra-high, ultra-fast, advanced, handy. None of those is a specification. Send the supplier the list of parts your laboratory actually programmes and ask for written confirmation, part by part, plus:
Eight codes here are gang programmers, which hold several devices and programme them together. They exist for small-batch production, where the cost per programmed part matters, and they are the one group in this listing with no fuller counterpart elsewhere on the site. Before buying one for a teaching laboratory, be clear that a class does not need one: students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit. A gang programmer earns its place where a department also runs a production or project workshop turning out batches.
If that is your case, ask: how many sockets; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether the unit runs standalone from a stored image, which is what makes it usable by a production operator rather than a programmer; and whether sockets can be replaced individually, since they wear out with use.
Integrated circuit testers (ETT-0026 to ETT-0032). Seven codes including three handheld digital testers, an analogue tester and three universal testers. The important point is what these instruments can and cannot tell you: they test function against a stored library, not data sheet parameters, so a device that passes can still be out of specification, and a re-marked part that happens to pass will read as good. That is set out at length under IC Tester and Digital IC Tester, which also carries the same instruments under another code series; compare the two listings before ordering.
Programmable-logic kits (ETT-0034 to ETT-0038). A field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For all of these the decisive question is the design software: which tool and which version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. The same question, with the reasons, is under VLSI Design Training Systems. For the simulator, ask what it simulates, which language and version, how many seats and what the licence costs each year.
Embedded trainers (ETT-0039 to ETT-0041). All three carry the same name. Ask what distinguishes them and which is current, then compare against Embedded System Trainers, which lists thirty boards with the processor families named.
Quote the code, not the name: ETT-0013 and ETT-0014 carry the same name, ETT-0024 and ETT-0025 carry the same name, ETT-0039 to ETT-0041 all three carry the same name, and two names appear truncated, ETT-0004 ending in "Program" and ETT-0006 in "Serial". Where a code is named after a commercial device family, ask whether the kit is manufactured by Ray Export or supplied as a traded product and who supports it. Ask also for the manual, the supported device list as a document rather than a count, the quantity needed, the supply voltage, frequency and plug type for your country, spare sockets and adapters with prices, and the warranty. For ETT-0018, read the ultraviolet safety requirements before use: the lamp is invisible and gives no warning sensation, the lid interlock must work and must never be defeated, and the unit needs ventilation.
Programming and erasing: EPROM Programmer and Programmer Tester. Device testing: IC Tester and Digital IC Tester. The boards these devices go into: Microprocessor Trainers and Kits, Embedded System Trainers and VLSI Design Training Systems. The bench they are used at: Soldering and Desoldering Stations. Components: Electronic Components. Instruments: Testing and Measuring Lab Trainers. Parent range: Training Kits.
Send your device list and say whether you are equipping benches or a production bay, since that decides single-socket against gang. For example two universal-serial-bus programmers with in-system programming (from ETT-0017 or ETT-0020), with the device list, the update policy and the software licence confirmed in writing. Contact Ray Export for prices, device lists and lead times.
Despite the name, there are no hand tools. ETT-0001 to ETT-0041 cover single-socket programmers (ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021), gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025), an ultraviolet eraser (ETT-0018), integrated circuit testers (ETT-0026 to ETT-0032), programmable-logic kits and a simulator (ETT-0034 to ETT-0038) and three embedded trainers (ETT-0039 to ETT-0041). ETT-0033 is listed only as Experiments, so ask what it is. For every group except the gang programmers, a fuller listing exists elsewhere on this site, so compare before ordering.
Ignore the adjectives and send the list of parts your laboratory actually programmes, asking for written confirmation part by part. Then ask how the device library is updated and whether updates are free and for how long; the socket pin count (one code names a 144-pin socket, the others do not) and the adapters for surface-mount packages; whether in-system programming through a header is supported and the cable included; and, where speed is claimed, a figure in seconds for a full programme-and-verify cycle on a named device. Ask too whether the unit can set lock bits, which is often irreversible.
Not directly. Several codes here are serial-port programmers, including ETT-0002, ETT-0004 and ETT-0006, and current computers do not have serial ports. Those units need a converter, which may or may not work with the programming software, so ask before ordering or choose the universal-serial-bus versions - for example ETT-0017 or ETT-0020 with in-system programming. Whichever you choose, ask whether it runs standalone or needs a computer, and if a computer, which operating system, whether the software licence is included and whether the drivers work on your machines.
First, whether you need one: a class does not, because students programme one device each. If your department also runs a production or project workshop, ask how many sockets there are; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether it runs standalone from a stored image; and whether sockets can be replaced individually.
The design software. ETT-0034 to ETT-0038 comprise a field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For each kit, ask which tool and version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. For the simulator, ask what it simulates, which language and version, how many seats, and the licence terms. For kits named after a commercial device family, ask who manufactures and supports them.
Possibly, so compare before ordering. ETT-0026 to ETT-0032 are seven testers - three handheld digital testers, an analogue tester and three universal testers - and the IC Tester and Digital IC Tester listing carries the same instruments under another code series. Remember that they test function against a stored library, not data sheet parameters, so a passing device can still be out of specification and a re-marked part can read as good. ETT-0039 to ETT-0041 share one name; ask what distinguishes them and compare against Embedded System Trainers, which names the processor families.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Every specification, including the supported device list, socket, interface, software licence and throughput, is confirmed in writing on the quotation; ask for the device list as a document rather than a count. For certificates, contact us for the latest copies of the relevant certificates. No price is quoted here. Listing defects noticed: the category is named Training Tools but holds no hand tools; ETT-0013 and ETT-0014, ETT-0024 and ETT-0025, and ETT-0039 to ETT-0041 share names; ETT-0004 and ETT-0006 have truncated names; ETT-0033 is listed only as Experiments; product titles rely on superlatives rather than specifications; and the IC testers also appear in the IC Tester and Digital IC Tester listing under another code series.
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER TO SLAVE. Can program EPROM, EEPROM, FLASH MEMORY & MICRO-CONTROLLERS PC interface through Serial (RS-232) port Interface software supports Win9x/XP/NT/ME/2000 16 x 2 LCD Display (backlit) 4 keys to perform Program, Verify, Blank Check, Lock, Erase, Checksum & Select. Supply voltage: +9V, 600mA from DC Adapter Device update possible DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc. MPU: Atmel, Intel, Microchip, Philips, SST, Winbond, Signetics, Syncmos, Motorola etc. PLD: Atmel 16/20/22 Series.
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER to SLAVE Supports EPROM, EEPROM & FLASH MEMORY Other features are same as of SPROG-VXC DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc..
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER to 4 SLAVES at a time. Supports EPROM, EEPROM & FLASH MEMORY Best suited for mass production of VCD/DVD/PCO/TV etc. PC interface through Serial (RS-232) Port Interface Software supports Windows 9x/XP/NT/ME/2K 16 x 2 LCD Display (backlit) 4 keys to perform Program, Verify, Blank Check, Lock, Erase, Checksum & Select. Supply voltage: +9V, 600mA from DC Adapter Device update possible DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc..
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER to 8 SLAVES at a time. Supports EPROM, EEPROM & FLASH MEMORY Best suited for mass production of VCD/DVD/PCO/TV etc. PC interface through Serial (RS-232) Port Interface Software supports Windows 9x/XP/NT/ME/2K 16 x 2 LCD Display (backlit) 4 keys to perform Program, Verify, Blank Check, Lock, Erase, Checksum & Select. Supply voltage: +9V, 600mA from DC Adapter Device update possible DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc..
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER to 8 SLAVES at a time. Supports EPROM, EEPROM, FLASH MEMORY & MICRO-CONTROLLERS Best suited for mass production PC interface through Serial (RS-232) Port Interface Software supports Windows 9x/XP/NT/ME/2K 16 x 2 LCD Display (backlit) 4 keys to perform Program, Verify, Blank Check, Lock, Erase, Checksum & Select. Supply voltage: +9V, 600mA from DC Adapter Device update possible DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc. MPU: Atmel, Intel, Microchip, Philips, SST, Winbond, Signetics, Syncmos, Motorola etc. PLD: Atmel 16/20/22 Series.
Equipment for Education, Engineering and Vocational Training - FEATURES Copying facility from MASTER to 8 SLAVES at a time. Supports Microchip PIC devices Best suited for mass production PC interface through Serial (RS-232) Port Interface Software supports Windows 9x/XP/NT/ME/2K 16 x 2 LCD Display (backlit) 4 keys to perform Program, Verify, Blank Check, Lock, Erase, Checksum & Select. Supply voltage: +9V, 600mA from DC Adapter Device update possible DEVICE SUPPORT: EPROMs: AMD/MMI, Atmel, Intel, NEC, NS, ST, Holtek, Macronix, SST, Winbond, MTP etc. EEPROM/FLASH: AMD, Atmel, Winbond, Intel, SST, SyncMos, Linkage, Macronix, ST, Dallas, EON, LinkSmart, Mosel_Vitelic, PTC, AST, PMC, AMIC, BenchMarq etc. SERIAL EEPROM: Atmel, ST, AKM, ROHM, ISSI etc. MPU: Atmel, Intel, Microchip, Philips, SST, Winbond, Signetics, Syncmos, Motorola etc. PLD: Atmel 16/20/22 Series.
Equipment for Education, Engineering and Vocational Training - FEATURES Support devices with Vcc from 1.2V to 5V. Extremely fast speed. Built with 48 universal pin-drivers. PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. ISP/ICP programming capability available via ISP/ICP adaptor. Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability. Advanced and powerful functions. Production mode start chip operation at the moment the chip is inserted in the socket properly. Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step. Password can be set for project files and production volume control Batch command combines device operations like program, verify, security into a single command at any sequence. Serial numbers generators are available as standard or customer-specific functions. Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/Vista compatibility Device Updates: XELTEK updates software and device algorithm regularly. View the latestDevice List . Download the current software version free of charge . Updates are available by mail at a nominal charge. XELTEK also adds devices upon customer’s request at its option. Accessories: Main unit with a DIP48 adaptor, AC adaptor, USB2.0 cable, software CD (include: install software, user manual), register card Optional accessories: adaptor in varies packages..
Equipment for Education, Engineering and Vocational Training - FEATURES 6"/9" UV Tube providing UV Light of 2735 degree wave length Mechanical timer for 60 minutes to set time Can erase 8-10 EPROMs at a time within 10-15 minutes 230V, 50Hz mains operation EPROMs of 2716, 2732, 2516, 2532, 2764, 27128, 8755 etc.
Equipment for Education, Engineering and Vocational Training - FEATURES Support devices with Vcc from 1.2V to 5V. Extremely fast speed. Built with 48 universal pin-drivers. PC hosted mode and stand-alone mode. Under PC hosted modes the programmer is controlled by a PC via USB2.0 (high speed) to program a chip. Under stand-alone mode the programmer is controlled via the keypad and the LCD display. A CF card is used to store the project files. User can operate multiple units to construct a concurrent multiprogramming system thank for the stand-alone mode. ISP/ICP programming capability available via ISP/ICP adaptor Only IC manufacturer approved programming algorithms are used for high reliability.±5% and ±10% Vcc verification enhances programming reliability. Advanced and powerful functions. Production mode start chip operation at the moment the chip is inserted in the socket properly. Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step. Password can be set for project files and production volume control. Batch command combines device operations like program, verify, security into a single command at any sequence. Serial numbers generators are available as standard or customer-specific functions. Log file is useful for quality tracking. Over-current and over-voltage protection for safety of the chip and programmer hardware. WINDOWS XP/VISTA compatibility Device Updates: XELTEK updates software and device algorithm regularly. View the latestDevice List . Download the current software version free of charge . Updates are available by mail at a nominal charge. XELTEK also adds devices upon customer’s request at its option. Accessories: Main unit with a DIP48 adaptor, AC adaptor, USB2.0 cable, user manual, software CD, register card Optional accessories: adaptor in varies packages, CF card for stand-alone operation..
Equipment for Education, Engineering and Vocational Training - FEATURES ? Programs high-density Flash memory devices at near theoretical minimum programming times (Program+verify INTEL28F320W18, 32Mb less than 13.5s) Device Support: ? EPROM, Paged EPROM, Parallel and Serial EEPROM, FPGA Configuration Serial PROM, FLASH Memory (NOR and NAND), BPROM, NVRAM, SPLD, CPLD, EPLD, Firmware HUB, Microcontroller, MCU, Standard Logic. Package Support: DIP, SDIP, PLCC, JLCC, SOIC, QFP, TQFP, PQFP, VQFP,TSOP, TSOPII, SOP, PSOP, TSSOP, SON, EBGA, FBGA, VFBGA, µBGA, CSP, SCSP etc. Standard 48 pin universal pin-drivers in universal package. No adapters are needed for DIL devices. Universal pin-drivers are expanded to 100 pins by replacing the standard DIL48 module with PEP3000 module. Local Storage Media through PCMCIA Slot, Compact FLASH Card (Optional) Standard Package: Main unit, DIL 48 Module, AC Adapter, CD-ROM, User's Guide, USB Cable Optional Accessories: PEP3000 Pin-driver Expansion Pack, Package Adapter, CF Card Advanced hardware features minimized Bounce noise. Only IC manufacturers approved algorithms are adopted. Supports 50,000+ devices from up to 100 IC manufacturers including MEMORY, MCU, PLD. Free life-time software update. Three working modes: PC-hosted mode via USB port for R&D, Stand-alone mode for production, Terminal mode for customer application. Pin continuity and wrong chip insertion check prevent chips from accidental damage. Over-current and over-voltage protection for programmer hardware. Clustering programming system, a characteristic volume production solution. Several units work together in stand-alone mode like a multi-site production programmer. Advantages over traditional gang programming: No special gang adapter and s/w are needed. Supports more devices and algorithms update more quickly. Meets budget flexibly. Starts with a single unit, then, add more to increase throughput with business growing. Safer for the production chain because a single unit faulty will not stop whole production. Higher throughput. Each unit starts working as soon as a new chip is inserted, No need for synchronous start of all the units. Programs and Verify 32MB Flash Memories within 18 Seconds Up to 100 Pins Universal Pin-drivers Supports 50,000+ Devices including 1.5V devices High Programming Quality PC Hosted (USB), Stand-alone and Terminal Three Modes in One Unit Powerful and Intelligent Software Operator friendly control software combines many powerful functions with ease of use. Down to 1.5V low voltage devices are supported directly. Software supports WINDOWS 98/ME/NT/2000/XP..