Quick answer. Decide first whether you are equipping teaching benches or a production bay, because that decides single-socket against gang programmer. Students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit; the eight gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025) earn their place where a department also turns out batches in a production or project workshop. Then choose by device list and interface, not by name: the superlatives in these titles - ultra-high, ultra-fast, advanced, handy - are not specifications.
Forty-one items are listed here, ETT-0001 to ETT-0041. Despite the category name there are no hand tools in it. What it actually contains is four quite different things: device programmers, which are the bulk of it, integrated circuit testers, programmable-logic trainer kits and embedded trainers. Several items share identical names, and the fuller listings for three of the four groups are elsewhere on this site, so the table below says where to look as well as what is here.
| Group | Codes | Fuller listing on this site |
|---|---|---|
| Single-socket programmers, microcontroller and memory | ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021 | EPROM Programmer and Programmer Tester |
| Gang programmers, several devices at a time | ETT-0013 to ETT-0016, ETT-0022 to ETT-0025 | Only here |
| Ultraviolet eraser | ETT-0018 | EPROM Programmer and Programmer Tester, where the ultraviolet safety requirements are set out in full |
| Integrated circuit testers | ETT-0026 to ETT-0032 | IC Tester and Digital IC Tester |
| Programmable-logic trainer kits and a simulator | ETT-0034 to ETT-0038 | VLSI Design Training Systems |
| Embedded trainers | ETT-0039, ETT-0040, ETT-0041, all three under the same name | Embedded System Trainers |
| Named only as a word | ETT-0033, listed as "Experiments" | Ask what it is |
Fourteen single-socket programmers are listed under names built largely on superlatives, ultra-high, ultra-fast, advanced, handy. None of those is a specification. Send the supplier the list of parts your laboratory actually programmes and ask for written confirmation, part by part, plus:
Eight codes here are gang programmers, which hold several devices and programme them together. They exist for small-batch production, where the cost per programmed part matters, and they are the one group in this listing with no fuller counterpart elsewhere on the site. Before buying one for a teaching laboratory, be clear that a class does not need one: students programme one device each at their own bench, so one or two single-socket programmers usually serve a laboratory better than one gang unit. A gang programmer earns its place where a department also runs a production or project workshop turning out batches.
If that is your case, ask: how many sockets; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether the unit runs standalone from a stored image, which is what makes it usable by a production operator rather than a programmer; and whether sockets can be replaced individually, since they wear out with use.
Integrated circuit testers (ETT-0026 to ETT-0032). Seven codes including three handheld digital testers, an analogue tester and three universal testers. The important point is what these instruments can and cannot tell you: they test function against a stored library, not data sheet parameters, so a device that passes can still be out of specification, and a re-marked part that happens to pass will read as good. That is set out at length under IC Tester and Digital IC Tester, which also carries the same instruments under another code series; compare the two listings before ordering.
Programmable-logic kits (ETT-0034 to ETT-0038). A field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For all of these the decisive question is the design software: which tool and which version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. The same question, with the reasons, is under VLSI Design Training Systems. For the simulator, ask what it simulates, which language and version, how many seats and what the licence costs each year.
Embedded trainers (ETT-0039 to ETT-0041). All three carry the same name. Ask what distinguishes them and which is current, then compare against Embedded System Trainers, which lists thirty boards with the processor families named.
Quote the code, not the name: ETT-0013 and ETT-0014 carry the same name, ETT-0024 and ETT-0025 carry the same name, ETT-0039 to ETT-0041 all three carry the same name, and two names appear truncated, ETT-0004 ending in "Program" and ETT-0006 in "Serial". Where a code is named after a commercial device family, ask whether the kit is manufactured by Ray Export or supplied as a traded product and who supports it. Ask also for the manual, the supported device list as a document rather than a count, the quantity needed, the supply voltage, frequency and plug type for your country, spare sockets and adapters with prices, and the warranty. For ETT-0018, read the ultraviolet safety requirements before use: the lamp is invisible and gives no warning sensation, the lid interlock must work and must never be defeated, and the unit needs ventilation.
Programming and erasing: EPROM Programmer and Programmer Tester. Device testing: IC Tester and Digital IC Tester. The boards these devices go into: Microprocessor Trainers and Kits, Embedded System Trainers and VLSI Design Training Systems. The bench they are used at: Soldering and Desoldering Stations. Components: Electronic Components. Instruments: Testing and Measuring Lab Trainers. Parent range: Training Kits.
Send your device list and say whether you are equipping benches or a production bay, since that decides single-socket against gang. For example two universal-serial-bus programmers with in-system programming (from ETT-0017 or ETT-0020), with the device list, the update policy and the software licence confirmed in writing. Contact Ray Export for prices, device lists and lead times.
Despite the name, there are no hand tools. ETT-0001 to ETT-0041 cover single-socket programmers (ETT-0001 to ETT-0012, ETT-0017, ETT-0019 to ETT-0021), gang programmers (ETT-0013 to ETT-0016, ETT-0022 to ETT-0025), an ultraviolet eraser (ETT-0018), integrated circuit testers (ETT-0026 to ETT-0032), programmable-logic kits and a simulator (ETT-0034 to ETT-0038) and three embedded trainers (ETT-0039 to ETT-0041). ETT-0033 is listed only as Experiments, so ask what it is. For every group except the gang programmers, a fuller listing exists elsewhere on this site, so compare before ordering.
Ignore the adjectives and send the list of parts your laboratory actually programmes, asking for written confirmation part by part. Then ask how the device library is updated and whether updates are free and for how long; the socket pin count (one code names a 144-pin socket, the others do not) and the adapters for surface-mount packages; whether in-system programming through a header is supported and the cable included; and, where speed is claimed, a figure in seconds for a full programme-and-verify cycle on a named device. Ask too whether the unit can set lock bits, which is often irreversible.
Not directly. Several codes here are serial-port programmers, including ETT-0002, ETT-0004 and ETT-0006, and current computers do not have serial ports. Those units need a converter, which may or may not work with the programming software, so ask before ordering or choose the universal-serial-bus versions - for example ETT-0017 or ETT-0020 with in-system programming. Whichever you choose, ask whether it runs standalone or needs a computer, and if a computer, which operating system, whether the software licence is included and whether the drivers work on your machines.
First, whether you need one: a class does not, because students programme one device each. If your department also runs a production or project workshop, ask how many sockets there are; whether all sockets programme concurrently or in sequence, which is the difference between a genuine gang programmer and a convenience fixture; whether each socket verifies independently and reports its own pass or fail, so one bad part is identified rather than the whole batch rejected; the throughput for a named device; whether it runs standalone from a stored image; and whether sockets can be replaced individually.
The design software. ETT-0034 to ETT-0038 comprise a field-programmable gate array kit, a complex programmable logic device kit, two kits named after particular device families and a hardware-description-language simulator. For each kit, ask which tool and version the device needs, whether that version installs on your laboratory computers, whether the free edition covers the device, and whether a programming cable and its drivers are included. For the simulator, ask what it simulates, which language and version, how many seats, and the licence terms. For kits named after a commercial device family, ask who manufactures and supports them.
Possibly, so compare before ordering. ETT-0026 to ETT-0032 are seven testers - three handheld digital testers, an analogue tester and three universal testers - and the IC Tester and Digital IC Tester listing carries the same instruments under another code series. Remember that they test function against a stored library, not data sheet parameters, so a passing device can still be out of specification and a re-marked part can read as good. ETT-0039 to ETT-0041 share one name; ask what distinguishes them and compare against Embedded System Trainers, which names the processor families.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Every specification, including the supported device list, socket, interface, software licence and throughput, is confirmed in writing on the quotation; ask for the device list as a document rather than a count. For certificates, contact us for the latest copies of the relevant certificates. No price is quoted here. Listing defects noticed: the category is named Training Tools but holds no hand tools; ETT-0013 and ETT-0014, ETT-0024 and ETT-0025, and ETT-0039 to ETT-0041 share names; ETT-0004 and ETT-0006 have truncated names; ETT-0033 is listed only as Experiments; product titles rely on superlatives rather than specifications; and the IC testers also appear in the IC Tester and Digital IC Tester listing under another code series.
Equipment for Education, Engineering and Vocational Training - Embedded Trainer has been designed by using Microchip PIC16F84 Microcontroller. This controller provides in-system as well as in circuit programming so that one may be able to write program and download directly in the controller through serial port without removing it from the system. CPU: Microchip PIC16F84 Microcontroller 16x2 LCD module ? Six Seven Segment Displays 8x8 LED Matrix Display ? EWSN Status LED's 12 Nos. ADC/DAC Interface ? Four Data Switches Switch Array ? At24C16 Serial EEPROM Stepper Motor Controller Interface Only 35 single word instructions to learn All instructions single cycle except for program branches which are two-cycle Operating speed: DC - 20 MHz clock input , DC - 200 ns instruction cycle 1024 words of program memory 68 bytes of data RAM ? 64 bytes of data EEPROM 8-bit wide data bytes ? 14-bit wide instruction words 15 special function hardware registers Eight-level deep hardware stack Direct, indirect and relative addressing modes Four interrupt sources: External RB0/INT pin TMR0 timer overflow PORTB<7:4> interrupt on change Data EEPROM write complete 13 I/O pins with individual direction control High current sink/source for direct LED drive 25 mA sink max. per pin 25 mA source max. per pin TMR0: 8-bit timer/counter with 8-bit programmable prescaler.