Quick answer. Almost every buying mistake in this category comes from the same misreading of what these instruments do. An analytical instrument is a comparison, not a reading. A pH meter, a photometer, a spectrophotometer and a titrimeter all report how a sample differs from a standard - a buffer, a blank, a calibration solution, a reference beam. The instrument supplies the precision; the standard supplies the accuracy, and only one of those two appears on a specification sheet. So the questions that decide whether you get usable numbers are about standards, consumables and calibration intervals, not about the number of digits on the display. Two honest notes: the consumables usually cost more than the instrument over its life, and about half of this listing is not analytical instruments at all - the second half is ovens, autoclaves, furnaces and materials-testing machines. Both are set out below.
A meter that displays 0.01 pH is not accurate to 0.01 pH. It is precise to 0.01 - it will give you the same wrong answer repeatedly - and its accuracy is set by how it was calibrated and by the condition of its electrode. A department that buys on displayed resolution and calibrates with a single buffer once a term is reading three digits of which one is meaningful.
Four rules follow, and they apply across the whole category:
| Instrument | Compared against | Consumable that limits it | The question to ask |
|---|---|---|---|
| pH meter | Buffer solutions at two or three points | The glass electrode, and its reference junction | Electrode type, service life, cost, and whether buffers are supplied |
| Conductivity / TDS / salinity meter | A standard KCl solution of stated conductivity | The cell, and its cell constant | The cell constant, how it is redetermined, and the temperature compensation method |
| Dissolved oxygen meter | Air-saturated water, or a zero solution | Membrane and electrolyte (optical sensors differ) | Membrane replacement interval and whether spares and electrolyte are included |
| Turbidity meter | Formazin or equivalent turbidity standards | The standards themselves, which have a shelf life | Which standard set is supplied and its expiry |
| Photo colorimeter | A blank, plus a calibration curve you build | Filters or LEDs, and the cuvettes | Available wavelengths, and whether a curve-fitting facility is provided |
| UV-VIS spectrophotometer | A blank in a matched cell; the reference beam on a double-beam unit | Deuterium and tungsten lamps; quartz cuvettes for UV | Spectral bandwidth, lamp hours and cost, and whether quartz cuvettes are included |
| Flame photometer | Standard solutions of each element measured | Interference filters, fuel gas and air | Elements covered, gas type and supply, and the extraction requirement |
| Karl Fischer titrimeter | A water standard, used to determine the reagent titre | The reagent, and the drying tube desiccant | Reagent supply and cost, and whether the titre standard is included |
| Potentiometer / ion meter | Standards of the ion being measured | The ion-selective electrode | Which ions, electrode life, and known interferences |
| Water and soil analysis kit | Printed or liquid colour comparators | Reagents, with an expiry date | Whether readings are visual or photometric, and reagent shelf life |
Wavelength range is the figure everyone compares and the figure that almost never decides anything, because every instrument in this class covers the range ordinary work needs. Two other specifications do decide things:
The trap: cuvettes. Ordinary glass and most plastics absorb strongly in the ultraviolet, so UV work needs quartz cells. Quartz cuvettes are frequently not included with a UV-VIS instrument, and a matched pair can cost a noticeable fraction of a modestly priced spectrophotometer. Ask in writing how many cells are supplied, in what material, and whether they are matched - otherwise the instrument arrives unable to do the half of its range you bought it for. Ask also for the wavelength accuracy check method, so the instrument can be verified in-house rather than only believed.
A flame photometer is the cheapest route to sodium, potassium, lithium and calcium determinations, and it is the instrument most often installed without planning for what it needs.
A Karl Fischer titrimeter does not measure water directly against an internal scale; it measures how much reagent a sample consumes, and the reagent's strength - its titre - is determined by titrating a known water standard and then drifts as the reagent ages and takes up atmospheric moisture. Three consequences for the purchase:
We would rather state the position than let a buyer discover it. This listing holds 50 records, AI-0001 to AI-0050, and only about the first twenty-four are analytical instruments. From AI-0025 onward it becomes something else: bacteriological and BOD incubators, a bottle washing machine, a bulk density apparatus, a calibration bath, water baths, an environmental chamber, a fume hood, a heating mantle, three autoclaves, two hot air ovens, two hot plates, a humidity oven, a muffle furnace, a polishing machine, a bench magnifier, a Jominy end-quench hardenability tester, an abrasion tester for glazed tiles and a modulus-of-rupture testing machine.
Those are real products, but they are sterilising, heating and materials-testing equipment, and a buyer looking for an analytical instrument will not expect them here while a buyer looking for an autoclave will never find them. Specifically:
So tell us the determination rather than the code. Say what you need to measure, in what matrix, to what accuracy, and whether the work is teaching or routine testing, and we will quote the current model against that, name every consumable and its cost, and confirm the specification in writing. We have recommended internally that this listing be reduced to analytical instruments, the duplicate deleted, the model names made to state what distinguishes them, and the heating, sterilising and materials-testing records moved to the categories above.
Within physics lab for engineering students: thermodynamics, heat transfer lab equipment, hydraulics and shared engineering lab instruments. For the meters and photometers in their own categories see conductivity and dissolved oxygen meters and TDS, photo colorimeter and flame photometer. The full engineering lab equipment category lists the rest.
Not by itself. The extra digit is resolution, which is repeatability, not accuracy. Accuracy comes from calibration and from the electrode's condition: a 0.01 instrument calibrated with one buffer, on an electrode two years past its useful life, is less accurate than a 0.1 instrument calibrated at three points on a fresh electrode. Buy on calibration facilities, electrode quality and buffer provision, and treat the display resolution as the last tiebreaker.
Two is the minimum, three is better, and they must bracket the range of your samples - a pH meter calibrated at 7 and 4 is not calibrated for a sample at 9. Buffers and standards are inexpensive relative to the instrument, so specify the set that covers your actual working range rather than the pair that happens to be supplied, and ask how often the instrument itself prompts for recalibration.
For any work below roughly 340 nm, yes, because glass and most plastics absorb strongly in the ultraviolet. The point to watch is commercial rather than technical: quartz cells are often not included, and a matched pair can cost a noticeable fraction of a modestly priced instrument. Ask in writing how many cells are supplied, in what material, and whether they are matched - otherwise the instrument arrives unable to do the part of its range you bought it for.
Fuel gas and air, and extraction. Confirm the gas type, regulator and connection, whether a compressor is included, where the cylinder will stand, and what flue or extraction is required - in a teaching building that is a safety approval as well as a plumbing job. Then plan the sodium routine: sodium is in glass, fingerprints, dust and tap water, so credible sodium work needs leached or plastic glassware, deionised water, fresh standards and blanks between samples.
Because the reagent is the method. The instrument measures how much reagent a sample consumes, and the reagent's titre has to be determined against a water standard and redetermined as the reagent ages and absorbs atmospheric moisture. Ask whether the water standard is supplied, how often titre determination is required, what the reagent costs and where it is sourced, and how the cell septum and drying tube keep room humidity out.
Because the listing has been used as a catch-all. Only about the first twenty-four of its fifty records are analytical instruments; the rest are incubators, baths, ovens, autoclaves, a furnace, a fume hood and several materials-testing machines. They are real products in the wrong place, and we have said so here rather than leaving you to scroll. Tell us the determination you need and we will quote against that; the heating and sterilising equipment is linked above in its own category.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
This page gives specification guidance and quotes no prices; prices depend on model, consumables, certification and destination, and are issued only as dated written quotations. Accuracy and repeatability figures, calibration methods, spectral bandwidth, beam configuration, lamp and electrode service lives, cuvette material and count, gas and extraction requirements, reagent supply and all services will be confirmed in writing on the quotation before order. The approximately 340 nm figure for the glass ultraviolet cut-off is a general working guide, not a specification of any product, and the exact cut-off depends on the glass or plastic used - confirm the cell material against your lowest working wavelength. Record counts, the duplicate record, the misspellings and the category misplacements described above were read from this listing on 16 October 2026 and will change as it is corrected.
It is Used
to maintain in water the Marshal specimens to be tested at 600Â+ 10 or
37.80+ as prescribed by the specifications. The Same Water bath can
also be used for the Penetration test, Stripping test or even soundness
test of cement with the use of additional accessories.
This
equipment comprises of a water bath made of perspex sheet with
transparent at the top, fitted with a thermostatic control, maintains
the temperature of water 37 deg. C. Covered vessel 1000 ml made of best
material glass. Provided with variable speed motor.
This apparatus consist of a double
walled, interior chamber made up of stainless steel, an outer body made of CRC/G.I
Friability Test Apparatus is Used
for tablets to determine the durability at the time of production. A
transparent plastic perspex drum with cover also a shaped radial fixed
blade which carries the tablets along with it to the central height and
lets them off while the drum is rotating, thus the tablet rub against
each other without any hard impact.
It consist of 3 heating control and energy regulator. Maximum Temperature of 450° C. Capacity : 50ml, 100ml, 250ml, 500ml, 1 Liter, 2 Liter, 3 Liter, 5 Liter, 10 Liter, 20 Liter, 50 Liter, 100 Liter, 200 Liter.
Fully
automatic vertical autoclave and Industrial Autoclave with
international quality standard. This vertical autoclave is designed to
meet the requirements of sterilization procedures and is perfect for
clinics, hospitals, research laboratories and educational institutes.
This vertical autoclave is made of double walled units.
Portable autoclaves comes with various safety measures and you will experience an easy and safe operation even in tough conditions. These units come with an international quality heating element and can be operated with 220V power supply.
Cement
Autoclave is made of double walled units. The outer chamber is
constructed with thick high-grade sheet duly pre-treated with primers
and painted with stove enamel or powder coated ensuring long-lasting and
rustproof performance. The inner cylinder is made of heavy gauge welded
steel sheet. These cement autoclaves are air insulated form inside and
in some cases as per customer requirement
The
hot air oven is designed to hold in heat and reduce energy output. The
external case of this unit is made of metal with pre-treated with
primers and painted with stove enamel or powder coated, delivering rust
proof and long lasting performance. The inner case is made of
high-quality stainless steel of S.S.304 grade.
Login
Register
+91 9817319615
