Quick answer. Settle the chemicals, the emergency services and the waste route before you choose a reactor. Every CRELE unit is a chemical plant in miniature, and a laboratory with the rigs but not the provisions will not run one experiment. Ask for each experiment's chemical list with quantities per run and confirm the reagents can be bought or imported where you are, because a reactor you cannot charge is furniture. Provide fume extraction ducted outside, an eyewash and drench shower, and a properly sized spill kit, and agree in writing where each vessel's contents go after every run. Then choose reactors by syllabus.
About seventy units, coded CRELE-0001 onwards - the second largest listing in this group. Reactors: batch, adiabatic batch, enzyme, combined flow, a cascade, emulsion and condensation polymerization reactors, a trickle bed and chemical reactor training equipment. Mass transfer and separation: absorption in a packed column, a gas absorption column, solid-liquid extraction, a rapid extractor, sedimentation studies, distillation and a double water distiller, and reverse osmosis with ultrafiltration. Transport and hydrodynamics: fluidisation and fluid bed heat transfer, hydrodynamics of a trickle bed, and residence time distribution studies in a packed bed. Support equipment: interchangeable glassware, a chiller water bath, a laboratory pasteuriser and a liquid chromatograph.
Three notes on our catalogue text. One record is listed only as "Cover All", which does not identify a product - ask us what it is before ordering it. One reactor record has "batch" misspelled and one is listed simply as "Cascade". One code is missing from the sequence, and the liquid chromatograph is an analytical instrument rather than reaction engineering equipment - chromatography is covered in our gas chromatography listing. Quote the code and the full product name together and ask for a specification sheet for anything whose name does not describe a piece of equipment.
This is the one range in the catalogue where the equipment is the smaller half of what you have to provide. Every unit here is a chemical plant in miniature, and a reaction engineering laboratory that has the rigs but not the provisions below will not run a single experiment. Settle all three before the order, not after delivery.
| Provision | What it means in practice |
|---|---|
| Extraction and emergency services | Fume extraction over any unit handling a volatile or a reaction that evolves gas, ducted outside rather than recirculating; an eyewash and a drench shower within a few seconds walk, tested and recorded; a spill kit sized for the largest vessel in the room; and a fire extinguisher suited to the chemicals in use |
| Reagent supply and importability | Every experiment has a chemical list, and some reagents are controlled, some cannot be imported and some have a short shelf life. Ask us for the chemical list of each experiment with the quantities per run, then check availability locally before buying the rig - a reactor you cannot charge is furniture |
| A waste route | Decide, in writing and before delivery, where the contents of each vessel go at the end of each run. Acidic and alkaline effluent usually needs neutralising; organics, catalysts and heavy metals need collection and a licensed route; and nothing goes to the drain by default. The waste route is a condition of operating the laboratory, not an afterthought |
Ask us for the safety data sheet of any chemical supplied with equipment, and confirm it can be imported into your country before the shipment is made up.
The reactors are the heart of the range, and they are not interchangeable - each exists to show something the others cannot. Choose by the syllabus rather than by price.
The batch reactor gives conversion against time, which is where kinetics is learned: rate constants, order of reaction and the Arrhenius dependence if the temperature can be set and held. Ask how temperature is controlled and how samples are drawn and quenched, because a sample that keeps reacting on its way to the analysis gives a kinetics curve that is wrong in a consistent and convincing way.
The continuous stirred tank and the cascade give steady-state conversion against residence time, and the cascade - tanks in series - shows a class the one result that reconciles the two idealisations: as the number of tanks increases, a cascade approaches plug flow. That is worth a rig on its own.
The tubular and trickle bed reactors introduce the real behaviour of flow through a bed: axial dispersion, channelling, and wetting in a trickle bed. The hydrodynamics unit for the trickle bed is the companion piece and is what makes the reactor results interpretable.
The adiabatic batch reactor needs a paragraph of its own. It is deliberately insulated so that the heat of reaction raises the temperature, which is exactly how a runaway reaction happens in industry, and that is the lesson. So the safety specification matters more here than on anything else in the listing. Ask: what reaction is intended and what its heat of reaction is; what the maximum temperature and pressure of the vessel are and what relief device is fitted and where it discharges; whether there is a temperature trip independent of the controller; and whether the reaction can be stopped quickly - a quench, a dump or a cooling path. Never run an unfamiliar exothermic reaction in an adiabatic rig without a written assessment of the worst case, and never scale up an exercise because "it worked at the smaller size".
The polymerization reactors bring their own two issues: polymerizations are exothermic, often strongly so, and the contents become viscous as they go, which changes both mixing and heat transfer. Ask about the stirrer motor torque and whether it will cope at the end of the run, how the vessel is cleaned afterwards, and what the monomer is - monomers are typically flammable, are supplied with an inhibitor and should be stored and used accordingly.
The residence time distribution study is among the best value items here, because it teaches the difference between what a reactor is supposed to do and what it actually does - short-circuiting, dead zones and channelling - with nothing more than a tracer and a detector. The whole experiment turns on those two things, so ask: what tracer is used and how is it detected - a salt with a conductivity cell, a dye with a colorimeter, or something else; how the pulse or step is injected reproducibly; how the signal is logged, since the shape of the curve is the result and reading it by hand loses the detail; and what the tracer costs and whether it can be discharged.
Much of this equipment is borosilicate glass, which is why a record for interchangeable glassware exists. Two practical points: ask for a spares list and prices for every glass component before you buy the rig, because a laboratory with a broken condenser and a three-month lead time has lost a term; and ask what shielding is provided where glass is under vacuum, under pressure or heated, because glass fails suddenly.
Services: cooling water supply and drain for condensers and the chiller bath, and the water quantity per run, which on a distillation rig is substantial; electrical supply with earth-leakage protection, since water and heaters share these benches; compressed air or vacuum where a unit needs it; and bench space that allows a unit to be reached from both sides. Ask also for the warm-up or settling time of each unit, because a distillation column that takes an hour to reach steady operation will not fit a short practical slot.
Two units in the listing serve a different syllabus and are worth separating in your thinking: the laboratory pasteuriser and the reverse osmosis with ultrafiltration unit are food technology and water treatment equipment rather than reaction engineering, and they are excellent for those subjects. Say which programme you are equipping and we will quote accordingly.
For each unit: the experiments it is designed to deliver and the chemical list for each, with quantities per run; vessel material, capacity, maximum temperature and pressure, and relief and trip devices; how temperature is controlled and recorded; sampling arrangement and whether samples can be quenched; stirrer type, speed range and torque; what is instrumented, with accuracies, and whether data can be logged and exported; glass spares list with prices and lead times; services required - cooling water with flow, drain, power, air, vacuum, extraction volume; waste produced per run and its expected route; safety data sheets for anything supplied; bench space, mass and access; nominal voltage, frequency and plug pattern; and the warranty, commissioning, training and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you tender on it.
Related ranges: process control and instrumentation for the control of these processes, heat transfer lab apparatus for the thermal fundamentals, hydraulics and fluid mechanics trainers for flow measurement, refrigeration and air conditioning for cooling plant, and gas chromatography for analysis. The full set is listed under engineering apparatus. For a quotation, send us your syllabus experiment list and tell us the destination country, the services available in the room and what your institution is permitted to store and discharge - those answers decide which of these seventy units you can actually run.
Three provisions. First, extraction and emergency services: fume extraction ducted outside, not recirculating, over any unit handling a volatile or a gas-evolving reaction; an eyewash and drench shower a few seconds' walk away, tested and recorded; a spill kit sized for the largest vessel; and an extinguisher suited to the chemicals. Second, reagent supply: some reagents are controlled, some cannot be imported and some have a short shelf life, so check them locally first. Third, a written waste route: acid and alkaline effluent usually needs neutralising, organics, catalysts and heavy metals need collection, and nothing goes to the drain by default.
Choose by syllabus, because they are not interchangeable. The batch reactor gives conversion against time, which is where kinetics is learned: rate constants, order of reaction and the Arrhenius dependence if temperature can be set and held. Ask how samples are drawn and quenched, since a sample that keeps reacting gives a consistently wrong curve. The continuous stirred tank and the cascade give steady-state conversion against residence time, and the cascade shows that tanks in series approach plug flow as their number rises. The trickle bed reactor shows dispersion, channelling and wetting, and its hydrodynamics unit makes those results interpretable.
More than anything else in the listing, because it is deliberately insulated so the heat of reaction raises the temperature, which is exactly how a runaway happens in industry. Ask what reaction is intended and its heat of reaction; the vessel's maximum temperature and pressure; what relief device is fitted and where it discharges; whether a temperature trip works independently of the controller; and whether the reaction can be stopped quickly by a quench, a dump or a cooling path. Never run an unfamiliar exothermic reaction in it without a written worst-case assessment, and never scale an exercise up because it worked at a smaller size.
The emulsion and condensation polymerization reactors raise two issues. Polymerizations are exothermic, often strongly so, and the contents become viscous as the run goes on, which changes both mixing and heat transfer. Ask what torque the stirrer motor has and whether it will cope at the end of the run, not just the start, and how the vessel is cleaned afterwards. Ask also what monomer the exercise uses: monomers are typically flammable and are supplied with an inhibitor, so they need to be stored and handled accordingly, and that belongs in your chemical list and storage plan.
Because it teaches a large idea with a small rig: the difference between what a reactor is supposed to do and what it actually does, through short-circuiting, dead zones and channelling, using nothing more than a tracer and a detector. Everything turns on those two, so ask what tracer is used and how it is detected, for example a salt with a conductivity cell or a dye with a colorimeter; how the pulse or step is injected reproducibly; and how the signal is logged, since the shape of the curve is the result and reading it by hand loses detail. Ask whether the tracer can be discharged.
Spares and shielding. Much of this equipment is borosilicate glass, so ask for a spares list with lead times for every glass component before you buy, because a broken condenser with a long lead time can cost a term. Ask what shielding is provided where glass is under vacuum, under pressure or heated, since glass fails suddenly. Then the services: cooling water supply and drain with the quantity per run, which is substantial on distillation; power with earth-leakage protection; compressed air or vacuum where needed; and bench access from both sides. Ask each unit's settling time, too.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Specifications for the CRELE units, including vessel material, capacity, maximum temperature and pressure, relief and trip devices, stirrer torque and instrumentation, are confirmed in writing on the quotation, with safety data sheets for anything supplied. For pressure equipment or other documents, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing note: one record is named only Cover All and identifies no product; one reactor record misspells batch and another is named only Cascade; one code is missing from the sequence; and the liquid chromatograph is an analytical instrument filed in a reaction engineering range.
Stuffed Bed Reactor The setup comprises of a glass segment pressed with Rasching Rings and two sustain tanks. Reactants are nourished to the reactor through fluid merchant, fitted at the base of the segment. Rotameters are given to gauge the individual stream of Chemicals. The stream rate can be balanced by working the needle valves gave on individual Rotameter. The attractive drive pump is utilized for dissemination of encourage. Tests can be taken occasionally from the best outlet of reactor. Weight Regulator and Pressure Gauge are fitted in the compacted carrier Experiments Sponification Reaction contemplates in Packed Bed Reactor To decide the Reaction Rate Constant Utilities Required Water Supply and Drain Instruments, Laboratory Glassware and Chemicals required for examination according to the framework embraced Chemical Reaction Engineering lab hardware manufacturers,exporters and Chemical Reaction Engineering Lab providers
Connect Flow Reactor To a perfect Plug Flow Reactor (PFTR) there is no blending toward stream and finish blending opposite to bearing of stream. Centralization of reactants shifts along the length of reactor yet not spiral way: This set-up is utilized to ponder a non-synergist homogeneous response under surrounding condition. The set up comprises of two nourish tanks through which two reactants are bolstered to the reactor. Rotameters are given to quantify the individual stream of Chemicals. The stream rate can be balanced by working the needle valves gave on separate Rotameter. The attractive drive pump is utilized for dissemination of nourish. A straight tube write reactor kept on a level plane and slanted upward at outlet from where tests are gathered for investigation Experiments Sponification Reaction Study in straight tube Plug Flow Reactor. To decide Reaction Rate Constant Utilities Required Water Supply and Drain Instruments, Laboratory Glassware and Chemicals required for examination according to the framework received Chemical Reaction Engineering lab hardware manufacturers,exporters and Chemical Reaction Engineering Lab providers
Attachment Flow Reactor Coiled Tube Type In a perfect Plug Flow Reactor {PFTP} there is no blending toward stream and finish blending opposite to course of stream. Grouping of reactants shifts along the length of reactor yet not outspread way. If there should arise an occurrence of a curl turbulence is acquainted due with visit alter in course of stream and nearness of auxiliary stream, so a higher estimation of response rate consistent is normal in loop tube compose plug stream reactor. This set-up is utilized to think about a non-synergist homogeneous response under isothermal condition. The set up comprises of two encourage tanks through which two reactants are nourished to the reactor. Rotameters are given to gauge the individual stream of Chemicals. The stream rate can be balanced by working the needle valves gave on separate Rotameter. The attractive drive pump is utilized for course of bolster. It is a helical curl tube compose reactor. Reactants enter at bring down end leaving the highest point of loop from where tests are gathered for examination Experiments Sponification Reaction Study in straight tube Plug Flow Reactor. To decide Reaction Rate Constant Utilities Required Water Supply and Drain Instruments, Laboratory Glassware and Chemicals required for examination according to the framework received Chemical Reaction Engineering lab hardware manufacturers,exporters and Chemical Reaction Engineering Lab providers
RTD Studies In CSTR Real reactors don't fulfill the admired stream designs, back blend stream or fitting stream deviation from ideality can be because of directing of liquid through the vessel, reusing of liquid inside the vessel or because of the nearness of dormant locale or pockets of liquid in the vessel.. To foresee the correct conduct of a vessel as a Chemicals reactor, RTD Of boost reaction strategy is utilized. The setup comprises of one bolster tank through which water is sustained to the reactor. The stream rate can be balanced by working the needle valve and estimated by Rotameter. The attractive drive pump is utilized for flow of bolster. The consistently mixed tank reactor made of Stainless Steel is accommodated understanding the R.T.D. qualities. A syringe is utilized for snoozing the tracer in the C.S.T.R Experiments To plot RTD bend for a CSTR Using beat tracer To decide the Dispersion No Utilities Required Water Supply and Drain Electricity Supply: 1 Phase, 220 V AC, 0.5 kW Instruments, Laboratory Glassware and Chemicals required for investigation according to the framework embraced Chemical Reaction Engineering lab gear manufacturers,exporters and Chemical Reaction Engineering Lab providers
RTD Studies in Plug Flow Reactor Real reactors don't fulfill the romanticized stream designs, back blend stream or fitting stream deviation from ideality can be because of diverting of liquid through the vessel, reusing of liquid inside the vessel or because of the nearness of dormant district or pockets of liquid in the vessel.. To foresee the correct conduct of a vessel as a Chemicals reactor, RTD or boost reaction procedure is utilized. The setup comprises of one encourage tank through which water is bolstered to the reactor. The stream rate can be balanced by working the needle valve and estimated by Rotameter. The attractive drive pump is utilized for course of bolster. It is a helical curl tube write plug stream reactor made up of Stainless steel pipe. Reactants enter at bring down end leaving the highest point of curl from where tests are gathered for examination. For comprehension the RTD attributes, an exceptional game plan to infuse tracer into the lower end of reactor, utilizing a syringe is given Experiments To plot RTD bend for Plug Flow Reactor To decide the Dispersion No Utilities Required Water Supply and Drain Instruments, Laboratory Glassware and Chemicals required for investigation according to the framework embraced Chemical Reaction Engineering lab hardware manufacturers,exporters and Chemical Reaction Engineering Lab providers
We are manufacturers,exporters Chemical Reaction UV Photo Reactor Request Callback.
We are manufacturers,exporters Vapor Liquid Equilibrium Apparatus.
STR (i.e. a perfect consistent state stream reactor) the substance in reactor are all around blended and have uniform organization all through. In this manner the leave stream has an indistinguishable sythesis from the liquid inside the reactor. This sort of reactor is known as blended stream reactor. This set-up is utilized to think about a non-synergist homogeneous second request fluid stage response under encompassing condition.The set up comprises of two sustain tanks through which two reactants are bolstered to the reactor. Rotameters are given to quantify the individual stream of Chemicals. The stream rate can be balanced by working the needle valves gave on particular Rotameter. The packed air is utilized for course of nourish. The CSTR is fitted with stirrer for appropriate blending. From top outlet of it tests are gathered for examination. Weight Regulator, Pressure Gauge and Safety Valve are fitted in the packed aircraft..
CSTR Fixed Bed Reactors discover their application in Petroleum, Petrochemical, Polymer, Pharmaceutical, Specialty Chemical alike enterprises to complete responses like carboxylation, hydrogenation, hydrocracking, hydroformulation, fractional oxidation, polymerization and so on Features : Better Productivity since utilized as a part of ceaseless mode. Weight Range: - upto 100 bar Temperature Range: - upto 1200°C 3 Zone split heater for warming Possibility to interface with GC for examination Completely computerized framework with Scada programming. Ceaseless Flow Stirred Tank Reactors System (CSTR):- CSTR are utilized where there is a nonstop generation or advancement keeping in mind the end goal to expand the profitability. Gases fluids are included consistently in the blended reactor item is recuperated on nonstop premise at high weight temperature. Accessible in sizes from 100ml to 100 Ltr. ContinuousFlowFixed/FluidizedBed Tubular Catalytic Reactor Systems:- Reactant fluids gases are encouraged to a reactor which utilizes a tubular vessel stuffed with a settled bed of Catalyst at controlled rate through pre-radiators pre-blender. Last items are gathered from the outlet of the reactor cooled isolated for recuperation. Included Accessories:- Gas Feed System Liquid Feed System Back Pressure controllers manual or programmed to keep up consistent upstream weight. Condenser for refining/reflux or condensate return back or for cooling. Gas/Liquid separator to isolate the gases from the fluid by gathering the fluid venting the gas. Level Control System Mounting Control System Software.