science lab equipment manufacturer

Cutaways Models

Cutaways Models Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Cutaways Models in India,

Quick answer. Decide the tier before you compare engines: turned, driven or running. CM-0001 to CM-0020 mixes hand-driven cutaways, motor-driven cutaways, cut-section car and jeep chassis, and five engine test rigs. A hand-driven cutaway is the best way to teach valve timing and needs only floor space and good light. A motor-driven one needs a socket and guarding. Only the running test rigs produce brake power, fuel consumption and heat balance figures, and they need exhaust extraction to outside, fuel storage, cooling water and a battery. Buying a rig when a cutaway was wanted is the common and costly mistake.

What this range covers

Twenty units, coded CM-0001 to CM-0020, in three distinct kinds. Cutaway engines: a vertical diesel, two-stroke and four-stroke single-cylinder scooter and motorcycle engines, and four-cylinder petrol and diesel engines in hand-driven and motor-driven versions. Cut-section vehicles: car chassis with a four-cylinder petrol engine, and car or jeep chassis with a four-cylinder diesel engine. Engine test rigs: single-cylinder diesel, twin-cylinder diesel, single-cylinder two-stroke and four-stroke petrol, and a multi-cylinder four-stroke petrol rig.

One note on our catalogue data before you order. Four of these records carry the same product name, distinguished only by a trailing digit, and two more differ only by a space in the text. They are not four identical products; the names were damaged when the catalogue was imported. Ask for the specification of each record you are considering, and have the engine, the drive arrangement and the dimensions confirmed on the proforma invoice.

Turned, Driven, Running

These twenty units sit in three tiers, and the tier decides the price, the services the room must provide and what the equipment can teach. The names tell you which tier each unit is in, and it is the first thing to settle.

TierWhat it doesBest forWhat the room must provide
Turned - hand-driven cutawayA student rotates the crankshaft slowly by hand and watches valves, piston and timing move togetherIndividual and small-group study. The best way there is to teach valve timing, because the student controls the speed and can stop at any point in the cycleFloor or bench space and good lighting. Nothing else
Driven - motor-driven cutawayA slow electric drive turns the engine continuouslyDemonstration to a whole class, and for showing a cycle repeatingA socket, and guarding over the drive and any exposed moving part
Running - engine test rigThe engine runs on fuel and is loaded, so performance can be measuredMechanical engineering laboratory work: power, fuel consumption, heat balance, Morse testExhaust extraction to outside, fuel storage and supply, cooling water, a battery, and a position where noise is acceptable

The common mistake is buying a running rig when a hand-driven cutaway was wanted, usually because a specification said "engine" without saying what the students would do with it. A test rig that cannot be run because the room has no extraction is an expensive display, and a cutaway cannot produce a performance curve.

What makes a cutaway good, and what to ask

A cutaway is a real engine that someone has cut open, and the quality is almost entirely in the cutting and finishing rather than in the engine. Five questions separate a teaching instrument from a damaged engine on a stand.

Are the cut edges finished? Deburred, smoothed and painted or plated. A raw cut edge is a cut hand, and students put their hands on these.

Does it still move freely? Sectioning removes material that guided and supported the moving parts, so a badly cut engine binds or the piston fouls the sectioned bore. Ask for confirmation that the mechanism turns smoothly through a full cycle by hand.

Is it colour-coded and labelled? The best cutaways paint systems in different colours - induction, exhaust, coolant, oil - and supply a labelled diagram or key. Without that, a student sees a complicated metal object; with it, they see a cooling system. Ask whether a chart or key is included and in what language.

Is the engine new or reclaimed, and has it been cleaned? Both are legitimate - a reclaimed engine is often the more realistic teaching object - but a reclaimed engine must be degreased, drained of fuel, oil and coolant, and sealed. Ask for that in writing, because an engine that still weeps oil onto a classroom floor is a complaint nobody anticipates.

What is it mounted on? A stand of the right height, preferably with castors and a locking arrangement, and stable enough that a student can lean on it. Ask the mass and the footprint, and ask whether the stand allows the engine to be rotated for access from below, which is a genuinely useful feature on a single-cylinder unit.

The cut-section chassis: measure your doorway first

A cut-section car or jeep chassis with its engine is the most impressive teaching object in this range and the most awkward to install. Before ordering, establish: overall length, width and height; mass; whether it is delivered in one piece or assembled on site; and the route from the street to the room, measured at the narrowest point. Ask also what remains functional - whether the steering turns, whether the wheels rotate, whether the transmission can be turned over by hand - because that is what separates a chassis a class can work on from one they can only look at.

And since a chassis is a large object a class gathers around, ask about the finish: guards or covers over any pinch point, no raw cut edges at hand height, and a stable stance with the wheels chocked or the frame supported rather than resting on tyres.

The engine test rigs, and the instrumentation that makes them worth buying

The five test rigs are the only units here that produce numbers, and for a mechanical engineering syllabus the numbers are the point: brake power, indicated power, specific fuel consumption, mechanical efficiency and a heat balance. A rig without a means of loading the engine and measuring fuel flow cannot produce any of them. So ask, item by item.

What loads the engine - a rope brake, an eddy current or hydraulic dynamometer, or an electrical generator with a load bank - and how torque and speed are read. How fuel flow is measured, since a burette and a stopwatch is the usual arrangement and a measured volume against time is what gives specific consumption. What temperatures are instrumented, because a heat balance needs inlet and outlet cooling water, exhaust gas and ambient. Whether an air box with an orifice is fitted, since air flow is needed for the air-fuel ratio. Whether a pressure transducer and crank angle encoder are offered, because that is what turns the rig into an indicator-diagram exercise. And for the multi-cylinder rig, whether cylinders can be cut out individually, which is what the Morse test requires.

Then the services, which are not optional: exhaust extraction ducted outside the building - a running engine indoors without extraction is a carbon monoxide hazard and a classroom with the windows open is not extraction; a fuel arrangement whose quantity and storage satisfy your local rules, kept out of the teaching area; cooling water supply and drain; a battery, isolated before anyone works on wiring; and an accepted noise position. Ask for the extraction volume and duct diameter, the cooling water flow and the fuel consumption rate, and have all three provided before delivery rather than after.

What to ask for on the quotation

Which tier each unit is - hand-driven, motor-driven or running; the engine make, type, capacity and number of cylinders; cut-surface finish, colour coding and whether a labelled chart is supplied; confirmation that the mechanism turns freely through a full cycle; whether the engine is new or reclaimed and that it has been drained, degreased and sealed; stand type, castors, locking and whether the unit can be rotated; mass, footprint, packed dimensions and whether it ships assembled; for the test rigs, the loading device, torque and speed measurement, fuel measurement, instrumented temperatures, air measurement and cylinder cut-out; services required - extraction volume and duct size, fuel, cooling water, power, battery; guarding and emergency stop on anything driven; consumables and spares with prices; nominal voltage, frequency and plug pattern; and the warranty, commissioning and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you tender on it.

Related ranges: automobile equipments for components and system models, automotive trainers and models for steering and braking trainers, machines for thermodynamics and power plant apparatus including gas turbines and compressors, the heat transfer lab range for the heat balance side of the subject, and the automobile workshop range for workshop fit-out. The full set is listed under engineering apparatus. For a quotation, tell us the destination country, whether the engines must run indoors, the syllabus you teach and the class size in one practical session.

Frequently asked questions

Should we choose a hand-driven or a motor-driven cutaway engine?

It depends on how you teach. With a hand-driven cutaway a student turns the crankshaft slowly and watches valves, piston and timing move together, and can stop at any point in the cycle, which makes it the best way to teach valve timing to individuals and small groups. It needs only floor or bench space and good lighting. A motor-driven cutaway turns continuously on a slow electric drive, which suits demonstration to a whole class and showing a cycle repeating. It needs a socket, guarding over the drive and any exposed moving part, and an emergency stop.

What separates a good cutaway from a damaged engine on a stand?

The quality is in the cutting and finishing. Ask whether the cut edges are deburred, smoothed and painted or plated, since students put their hands on them. Ask for confirmation that the mechanism turns freely through a full cycle by hand, because sectioning removes material that guided the moving parts. Ask whether systems such as induction, exhaust, coolant and oil are colour-coded with a labelled key, and in what language. If the engine is reclaimed, have it drained, degreased and sealed in writing. Finally, ask about the stand: height, castors, locking and stability.

What should we check before ordering a cut-section car or jeep chassis?

Measure your doorway first. Establish the overall length, width and height, the mass, whether it arrives in one piece or is assembled on site, and the route from the street to the room measured at its narrowest point. Then ask what still works: whether the steering turns, the wheels rotate and the transmission can be turned over by hand, since that separates a chassis a class can work on from one it can only look at. Ask also for guards over pinch points, no raw cut edges at hand height, and a frame supported or wheels chocked rather than resting on tyres.

What instrumentation should an engine test rig come with?

Enough to produce brake power, specific fuel consumption, mechanical efficiency and a heat balance. Ask, rig by rig, what loads the engine (a rope brake, an eddy current or hydraulic dynamometer, or a generator with a load bank) and how torque and speed are read; how fuel flow is measured, usually a burette and stopwatch; and which temperatures are instrumented, since a heat balance needs inlet and outlet cooling water, exhaust gas and ambient. Ask whether an air box with an orifice is fitted, whether a pressure transducer and crank angle encoder are offered, and whether the multi-cylinder rig allows cylinder cut-out for the Morse test.

What services must the room have before a test rig arrives?

Five, and none is optional. Exhaust extraction ducted outside the building, because a running engine indoors without extraction is a carbon monoxide hazard and open windows are not extraction. A fuel arrangement whose quantity and storage satisfy your local rules, kept out of the teaching area. A cooling water supply and drain. A battery, isolated before anyone works on wiring. And a position where the noise is acceptable. Ask for the extraction volume and duct diameter, the cooling water flow and the fuel consumption rate, and have all three provided before delivery rather than after.

Why do some records in this range have the same name?

Four records carry the same product name, distinguished only by a trailing digit, and two more differ only by a space. They are not identical products: the names were damaged when the catalogue was imported. Ask for the specification of each record you are considering, and have the engine, the drive arrangement and the dimensions confirmed on the proforma invoice. Note also that the CM- code prefix is used in another category on this site, where CM-0001 is a different product, so quote the product name alongside the code in any enquiry.

Key takeaways

  • Tier first: hand-driven, motor-driven or running decides what the unit can teach and what the room must provide.
  • Valve timing by hand: a hand-driven cutaway lets the student stop the cycle at any point, which a driven one does not.
  • Finish is the quality: deburred edges, free movement through a full cycle, colour coding and a labelled key separate good cutaways from poor ones.
  • Measure the route: for a cut-section chassis, check dimensions, mass and the narrowest point between the street and the room.
  • Rigs need instruments: without a loading device and fuel measurement there is no brake power, specific fuel consumption or heat balance.
  • Services before delivery: exhaust extraction to outside, fuel storage, cooling water, a battery and an acceptable noise position.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Specifications for CM-0001 to CM-0020, including engine make, capacity, drive arrangement, dimensions, mass and test rig instrumentation, are confirmed in writing on the quotation and on the proforma invoice. If a tender needs certificates, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing note: four records share one product name distinguished only by a trailing digit and two more differ only by a space, damage from the catalogue import; and the CM- code prefix is also used by a different category on this site, where CM-0001 is a different product, so quote the product name with the code when you enquire.

Vertical Diesel Engine For Engineering Schools

CM-0001

Vertical Diesel Engine, technical teaching equipment for engineering

2 Stroke 1 Cylinder Scoter Engine For Engineering Schools

CM-0002

 2 Stroke 1 Cylinder Scoter Engine, technical teaching equipment for engineering

2 Stroke 1 Cylinder Motorcycle Engine For Engineering Schools

CM-0003

2 Stroke 1 Cylinder Motorcycle Engine, technical teaching equipment for engineering

4 Stroke 1 Cylinder Scooter Engine For Engineering Schools

CM-0004

4 Stroke 1 Cylinder Scooter Engine, technical teaching equipment for engineering

4 Stroke 1 Cylinder Motorcycle Engine For Engineering Schools

CM-0005

4 Stroke 1 Cylinder Motorcycle Engine, technical teaching equipment for engineering

4 Stroke 4 Cylinder Petrol Engine (Hand Driven) For Engineering Schools

CM-0006

 4 stroke 4 cylinder Petrol Engine (hand driven), technical teaching equipment for engineering

4 Stroke 4 Cylinder Petrol Engine (Motor Driven) For Engineering Schools

CM-0007

4 stroke 4 cylinder Petrol Engine (motor driven), technical teaching equipment for engineering

4 Stroke 4 Cylinder Diesel Actual Engine (Hand Driven) For Engineering Schools

CM-0008

4 stroke 4 cylinder Diesel Actual Engine (hand driven), technical teaching equipment for engineering

4 Stroke 4 Cylinder Diesel Engine (Motor Driven) For Engineering Schools

CM-0009

4 stroke 4 cylinder Diesel Engine (motor driven), technical teaching equipment for engineering

Actual Cut Section Car Chassis 4 Stroke 4 Cylinder Petrol Engine For Engineering Schools

CM-0010

 Actual Cut Section Car Chassis 4 stroke 4 cylinder Petrol Engine, technical teaching equipment for engineering

Supply of Cutaways Models from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }