science lab equipment manufacturer

NDT Metal-Testers

NDT Metal-Testers Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of NDT Metal-Testers in India,

Portable Hardness Testers and NDT Instruments

Quick answer. The thing to understand before buying any portable hardness tester is that none of them measures hardness. A rebound instrument measures the velocity ratio of a small impacting ball; an ultrasonic contact impedance instrument measures the frequency shift of a loaded diamond-tipped rod. Each then converts that measurement into a Brinell, Rockwell or Vickers number through a table that depends on the material group. So a portable reading quoted in HRC is a converted estimate, and it is only valid if the conversion matches the material. Everything else that decides whether you get usable numbers follows from this: the specimen mass and surface finish, the impact direction, the probe type, and a calibrated test block to verify against. Two notes on this listing: roughly half of it tests concrete rather than metal, and several records carry third-party instrument brand names - see the note below before ordering by code.

The framework: the instrument measures one thing and reports another

A bench hardness tester presses a defined indenter with a defined force and measures the indentation - that is a direct measurement, and it is why bench testers remain the reference. A portable instrument cannot carry that load frame into the field, so it measures a dynamic or acoustic proxy instead and converts. Understanding which proxy decides what the instrument can and cannot do.

MethodWhat it measuresSuitsIts main limitation
Rebound (dynamic) hardnessThe ratio of rebound velocity to impact velocity of a spring-propelled ballLarge, heavy, solid parts; castings, forgings, shafts, weld areasNeeds a minimum specimen mass and thickness, and is sensitive to impact direction. Reads low on anything that can move or ring.
Ultrasonic contact impedanceThe frequency shift of a vibrating diamond-tipped rod pressed into the surfaceThin walls, small parts, gear teeth, tight spaces, thin coatings on a hard baseNeeds a smoother, cleaner surface than rebound, and a steady hand or a stand to apply the load consistently.
Bench indentation (for reference)The indentation itself, under a defined loadLaboratory work and anything that must be reported as a measured valueNot portable. See hardness testing machines.

The practical rule that follows: if a result has to be defensible as a measured hardness - for a certificate, a dispute, an acceptance test - it should be made on a bench tester. Portable instruments are for screening, for sorting, for checking a heat treatment across a large component, and for the many cases where the part cannot be cut or carried. Both are legitimate; confusing them is not.

The four specifications that decide whether the numbers are usable

1. The conversion, and the material group

Ask which scales the instrument converts to, and which material groups its conversion tables cover - typically steel and cast steel are treated separately from cast iron, stainless, aluminium alloys, brass and bronze. Using a steel table on cast iron produces a confident wrong answer. Ask also whether a user-defined conversion can be entered, because for an unusual alloy the correct procedure is to establish your own correlation by testing reference pieces on a bench tester and on the portable instrument, and an instrument that cannot store that correlation forces the correction to be done by hand every time.

2. Specimen mass, thickness and coupling

For a rebound instrument this is the specification that is ignored most often and matters most. The method assumes the specimen does not move or ring when struck. Below a minimum mass the part recoils and absorbs energy, and the reading comes out low - sometimes dramatically. Below a minimum thickness the surface flexes, with the same effect. The remedies are standard practice:

  • Clamp or couple a light part to a support mass, with a thin layer of coupling paste, so that the assembly behaves as one heavy body.
  • Or use the ultrasonic method instead, which loads the surface statically and is far less sensitive to the part's mass - which is exactly why both methods exist.

Ask for the minimum mass and thickness figures for each probe you are quoted, and check them against the thinnest and lightest part you actually test, not the average.

3. Impact direction, surface finish and probe type

  • Impact direction. A rebound instrument works against gravity, so a measurement taken upwards does not match one taken downwards unless the instrument compensates. Ask whether direction compensation is automatic or must be selected, because a selected setting is a setting that gets forgotten.
  • Surface finish. Both methods need the surface prepared - scale, paint, rust and machining ridges all shift the reading. Ask what finish the method requires, and remember that preparing the surface with an abrasive can temporarily work-harden it, which is why light grinding with cooling is preferred to aggressive abrasion.
  • Probe type. Different impact devices exist for different geometries - small radii, grooves, thin sections, hardened surfaces. One probe does not cover a workshop. Confirm which probes are included rather than available.

4. A calibrated test block, and a verification interval

A portable hardness tester is verified against a reference block of certified hardness, and the block is a consumable: its surface wears where it is struck, so readings must be spread and the block eventually retired. So:

  • Ask for the test block with its calibration certificate, in a hardness range near your working range - a block at 60 HRC does not verify an instrument used at 150 HB.
  • Agree a verification interval and write it down, with a simple log kept beside the instrument. An unverified portable tester is an opinion.
  • For rebound hammers used on concrete, the equivalent reference is a calibration anvil, and the same argument applies.

Concrete rebound hammers are a different instrument - and half this listing is them

Several records in this category are rebound test hammers for concrete, which despite the shared word "rebound" are not metal hardness testers at all. A concrete test hammer measures the surface rebound of a spring-driven mass against a concrete surface and reports a rebound number, which is then correlated to compressive strength. Three things a buyer must know:

  • The correlation is not universal. It depends on the mix, the aggregate, the age, the moisture and the carbonation of the surface, so a rebound number converted to strength using the instrument's default curve is an estimate, not a test result. A defensible correlation is established by testing cores from the actual structure alongside hammer readings.
  • It measures the outer few millimetres only. A carbonated or surface-hardened skin reads high while the body of the concrete may be weaker - which is precisely the situation in which someone reaches for the hammer.
  • Different hammer types exist for different impact energies, for light or thin elements against heavy structural members, with recording and digital variants. These type designations are genuine specifications, not cosmetic model names, so match the type to the element you are testing.

If concrete assessment is your purpose, these belong with concrete testing machines and with core testing - see core cutting and preparation for the coring and specimen preparation that a real correlation requires.

The ultrasonic instrument: ask which job it does

"Ultrasonic instrument" covers two different products that are rarely interchangeable, so confirm which is being quoted:

  • A thickness gauge measures remaining wall thickness, typically through paint, on pipes, tanks and plate. It is simple, it needs a couplant, and its specification is the thickness range and the probe frequency.
  • A flaw detector finds and sizes internal discontinuities and weld defects, and it is only as good as its operator - it needs angle probes, calibration blocks, a documented technique and a qualified user. Buying a flaw detector without budgeting for operator qualification produces an instrument nobody is permitted to interpret.

For either, ask for the probes included, the couplant, the calibration blocks, and the battery and charging arrangement for field use.

What a quotation must state

  • Method - rebound, ultrasonic contact impedance, or concrete rebound - stated plainly rather than implied by a model name.
  • Scales converted to, and the material groups the conversion tables cover; whether a user correlation can be stored.
  • Minimum specimen mass and thickness for each probe quoted.
  • Probes included, and the geometries each suits.
  • Direction compensation: automatic or selected.
  • Test block or calibration anvil, its hardness value and its certificate.
  • Required surface finish, and any preparation accessories.
  • For ultrasonic: thickness gauge or flaw detector, probes, frequencies, couplant and calibration blocks.
  • Battery type and life, charger, case, and the data output or printing arrangement if results must be recorded.

About this listing - two things to read before ordering by code

1. The category is named for metal and roughly half of it is for concrete. Of the records on the first page, four are portable metal hardness testers, five are concrete rebound test hammers and their calibration anvil, and one is a general ultrasonic instrument. We have recommended that the concrete records move to the concrete and aggregate ranges, where a buyer looking for them would actually search.

2. Several records carry third-party instrument brand names. Where a named branded instrument is supplied, it is supplied as that manufacturer's product rather than as a Ray Export design, and the listing does not currently make that distinction clear. We have raised this internally for correction. In the meantime, please ask us to confirm in writing exactly what is being offered against your enquiry - the manufacturer, the model and whether it is the branded instrument or an equivalent - because you are entitled to know which you are buying and it changes both the price and the support arrangements.

3. One name is truncated mid-word. One record reads "...Portab for engineering schools Hardness Tester", where the word is "Portable" and a suffix has been spliced into the middle of it. It is a data fault rather than a product fault, and it is flagged for correction, but it is worth knowing if you are searching this listing by name and finding nothing.

So enquire by method and application: say whether the material is metal or concrete, the thinnest and lightest part you test, the scale you need to report in, and whether the result must be defensible as a measurement or is for screening. We will quote the right instrument, name the manufacturer, and confirm the conversion tables, probes, mass limits and certificates in writing.

Related ranges

Parent category: non-destructive testing. For laboratory reference testing see hardness testing machines, metal testing machines and universal testing machines; for concrete and cores, concrete testing machines and rock testing and core preparation; for microstructure behind a hardness result, metallurgical equipment. The full TVET training equipment category lists the rest.

Frequently asked questions

Does a portable hardness tester actually measure hardness?

No. A rebound instrument measures the velocity ratio of an impacting ball; an ultrasonic contact impedance instrument measures the frequency shift of a loaded diamond-tipped rod. Each converts that measurement into Brinell, Rockwell or Vickers through a material-dependent table. So a portable reading in HRC is a converted estimate, valid only if the conversion matches the material group. For a result that must be defensible as a measurement, use a bench tester.

Why does a rebound tester read low on small parts?

Because the method assumes the specimen does not move or ring when struck. Below a minimum mass the part recoils and absorbs impact energy; below a minimum thickness the surface flexes. Either way the rebound is reduced and the hardness reads low, sometimes dramatically. Clamp or couple a light part to a support mass with coupling paste, or use the ultrasonic method, which is far less sensitive to specimen mass.

What should we ask about conversion tables?

Which scales the instrument converts to and which material groups the tables cover, since steel, cast iron, stainless, aluminium alloys and copper alloys are treated separately and using the wrong table gives a confident wrong answer. Ask also whether a user-defined correlation can be stored, because for an unusual alloy the correct procedure is to establish your own correlation against a bench tester.

Do we need a calibrated test block?

Yes, and in a hardness range near your working range - a block at 60 HRC does not verify an instrument used at 150 HB. Ask for the block with its certificate, agree a verification interval, and keep a short log beside the instrument. Note that the block is a consumable: its surface wears where it is struck, so spread the readings and retire it when the surface is used up.

Can a concrete rebound hammer tell us the concrete strength?

It gives a rebound number, and converting that to strength with the instrument's default curve is an estimate rather than a test result, because the correlation depends on the mix, aggregate, age, moisture and surface carbonation. A defensible figure comes from correlating hammer readings against cores taken from the actual structure. Remember also that the hammer reads only the outer few millimetres, so a hardened or carbonated skin can read high over weaker concrete.

Is "ultrasonic instrument" a thickness gauge or a flaw detector?

They are different products and rarely interchangeable, so ask. A thickness gauge measures remaining wall thickness, often through paint, and is specified by thickness range and probe frequency. A flaw detector finds and sizes internal defects and needs angle probes, calibration blocks, a documented technique and a qualified operator - so budget for operator qualification, or the instrument will be one nobody is permitted to interpret.

Key takeaways

  • No portable tester measures hardness - it converts. Check which scales and which material groups, and store your own correlation for unusual alloys.
  • Get the minimum mass and thickness figures per probe, and check them against your thinnest and lightest part, not the average.
  • Use the ultrasonic method for thin and light work, rebound for heavy solid parts. That is why both exist.
  • Buy the certified test block in your working range, and treat it as a consumable with a verification log.
  • A concrete rebound number is not a strength. Correlate against cores from the actual structure, and remember it reads only the surface skin.
  • Ask us in writing which manufacturer and model is being offered, since this listing mixes branded instruments with equivalents and concrete instruments with metal ones.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

This page describes instrument types generically and quotes no prices; prices depend on method, probes, blocks, certification and destination, and are issued only as dated written quotations. Where a record in this category names a third-party instrument brand, that instrument is the product of its own manufacturer and not a Ray Export design; the manufacturer, model and whether a branded instrument or an equivalent is being offered will be stated in writing on the quotation. No brand relationship is claimed on this page. Conversion scales and material groups, minimum specimen mass and thickness, probe coverage, direction compensation, required surface finish, test block values and certificates, ultrasonic probe frequencies and calibration blocks, battery life and data output will be confirmed in writing before order. No test standard is named on this page and no tolerance or conversion figure is quoted, because the applicable standard and the valid conversion differ by country, instrument and material - name the standard you work to and compliance will be confirmed against it rather than assumed. Statements about method limitations are general practice rather than claims about any particular product. The record counts and the truncated name described above were read from this listing on 16 October 2026 and will change as it is corrected.

PROFOMETER 5+ Rebar Detection System For Testing Lab

NDT-0011

PROFOMETER 5+ Rebar Detection System - Location and introduction of strengthening bars. Measuring concrete cover depth. Assurance of bar distance across. Conservative, easy to understand demonstrating gadget with backdrop illumination. ProVista PC programming for quick information exchange and altering.Can be operated in metric and imperial units.

PROFOSCOPE Rebar Detection System For Testing Lab

NDT-0012

PROFOSCOPE Rebar Detection System.

Torrent Permeability Tester For Testing Lab

NDT-0013

Torrent Permeability Tester : The porousness of concrete at the surface (concrete) has been perceived as a main consideration in deciding the toughness of concrete structures. Numerous experts accentuate the significance of this property and the likelihood of measuring it dependably - in the research facility as well as at the building site..

Pull-Off Tester DYNA For Testing Lab

NDT-0014

Pull Off Tester DYNA - Testing is completed specifically on the structure. It can be measured on any purpose of the structure. For the assurance of the tension strength it isn't important to introduce test gadgets before the casting of the concrete. It is perfect for the assessment of quality in concrete renovation. Focal points : 1. Versatile for use in any area 2. Free of mains supply because of simple running wrench drive 3. Steady jolt free load increment.

Portable Hardness Tester

NDT-0015

Depiction: 


It can be utilized for all metals. One can without much of a stretch manage creation level testing. The hardware is most appropriate for on location testing of all size as of now introduced parts. The gadget is most appropriate for material choice and acknowledgment tests. Likewise it is anything but difficult to utilize and exact on bended test surfaces (R>10 mm). This gadget is principally utilized as a part of metal creation and preparing car, Power Plants, transportation hardware, Petro-Chemical Refineries, Aerospace and shipyard Metal Constructions Testing Services and labs. 


Particulars and FEATURES: 


Hardness Tester is very precise ± 4 HL, Easy to peruse show, Light weight, programmed revision for affect course. Change over all normal hardness scales (HV, HRC, HB, HS, HRB, Rm). Huge memory with on-screen audit of information, Ethernet, download to PC or print straightforwardly by means of USB, or RS-232, client profiles for quick difference in all setting, Rugged fixed layer keypad Internal rechargeable batteries or standard "C" cells Custom transformations for unprecedented compounds.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipment, engineering equipments exporters, engineering equipments suppliers, engineering equipments supplier, engineering educational equipments, engineering equipments manufacturers in Ambala, India.


Piccolo Portable Hardness Tester

NDT-0016

Portrayal: 

 Piccolo Portable Hardness Tester is the most progressive coordinated analyzer. It is the new impression gadget with single movement stack and discharge instrument. The hardness analyzer which we give to our clients is exceptionally exact in any effect heading and programmed. It proselytes to all normal hardness scales (HV, HB, HRC, HRB, HS, Rm).It bolsters custom changes for exceptional combinations, Statistics (normal, standard deviation, min/max, go) - Internal, non-unpredictable information stockpiling of completely labeled readings. Encourages moment perusing from substantial, high-differentiate LCD. It has shrewd self analytic element. Energizing of implicit Li-Ion batteries with USB associated, USB information and programming exchange with flexible PC application. 


APPLICATION: 


· Good for all materials 


· Best suited for on location testing of overwhelming, huge or as of now introduced parts 


· Ideal for generation level testing 


· Handy for hard to get to or limited test areas 


· Automatic detecting and remuneration for affect bearing 


· Excellent for material determination and acknowledgment tests 


· Easy to utilize and exact on bended test surfaces (R>10 mm) 


· Primarily utilized as a part of Industries, for example, 


· Metal creation and preparing 


· Automotive and transportation 


· Metal developments Testing administrations and labs. 


· Machinery and power plants Petro-Chemical refineries, 


· Aerospace and shipyard


Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipment, engineering equipments exporters, engineering equipments suppliers, engineering equipments supplier, engineering educational equipments, engineering equipments manufacturers  in Ambala, India.


Portable Hardness Tester

NDT-0017

Depiction: 


Convenient Hardness Tester is straightforward in activity as it can be physically worked. The analyzer provided by Hover labs is quick and precise as we guarantee the quality mind every item we offer to our customers. It is smaller, lightweight and convenient. It shows specifically in Rockwell C scale. 


APPLICATION: 


• Minimum surface layer thickness: 0.7 mm 


• Minimum test range R = 30 mm (1.18 in.) Of surface ebb and flow: 


• Ideal for specialists, mechanical engineers, quality and creation work force with occasional prerequisites for fast and simple hardness estimations in HRC 


• Parts weighing under 5 kg (11 lbs.) with thin dividers must be determined to a strong help to counteract vibrations 


• Parts weighing under 2 kg (4.5 lbs.) must be coupled to a strong help utilizing coupling glue 


• Steel and cast steel, icy work device steel, treated steel and high temperature safe steel.


Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India.


Equostat 3 Hardness Tester

NDT-0018

Portrayal: 


It deals with the Rockwell Principle for stack estimation. It gives precise, fast, and reproduceable outcomes from estimation of infiltration profundity managed to characterized powers. It has extraordinary highlights as it does estimations autonomous of material, freedom of test's measurements and geometry. Measures from one side, no sponsorship fundamental. It has magnificent affectability, and is touchy for little entrance of a couple of µm.It is utilized generally in Engineering disciplines like oil, Mechanical and structural Engineering including research territories. 


Particular and FEATURES: 


It is appropriate for: 


• Scratch-touchy and cleaned surfaces 


• Thin parts, profiles and pipes with a divider thickness=2 mm 


• Hardness profile in warm influenced zone of welding creases

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India.

SCHMIDT Type N Test Hammer for Concrete

NDT-0019

Depiction: 


SCHMIDT compose Test Hammer is utilized for non-damaging testing of solid Measuring scope of this gadget for testing compressive quality of cement is 10 to 70 N/mm² (beneath 25 N/mm² type P is more qualified) and Impact vitality = 2,207 Nm. Bounce back qualities can be seen from a mechanical sliding scale. It is the main instrument to make utilization of bounce back guideline for solid testing. 


Particular and FEATURES: 


It has a spring-controlled mallet mass which slides on a plunger encased in a tubular lodging. Against the surface of the solid, the sledge is constrained by the spring and the separation of bounce back is estimated on a scale. The instrument must be adjusted in even, vertical or some other point at which the example is situated. This kind of mallet gave by Ray Export bolsters a reasonable, basic and fast technique for finding a sign of solid quality. Elements like smoothness of surface, shape and size of example, sort of bond and coarse total, dampness state of the solid, and degree of carbonation of surface. The Ray Export Schmidt Hammer, Type N with a N/mm^2 scale rather than psi. The entire pack incorporates a pounding stone, conveying case and a direction booklet with transformation graphs.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India.

SCHMIDT type NR Test Hammer for Concrete

NDT-0020

Depiction: 


Ray exports guarantees to offer high caliber, precise and solid analyzer. The gadget is utilized to quantify quality of different items. The gadget can gauge compressive quality of solid material from 10 to 70 N/mm² (beneath 25 N/mm² type P is more qualified) with Impact vitality of 2,207 Nm. Bounce back qualities can be seen from a scale. It tests in interims of 10 m each. 


Highlights: 


• Compressive quality estimation go 10 to 70 N/mm² 


• Impact vitality of 2,207 Nm 


• Tests in interims of 10 m each


Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab instruments supplier, engineering lab equipments exporter, civil engineering lab equipments supplier, engineering lab equipment manufacturers, engineering lab equipment manufacturer, engineering lab instruments manufacturerin Ambala, India.

Supply of NDT Metal-Testers from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }