science lab equipment manufacturer

Foam Testing Equipment

Foam Testing Equipment Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Foam Testing Equipment in India,

Quick answer. Before choosing between the two instruments here, decide which numbers your foam specification actually needs, because one hardness figure cannot describe a cushion. A usable specification needs density, indentation hardness at the percentage your standard names, and a support factor - the ratio of force at deep to shallow indentation - which FT-0001 gives only if it measures both levels in one run. FT-0002, the ball resilience tester, adds a quick rebound figure that suits incoming-goods checks. Density needs a cutting jig and a balance, which are not in this listing, so ask for them on the same quotation.

What this listing holds, and a code warning first

Two instruments for flexible foam: an indentation hardness tester, which measures the force needed to press a specified indentor into the foam, and a ball resilience tester, which drops a ball and measures how far it rebounds. They answer the two questions a mattress, cushion, seat or packaging buyer asks first - how firm is it, and how lively is it.

One fault in our catalogue data to know before ordering. The codes here are FT-0001 and FT-0002, and the footwear testing equipment listing uses the same prefix starting at the same number - so FT-0001 is an indentation hardness tester here and a sole adhesion tester there. Quote the code and the full product name together and ask for both to be confirmed on the proforma invoice. The product name is the reliable identifier until the codes are corrected.

Two Numbers, Not One

Foam is almost always specified badly, and the reason is that people ask for one number. A single hardness figure cannot describe a cushion, because two foams with identical hardness can feel completely different in use - one supports you, the other lets you sink to the base. A usable specification needs at least two numbers and preferably three.

NumberWhat it tells youHow it is obtained
DensityThe best single predictor of how long foam will last. Low-density foam of the right initial hardness still collapses firstA cut specimen of known dimensions and a balance. Not in this listing - ask us to quote a cutting jig and a balance with the instruments
Indentation hardnessHow firm it feels at normal sitting loadFT-0001, at the indentation percentage your specification names
Support factorWhether it keeps supporting as load increases, or bottoms out. It is the ratio of the force at deep indentation to the force at shallow indentationFT-0001 again, measured at two indentation levels in the same run - so confirm the instrument can do both and report the ratio

Ball resilience adds a fourth, quicker number that correlates with the springy feel of a foam and makes a good incoming-goods check because it takes seconds.

Indentation hardness: the specimen is half the measurement

This is the point on which most foam test results fall apart. Indentation hardness is not a property you can read off a dial independently of how you measured it. The figure depends on the indentor area, the specimen thickness and area, the percentage of thickness the foam is compressed by, and how long the load dwells before the reading is taken. Change any one and the number changes. So a foam described simply as being of a given hardness, with no indentation percentage and no specimen size, has not been specified at all.

Four questions follow, and they should be answered on the quotation rather than after delivery.

What indentor and what load range? Standards specify an indentor of defined area. Ask what is supplied, whether alternatives are available, and what load range the instrument covers, remembering that a range sized for seating foam may be too coarse for soft packaging foam.

What specimen size does it take, and is that the size your standard asks for? Specimen area and thickness are specified, and a specimen smaller than the standard allows will read harder, because the edges of the foam carry load they should not. Ask the maximum specimen size the platen accommodates.

How are the indentation levels and the dwell time set? Shallow and deep indentation points, with a defined rate and a defined dwell at each, are what make the result repeatable and what make a support factor calculable. Ask whether the instrument indexes to set percentages automatically and whether it records both forces.

Is pre-flexing required, and can the instrument do it? Flexible foam has a loading history: the first compression of a fresh specimen reads differently from the second, which is why standards normally require the specimen to be pre-flexed before measurement and tested within a stated time afterwards. If the instrument cannot pre-flex, the laboratory needs another way to do it consistently.

And as with every physical property of a cellular material, temperature and humidity matter. Foam is tested after conditioning in a standard atmosphere; a specimen brought in from a hot store and measured straight away will not agree with the same specimen measured tomorrow.

Ball resilience: quick, useful, easy to do wrong

The method is simple - a ball of specified mass is dropped from a specified height onto the foam and the rebound height is expressed as a percentage - and its simplicity is why it is good for routine checking. Three cautions.

The ball mass and the drop height are part of the method, so confirm both match your standard and that the instrument fixes them repeatably. The specimen must sit on a flat, rigid, level base: a thin specimen or a soft support measures the table as much as the foam. Ask what minimum specimen thickness the method requires. And rebound is read either by eye against a scale or by a sensor; eye readings scatter, so if the figure goes into a report, ask whether a measuring or sensing arrangement is available.

What foam testing this listing does not cover

Two instruments do not make a foam laboratory, and the gaps matter enough to name.

Durability. Compression set, constant-deflection or constant-load fatigue and repeated pounding tests are what tell you whether a cushion will still be a cushion in three years. None of them is in this listing, and for a furniture or mattress supplier they are the tests a customer is most likely to specify.

Tensile, tear and air flow. Tensile strength, elongation and tear resistance need a tensile machine with grips and a load cell suited to very low forces - see universal testing machines and tensile testing machines, and ask specifically about a low-range load cell, because a machine sized for metals cannot resolve the forces involved in tearing foam. Air flow or porosity, which governs comfort and breathability, needs its own instrument.

Fire performance, which may be a legal requirement. Foam used in furniture, bedding and transport interiors is subject to flammability regulation in many markets, and the applicable test is set by the destination country and the end use rather than by the material. That equipment is specialised and is not in this listing. If you are supplying furniture or vehicle interiors, establish which fire standard applies in your market before you buy any foam testing equipment at all, because it may be the only test that is not optional. Flammability, smoke and toxicity instruments for polymers are listed under plastic testing equipment; tell us the standard you need and we will advise whether those instruments cover it or whether a dedicated furniture fire rig is required.

What to ask for on the quotation

The standard and version each instrument implements; indentor area and alternatives; load range and resolution; maximum specimen size and the specimen size the standard requires; the indentation percentages the instrument can set, the rate, the dwell time and whether both forces are recorded so that support factor can be calculated; pre-flex capability; ball mass, drop height and how rebound is read; calibration certificate, traceability, the parameters certified and the recalibration interval; conditioning requirement and whether you need a conditioned area; bench space, mass and services at the position; nominal voltage, frequency and plug pattern; and the warranty and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you rely on it in a tender.

Related ranges: rubber testing equipment, which holds the hardness instruments for solid elastomers and an ageing oven, plastic testing equipment for polymer and film tests, fabric testing equipment for upholstery cover materials and footwear testing equipment for shoe components. The full set is listed under raw products testing. For a quotation, tell us the destination country, the standards your customers name, what the foam is used for and your expected sample throughput.

Frequently asked questions

Why is one hardness number not enough to specify foam?

Because two foams with identical hardness can feel completely different in use: one keeps supporting you, the other lets you sink to the base. A usable specification needs at least two numbers and preferably three. Density is the best single predictor of how long the foam will last, since low-density foam of the right initial hardness still collapses first. Indentation hardness tells you how firm it feels at normal sitting load. Support factor - force at deep indentation divided by force at shallow indentation - tells you whether it bottoms out. FT-0001 gives the last two, provided it records both forces.

Why do indentation hardness results from two laboratories disagree?

Because the figure depends on how it was measured. Indentor area, specimen thickness and area, the percentage of thickness compressed and the dwell time before the reading all change the number. A specimen smaller than the standard allows reads harder, because its edges carry load they should not. Fresh foam reads differently on its first compression, which is why specimens are normally pre-flexed and tested within a stated time. Temperature and humidity matter too: a specimen brought in from a hot store and measured straight away will not agree with the same specimen tomorrow. Fix all of these and results become comparable.

What should I check on the indentation hardness tester FT-0001 before ordering?

Four things, answered on the quotation rather than after delivery. The indentor supplied, whether alternatives are available, and the load range - a range sized for seating foam may be too coarse for soft packaging foam. The maximum specimen size the platen accommodates, against the size your standard requires. How the indentation levels and dwell time are set, whether it indexes to set percentages automatically and whether it records both forces so a support factor can be calculated. And whether it can pre-flex the specimen; if it cannot, your laboratory needs another consistent way to do it.

Is the ball resilience tester FT-0002 good enough for test reports?

It is quick and useful, and easy to do wrong. A ball of specified mass is dropped from a specified height and the rebound is expressed as a percentage, so confirm that the ball mass and drop height match your standard and that the instrument fixes them repeatably. The specimen must sit on a flat, rigid, level base, because a thin specimen or a soft support measures the table as much as the foam - ask the minimum thickness the method requires. Rebound read by eye against a scale scatters, so if the figure goes into a report, ask whether a measuring or sensing arrangement is available.

Which foam tests are not covered by this listing?

Durability tests - compression set, constant-deflection or constant-load fatigue and repeated pounding - are not here, and for a furniture or mattress supplier they are the tests a customer is most likely to specify. Tensile strength, elongation and tear resistance need a tensile machine with grips and a low-range load cell, because a machine sized for metals cannot resolve the forces involved in tearing foam; see universal testing machines and tensile testing machines. Air flow or porosity, which governs comfort and breathability, needs its own instrument. Fire performance equipment is specialised and also sits outside this listing.

Do I need fire testing before I buy foam testers?

If you supply furniture, bedding or transport interiors, establish that first. Foam in those uses is subject to flammability regulation in many markets, and the applicable test is set by the destination country and the end use rather than by the material - so it may be the only test that is not optional. Flammability, smoke and toxicity instruments for polymers are listed under plastic testing equipment. Tell us the standard you need and we will advise whether those instruments cover it or whether a dedicated furniture fire rig is required.

Key takeaways

  • Specify at least two numbers - density plus indentation hardness, and preferably a support factor as well.
  • Support factor needs two indentation levels in one run - confirm FT-0001 records both forces.
  • The specimen is half the measurement - indentor area, specimen size, indentation percentage and dwell all change the result.
  • Pre-flex and condition every specimen, or results will not repeat from one day to the next.
  • Quote the code and the full product name together - the footwear testing listing reuses FT-0001 for a different instrument.
  • Settle the fire requirement first for furniture, bedding and transport interiors - it is set by destination country and end use.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Specifications - indentor area, load range and resolution, specimen size, indentation percentages, rate and dwell, ball mass and drop height - are confirmed in writing on the quotation. For calibration records, standards or approvals, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing defect: the codes here, FT-0001 and FT-0002, use the same prefix and numbering as the footwear testing equipment listing, where FT-0001 is a sole adhesion tester, so quote the full product name with the code and ask for both to be confirmed on the proforma invoice until the codes are corrected. Density measurement needs a cutting jig and balance that are not listed here.

Indentation Hardness Tester

FT-0001

Space Hardness Tester for rubber treated coir padding is utilized for the space hardness estimation of froth, PU froth, rubber treated coir and latex froth. The framework comprises of a shear shaft write stack cell over which the test example is kept. The test example is squeezed with an indentor of the predetermined measurement mounted on self/adjusting metal roller to such an extent that it can alter its tendency to coordinate the best face of the test example. The indentor can be moved down physically through a hand wheel (and in addition by engine and rigging box) and screw course of action, thickness is estimated on strip scale and Compression is estimated on an advanced marker and the relating load is estimated on the computerized readout of the heap cell.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India. 

Ball Resilience Tester

FT-0002

Space Acerbity Tester for elastic advised coir added is activated for the amplitude acerbity admiration of froth, PU froth, elastic advised coir and acrylic froth. The framework comprises of a microburst shaft address assemblage corpuscle over which the analysis archetype is kept. The analysis archetype is awkward with an indentor of the agreed altitude army on self/adjusting metal roller to such an admeasurement that it can adapt its addiction to alike the best face of the analysis example. The indentor can be confused bottomward physically through a duke caster (and in accession by agent and accouterment box) and spiral advance of action, array is estimated on band calibration and Compression is estimated on an avant-garde brand and the apropos amount is estimated on the computerized readout of the abundance cell.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipmentsin Ambala, India. 


Supply of Foam Testing Equipment from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }