Quick answer. Equip a footwear laboratory against your complaints file, not the catalogue. Write down the failures customers actually return shoes for and buy the instrument that predicts each one: soles coming away point to the sole adhesion tester (FT-0001), cracking across the front to the belt and Bennewart flex testers (FT-0003, FT-0004), and safety-toe requirements to the toe cap impact tester (FT-0002). Worn uppers and rubbed-off colour are abrasion and rub fastness, which are not in this listing. And quote each code with its full product name, because the foam testing listing reuses the same FT codes for different instruments.
Four instruments: a sole adhesion tester, a toe cap impact tester, a belt flex tester and a Bennewart flex tester. Between them they address the two failures that generate most footwear complaints - the sole coming away from the upper, and cracking where the shoe flexes - plus the impact protection test that safety footwear has to pass.
Before you order, note a fault in our catalogue data that could cost you the wrong delivery. The codes in this listing run FT-0001 to FT-0004. The foam testing equipment listing uses the same prefix and starts again at FT-0001, so FT-0001 is a sole adhesion tester here and an indentation hardness tester there, and FT-0002 is a toe cap impact tester here and a ball resilience tester there. Quote the code and the full product name together, and ask for both to be confirmed on the proforma invoice before anything ships. We are having the codes corrected; in the meantime the product name is the reliable identifier.
A footwear laboratory can be equipped from a catalogue or from a complaints file, and the second works better. Write down the three failures your customers actually return shoes for, then buy the instrument that predicts each one. In practice the list is short and the mapping is direct.
| The complaint | The test that predicts it | What to settle |
|---|---|---|
| "The sole came off" | Sole adhesion, FT-0001 | Peel or tensile bond; how specimens are cut and gripped; whether the bond is tested after conditioning or ageing rather than fresh |
| "It cracked across the front" | Flex testing, FT-0003 and FT-0004 | Which method, how many flexes, at what temperature, and how cracking is assessed |
| "The safety toe failed" or a certification requirement | Toe cap impact, FT-0002 | Impact energy, drop arrangement, how internal clearance is measured, and which standard you certify to |
| "The upper wore through" or "the colour rubbed off" | Abrasion and rub fastness - not in this listing | See the leather testing equipment range for abrasion, crockmeter and finish adhesion |
Sole bond failure is the most expensive routine failure in footwear, because it happens after sale and there is no argument about whose fault it is. The instrument measures the force needed to separate sole from upper, and three things decide whether your number means anything.
How the specimen is prepared. A whole shoe has to be cut into a strip of defined width through the bond line, and the cut itself can damage the bond. Ask what specimen width the method requires, what cutting arrangement is recommended and whether a sample holder is supplied for whole-shoe testing.
How it is gripped and pulled. Peel at a defined angle and rate, or straight tension, and the two give different numbers. Ask the grip design, the rate of separation and whether the rate is adjustable to match your standard.
When it is tested. This is the one most often got wrong. Adhesive bonds change in the days after they are made, and they change again in heat and humidity, so a bond tested an hour after pressing can read quite differently from the same bond tested after conditioning or after accelerated ageing. Ask what the standard specifies and build that waiting time into the laboratory schedule - a figure taken too early flatters production and tells you nothing about the shoe in a customer's cupboard.
FT-0002 is a safety test, not a quality test, and that changes how it should be treated. A safety footwear marking is a claim about protection, and in most markets it is a regulated claim: if the product carries it, the product has to meet the standard behind it. So the instrument has to implement the standard exactly, and the result has to be recorded against identified production samples rather than prototypes.
Ask, specifically: what impact energy the rig delivers and over what range - the highest protection class in the common international standard is commonly specified at two hundred joules, so confirm the figure against the standard you certify to; how the energy is set, by mass and drop height, and how both are verified; how the clearance remaining under the toecap after impact is measured, since the method normally uses a shaped modelling-clay cylinder whose dimensions and consistency are themselves specified; and whether a compression test facility is included, because toe protection standards usually require compression as well as impact.
Two practical points. The test is destructive, so build the cost of sacrificed shoes into the testing budget. And a drop-weight rig is a mechanical hazard: ask about the guard, the release and retention mechanism, how the weight is prevented from double-striking, and whether the frame is to be bolted down. If a certification body audits your file, they will look at the calibration of this rig before almost anything else, so ask what is certified - energy, mass, drop height, the clay - by whom, and at what interval.
Flex cracking is the second big complaint, and it is a material and construction failure rather than an assembly one. Both instruments flex specimens repeatedly until cracking appears; they differ in geometry and in which method they implement, and that is the first question to ask, because flex results from different methods are not comparable.
For both, settle: the number of flexes the specification requires and whether the counter stops automatically at that figure; how many specimens run at once, which sets throughput; how the specimen is mounted and whether the mounting itself initiates a crack; whether the instrument can be run at low temperature, since a cold flex requirement is common for uppers and coated materials and a finish that passes at room temperature can fail at minus ten; and how cracking is assessed afterwards - at what magnification, against what rating scale, and by how many assessors. Related instruments for the materials themselves are listed under leather testing equipment and coated fabric testing equipment; soling compounds are covered in rubber testing equipment, which also holds the hardness instruments a soling specification will name.
Four instruments cannot equip a complete footwear laboratory, and it is better to say so. Not in this listing: whole-shoe flexing and walking simulation; slip resistance, which is a major regulated property for safety and occupational footwear; heel attachment and heel fatigue; shank stiffness; insole and lining abrasion; water penetration of the whole shoe; and sizing and last measurement. Tell us which of those your customers specify and we will quote against the specification rather than against this page. Materials testing for the components - leather, textile, coated fabric, rubber, foam - is spread across the other listings in the raw products testing group, and tensile and tear strength on components is done on the machines in universal testing machines.
The standard and version each instrument implements, named explicitly; specimen size, preparation and mounting arrangement; rate of separation or flexing and whether it is adjustable; for the impact rig, energy range, how mass and drop height are set and verified, the clay or indicator arrangement, guarding and whether compression testing is included; temperature capability on the flex testers; number of specimens per run; calibration certificate, traceability, what parameters are certified and the recalibration interval; consumables with prices - cutting dies, clay, grip faces, specimen clamps; services at the position; nominal voltage, frequency and plug pattern; and the warranty, commissioning and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you rely on it for a product claim.
For a quotation, tell us the destination country, the standards your customers or your certification body name, whether safety footwear is in scope, and your expected sample throughput. And when you enquire about anything in this listing, give the product name as well as the FT code.
Because of a fault in the catalogue data. The codes in this listing run FT-0001 to FT-0004, but the foam testing equipment listing uses the same prefix and starts again at FT-0001. So FT-0001 is a sole adhesion tester here and an indentation hardness tester there, and FT-0002 is a toe cap impact tester here and a ball resilience tester there. Quote the code and the full product name together, and ask for both to be confirmed on the proforma invoice before anything ships. Until the codes are corrected, the product name is the reliable identifier.
The sole adhesion tester measures the force needed to separate sole from upper, and three things decide whether the number is useful. Specimen preparation: a whole shoe is cut into a strip of defined width through the bond line, and the cut itself can damage the bond, so ask the specimen width, the recommended cutting arrangement and whether a sample holder is supplied. Gripping and pulling: peel at a defined angle and rate, or straight tension, give different numbers, so ask the grip design and whether the separation rate is adjustable. Timing is the third.
When your standard says, which is the point most often got wrong. Adhesive bonds change in the days after they are made and change again in heat and humidity, so a bond tested an hour after pressing can read quite differently from the same bond tested after conditioning or accelerated ageing. Ask what the standard specifies and build that waiting time into the laboratory schedule. A figure taken too early flatters production and tells you nothing about the shoe in a customer's cupboard, which is where a sole bond failure becomes expensive.
Treat it as a safety test, not a quality test. A safety footwear marking is a regulated claim in most markets, so the instrument has to implement the standard exactly and results have to be recorded against identified production samples. Ask what impact energy the rig delivers and over what range, and confirm it against the standard you certify to; how energy is set by mass and drop height and how both are verified; how clearance under the toecap is measured, normally with a specified modelling-clay cylinder; and whether compression testing is included.
The test is destructive, so build the cost of sacrificed shoes into the testing budget. A drop-weight rig is also a mechanical hazard: ask about the guard, the release and retention mechanism, how the weight is prevented from double-striking, and whether the frame is to be bolted down. If a certification body audits your file, the calibration of this rig is one of the first things it checks, so ask which parameters are calibrated - energy, mass, drop height, the clay - by whom and how often, and contact us for the latest copies of the relevant certificates.
Start with the method your specification names, because the two instruments differ in geometry and method, and flex results from different methods are not comparable. Then settle the number of flexes required and whether the counter stops automatically; how many specimens run at once, which sets throughput; whether the mounting itself starts a crack; whether the instrument runs at low temperature, since a finish that passes at room temperature can fail in the cold; and how cracking is assessed - at what magnification, against what rating scale and by how many assessors.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Specifications, including impact energy, separation rate and flex count, are confirmed in writing on the quotation; for calibration and other certificates, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing notes: the FT code prefix is shared with the foam testing equipment listing, which restarts at FT-0001, so FT-0001 and FT-0002 each identify two different instruments; until the codes are corrected, the product name is the reliable identifier.
Bottom Adhesion Tester is utilized for the underside bond of the footwear. Advanced model is likewise accessible. The framework comprises of a spring dynamometer to demonstrate the heap connected at the intersection of the sole and the upper, a lever plan to transmit the heap applied on the toe piece to the spring dynamometer, a straight edge support for laying the shoe on amid the test, and an arrangement of exchangeable toe pieces having diverse ebb and flow. The spring dynamometer demonstrates the heap connected on the joint specifically in kilograms, considering the mechanical favorable position of the lever transmitting the power from the toe piece to it. The heap is demonstrated on a round dial. The dynamometer has two pointer, a dark consider to demonstrate the immediate load following up on the toe piece and a red sham pointer to show the most extreme load connected before disappointment of grip. The toe piece are five in number and having diverse ebb and flow to empower toes and foot sole areas of various shapes and sizes to be tried. The length of curve of each toe piece, in any case, is the same to guarantee that the heap is connected just on a settled length of joint. They are produced using carbon steel for giving a long operational life. Any of the toe pieces can be held in the gear at one time. The support on which the shoe is put amid the test has movable stature to empower soles of various thickness to be tried. The stature of the support is balanced with the assistance of spacer strips furnished with the instrument. The instrument is done in painting and brilliant chrome plating to give it a consumption safe wrap up.
Specialized SPECIFICATIONS:
· Method of Test for Footwear Part I: Dimensions, Fitting, Adhesion Test, Peel Test, Heat Resistance Test, and Aging Test.
· Specification for Leather Safety Footwear having direct shaped underside.
Toe Cap Impact Tester is made on a flat stage which has two guide bars which control the effect weight. There is a mellow steel plunger of determined measurements which is utilized the middle of the road parts between the effect weight and the toe top. The plunger is uninhibitedly upheld to the toe top. The base of the machine is set on the hard wood of determined measurements. A case for estimating the freedom at the season of most extreme misery is additionally provided with the instrument. Every one of the parts are either painted or chrome platted to give the instrument an erosion free long life
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipment, engineering equipments exporters, engineering equipments suppliers, engineering equipments supplier, engineering educational equipments, engineering equipments manufacturers in Ambala, India.
Out bottoms of footwear or other flexing segments may endure splitting being used because of flexing. Splits as a rule create at purposes of high surface strain coming about because of the outline of the sole example, without there being any slices to starts them. The Belt Flex Tester is intended to flex finish soles with their examples flawless in a way like those experienced in genuine utilize. Tests completed utilizing it give a manual for the danger of such splits creating amid utilize.
The test examples are connected to the outside of a nonstop belt, which is driven cycle two rollers. The huge roller drives the belt while development of the littler roller is made the flexing to some degree more serious than is real utilize. This type of flexing likewise nearly mimics the real bowing at each progression as it delivers a brief time of fast flexing took after by a more drawn out period when the example isn't being flexed.
An ordinary test comprises of various flexing keeps running up to an aggregate of 50,000 flexes, with an examination for splitting toward the finish of each run.
The Belt Flex Tester comprises of two roller on which a level belt moves. The bigger roller which is the driving roller turns at a predefined speed to give the predetermined recurrence of flexing with the assistance of an electric engine and V belt game plan. The second roller, which is the flexing roller, pivots with the development of the belt.
The flexing rollers are somewhat barrel formed in order to limit sideways development of the belt. A hand wheel is appended to the front end of these rollers to empower the belt to be moved by hand. The gear is provided with three flexing rollers, one for typical soles, the second for exceptionally adaptable soles, and the third for extremely unbending soles.
The separation between the driving and the flexing rollers can balanced with the assistance of a screw plan to empower the belt to be mounted over various flexing rollers and to take into account little contrasts in belt length. This is finished by turning a hand wheel in favor of the analyzer.
The analyzer is fitted with an acrylic title page and a wire work security monitor, which permits sufficient dissemination of cooling air round the test examples amid the test. For wellbeing of the client, the engine can be begun just when cover is shut.
Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India.
Bennewart flex testing is planned should determine the safety of a part from material with curtailed Growth Throughout repeater flexing. It could Additionally make used to assess the impact from claiming surface designs looking into split start Also development.
This test will be particularly pertinent of the outsoles for footwear, Anyhow might additionally make utilized for specific other adaptable parts.
Those Bennewart flex analyzer comprises of a drive unit including about a electric engine for pulleys What's more belts What's more join component on provide for a swaying development to a standout amongst the two grips holding those two finishes from claiming test specimen, the opposite grip being settled.
Those swaying grip need weapon metal bushes, which slides once two solidified Furthermore ground bearing steel rods to provide for it An in length working an aggregation. Every grip comprises about swayable bases pivoted once ball bearings Along these lines that those two finishes of the test example need aid nothing will adjust themselves with the regular shape of the example Throughout flexing.
Those hub something like which those grip bases sway an aggregation. In the plane about their example holding face. A six digit pre-set electronic advanced counter the numbers for test cycles What's more likewise stops those engine after pre-set numbers of test cycles.
Those mechanical assembly may be completed On gray hammer tone arm staving, painting Also brilliant chrome/ zinc plating will provide for it a erosion safe complete.
A cutting bite the dust for preparation from claiming test example starting with sheet What's more slitting punch for dance for settling on beginning split would accessible as nonobligatory adornments.