science lab equipment manufacturer

Rubber Testing Equipment

Rubber Testing Equipment Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Rubber Testing Equipment in India,

Quick answer. Settle the hardness scale your specification names before comparing the eight hardness instruments. Shore A suits soft and medium elastomers, Shore D hard rubber, and IRHD is used where specifications call for it, and readings do not convert reliably between them. Then decide stand and dwell: a stand applies a defined force square to the surface, and a timed reading controls the creep that makes rubber hardness fall second by second. For seals and gaskets, though, compression set, recovery and tension set predict service life far better than hardness, and they depend on the multi-cell ageing oven RTE-0025.

What this range covers

Twenty-five instruments, coded RTE-0001 to RTE-0025, for a rubber and elastomer laboratory. Eight of them measure hardness, which tells you something about how rubber is specified. The rest cover compression - compression set, compressibility and recovery and three compression testing machines; permanent deformation in tension; density by specific gravity; DIN abrasion; flexing and fatigue with De-Mattia and Ross flex testers; impact resilience; split tear; rub proofness; gas permeability; a specimen cutting press; and a multi-cell ageing oven.

Eight hardness instruments is not redundancy. Rubber hardness is measured on several scales with several instrument types, the scales are not interchangeable, and a specification names one of them. The section below is the part of this page worth reading before you compare prices, because getting it wrong produces numbers that look perfectly reasonable and that your customer cannot use.

Scale, Stand, Dwell

Three things make a rubber hardness reading reproducible. Miss any one and two laboratories testing the same compound will disagree.

What to settleWhy
ScaleShore A, Shore D or IRHD - whichever your specification namesShore A suits soft and medium elastomers, Shore D hard rubber and rigid plastics, and IRHD is used where specifications call for it and in a micro form for thin or small specimens. Conversion between the scales is approximate at best; a number on the wrong scale is not convertible into a compliant result
StandHand-held or stand-mounted with a defined massA hand-held durometer is pressed by a person, so the applied force and the squareness of contact vary with the operator. A stand applies a defined force perpendicular to the surface, and that is what turns a reading into a measurement. If results go on a certificate, buy the stand
DwellThe time between contact and reading, as the standard specifies itRubber creeps under the indenter, so the indicated hardness falls as the seconds pass. Standards specify a dwell - one second, three seconds, fifteen seconds depending on the method - and a hardness value quoted without its dwell time is incomplete. This is what the dual-needle and timed digital instruments exist to control

Two further points that decide whether a hardness number is valid at all. Specimen thickness: the methods specify a minimum, and a specimen thinner than the minimum reads harder because the indenter feels the bench through it; stacking thin pieces is permitted only where the method says so, and on moulded products it usually is not. Position: readings must be taken a stated distance from any edge and from each other, and the median of several readings is reported rather than one. Ask us which standard each of the eight instruments implements, whether a stand and a timer are included, and what reference rubber blocks are supplied for checking - a durometer is checked against reference blocks, and a laboratory without them has no way of knowing its instrument has drifted.

The tests that predict whether a seal keeps sealing

For anyone making gaskets, O-rings, bushes or mountings, the instruments that matter most are not the hardness ones. They are compression set, compressibility and recovery, and tension set, and they all measure the same underlying thing: how much deformation is permanent after the rubber has been held deformed, hot, for a long time.

That is the property behind almost every leak in service. A compound that recovers fully at twenty-five degrees may take a permanent set at a hundred, and a seal that has taken a set no longer presses on the flange. Ask about: the jigs and spacers, and whether the compression is to a fixed deflection or a fixed load, because the two methods are different and give different numbers; the parallelism and flatness of the platens, since a non-parallel jig loads the specimen unevenly; the temperature and time the method specifies and how you will hold them, which usually means the ageing oven; and the recovery period and temperature before measurement, which is part of the method and not a convenience.

The multi-cell ageing oven, RTE-0025, is worth more attention than its position at the end of the listing suggests. It is not an ordinary laboratory oven, and the reason is specific: antidegradants, plasticisers and other volatiles migrate out of one compound and into another when samples share an air space, which changes the ageing behaviour of both. The standards therefore require that different compounds are aged in separate cells with their own air flow. A single-chamber oven full of mixed compounds produces ageing results that are a property of the batch of samples rather than of any one compound. Ask how many cells there are, whether each has its own air change and at what rate, the temperature range and uniformity, and how temperature is recorded, because an ageing test unrecorded for seventy-two hours is an act of faith.

Abrasion, flexing and tearing: where specimen preparation decides the answer

The DIN abrasion tester reports volume loss when a specimen is run against an abrasive sheet under load. The subtlety is the sheet: abrasive sheets vary from batch to batch, so the method requires the sheet to be checked against a reference compound and the result expressed relative to it. Ask what reference rubber is supplied, where it is obtained, and what sheets cost - as everywhere in materials testing, the consumable is the running cost and in this case it is also the calibration.

The De-Mattia and Ross flex testers find cracking under repeated bending, which is how rubber fails in service far more often than by breaking. Ask the number of specimens per run, the stroke and frequency, whether a cold chamber is available, and how cracks are assessed and graded. Note that a De-Mattia tester also appears in the fabric testing equipment listing, spelled slightly differently; they are the same kind of instrument applied to different materials, so quote by code and full name.

The split tear tester and the specimen cutting press belong together, because tear results are more sensitive to specimen preparation than any other rubber test. A die that is blunt, or a cut edge with a small nick in it, starts a tear early and scatters the results - and the scatter looks like material variation rather than preparation. Budget for dies, for resharpening and for the discipline of replacing them. Ask which dies each test needs, whether the press takes them all, and what resharpening costs locally. Tensile and tear strength themselves are measured on a machine from the tensile testing machines or universal testing machines range, and for rubber you want a low-capacity load cell and grips that do not cut the specimen.

The quiet workhorses: specific gravity and gas permeability

Two specific gravity instruments are listed, and density is the most undervalued routine test in a rubber laboratory. It is quick, it needs no consumables beyond water, and a change in density between batches is the earliest warning that the filler loading has changed - which usually means the compound has changed without anyone saying so. For a goods-inwards check on bought-in compound it is the first test to run. Ask about the balance resolution, the hydrostatic arrangement and whether temperature correction is applied.

Gas permeability matters if your products hold gas - bladders, diaphragms, inflatable seals, pneumatic components. Ask which gas the test uses, what pressure difference is applied, the specimen area and thickness required, how long a determination takes and what gas supply is needed at the position. Ask also what the instrument reports, since permeability, transmission rate and diffusion coefficient are related but not the same quantity, and a specification names one.

Two things to know about this listing before you order

The names in this listing overlap more than they should. Eight records are hardness testers, including one whose name ends in a digit because it duplicates another; three are compression testing machines; and two are specific gravity instruments - and the listing does not say what separates them. One record spells a standards body as an ordinary word rather than an acronym. So: ask for the specification sheets of the records you are choosing between, side by side, and compare on scale, stand, dwell control and whether reference blocks are included. And as always on this part of the catalogue, quote the code and the full product name together and have both confirmed on the proforma invoice. If a name looks like a duplicate, ask; it is more likely to be our catalogue data than a second product.

What to ask for on the quotation

For each hardness instrument: scale, standard implemented, whether a test stand and timer are included, dwell control, reference blocks supplied, and calibration certificate. For the set and recovery tests: jigs, spacers, fixed-deflection or fixed-load method, platen flatness, and the oven they depend on. For the ageing oven: number of cells, air change per cell, temperature range, uniformity and recording. For abrasion: reference compound supplied, sheet source and cost. For the flex testers: specimens per run, stroke, frequency, cold capability and assessment method. For cutting: dies included, resharpening arrangement. For all: calibration and traceability, bench space and mass, services at the position, nominal voltage, frequency and plug pattern, consumables and spares with prices and lead times, and the warranty and local service position. For any certification stated here, contact us for the latest copies of the relevant certificates before you rely on it in a tender or an accreditation file.

Related ranges: foam testing equipment for cellular materials, plastic testing equipment for thermoplastics and films, footwear testing equipment for soling and shoe components, and coated fabric testing equipment for rubber-proofed cloth. The full set is listed under raw products testing. For a quotation, tell us the destination country, the standards your customers name, which hardness scale your specifications use and what you make - a gasket plant, a tyre retreader and a footwear soling unit need three different subsets of this page.

Frequently asked questions

Which hardness tester do we need: Shore A, Shore D or IRHD?

The one your specification names. Shore A suits soft and medium elastomers, Shore D hard rubber and rigid plastics, and IRHD is used where specifications call for it, including a micro form for thin or small specimens. Conversion between scales is approximate at best, so a number on the wrong scale cannot be turned into a compliant result. Then choose hand-held or stand-mounted: a hand-held durometer varies with the operator's force and squareness, while a stand applies a defined force perpendicular to the surface. If results are reported to customers, buy the stand, and ask what reference rubber blocks come for checking drift.

Why do two hardness readings on the same rubber disagree?

Usually dwell, thickness or position. Rubber creeps under the indenter, so the indicated hardness falls as seconds pass; methods specify a dwell of one, three or fifteen seconds, and a value quoted without its dwell is incomplete, which is what dual-needle and timed digital instruments control. A specimen thinner than the method's minimum reads harder because the indenter feels the bench through it, and stacking thin pieces is allowed only where the method says so, rarely on moulded products. Readings must also be a stated distance from edges and from each other, with the median of several reported rather than a single reading.

Which tests predict whether a seal will keep sealing?

Compression set, compressibility and recovery, and tension set. They all measure how much deformation stays permanent after rubber has been held deformed, hot, for a long time, which is the property behind almost every leak in service. A compound that recovers fully at 25 deg C may take a permanent set at 100 deg C, and a seal that has taken a set no longer presses on the flange. Ask about the jigs and spacers, whether compression is to a fixed deflection or a fixed load, since the two give different numbers, the flatness and parallelism of the platens, and the recovery period before measurement.

Why does the ageing oven RTE-0025 have separate cells?

Because compounds contaminate each other. Antidegradants, plasticisers and other volatiles migrate out of one compound and into another when samples share an air space, changing the ageing behaviour of both. The methods therefore require different compounds to be aged in separate cells with their own air flow, and a single-chamber oven full of mixed compounds produces results that belong to the batch of samples rather than to any one compound. Ask how many cells there are, whether each has its own air change and at what rate, the temperature range and uniformity, and how temperature is recorded across a long test.

What drives the results on the abrasion, flex and tear testers?

Consumables and specimen preparation. The abrasion tester reports volume loss against an abrasive sheet, and sheets vary from batch to batch, so results are expressed relative to a reference compound; ask what reference rubber is supplied and where sheets come from, since the consumable is also the calibration. For the De-Mattia and Ross flex testers, ask the specimens per run, stroke, frequency, cold capability and how cracks are graded. Tear results are the most sensitive to preparation: a blunt die or a nicked edge starts a tear early, so ask which dies the cutting press takes and how resharpening is handled.

Why are specific gravity and gas permeability worth having?

Specific gravity is the most undervalued routine test in a rubber laboratory. It is quick, needs nothing beyond water, and a density change between batches is the earliest warning that the filler loading, and so the compound, has changed; it is the first goods-inwards check on bought-in compound. Ask the balance resolution, the hydrostatic arrangement and whether temperature correction is applied. Gas permeability matters if your products hold gas, such as bladders, diaphragms and inflatable seals. Ask which gas and pressure difference are used, the specimen size, the test time, and whether it reports permeability, transmission rate or diffusion coefficient.

Key takeaways

  • Scale first: Shore A, Shore D and IRHD are not interchangeable, so buy the scale your specification names.
  • Stand and dwell make it a measurement: a defined force and a timed reading take the operator out of the result.
  • Check thickness and position: thin specimens read hard, and the median of several well-spaced readings is reported.
  • Set predicts leaks: compression set, recovery and tension set matter more than hardness for seals and gaskets.
  • Separate cells for ageing: RTE-0025 stops compounds contaminating each other's ageing results.
  • Density is the early warning: a batch-to-batch density change flags a filler change before anyone mentions it.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Specifications for RTE-0001 to RTE-0025, including hardness scale and dwell control, test stand and reference blocks, jig and platen details, ageing oven cells and air change, and the dies supplied, are confirmed in writing on the quotation. For calibration or traceability documents, contact us for the latest copies of the relevant certificates. No price is quoted on this page. Listing note: the eight hardness records include one whose name ends in a digit because it duplicates another; three compression testing machines and two specific gravity instruments are listed with nothing to separate them; one record spells a standards body as an ordinary word; and a De-Mattia tester also appears in the fabric testing listing under a slightly different spelling.

Compression Testing Machine (Hand Operated)

RTE-0011

Pressure Testing Machine hand worked fitted with dial check. The water driven jack is settled to base. The upper platen has a self-adjusting activity and is connected to a screw which goes through the cross head and can be raised for brought down for introductory leeway change. The lower platen lays on the jack slam and is situated with the assistance of a centring pin. Stacking is expert by the upward development of the lower platen.

 

Technical Details:

Specification

Model/Capacity

Capacity

50, 100, 120, 200, 300 (KN)

Ram Travel (MM)

50

Pressure Gauge Diameter (MM)

200

Pressure Gauge (In Kn)

500, 1000, 1200, 2000, 3000 (KN)

Least count (In kn)

2KN, 5KN, 10KN, 15KN

Maximum Pressure (Kgs./cm)

480

Platen Diameter (MM)

300

Horizontal Clearance (MM)

330

Height of Load Frame (MM)

1300

Cube (MM)

100, 150, 200

Supply Voltage

Cylindrical

 

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India.


Digital Compression Testing Machine

RTE-0012

Pressure testing machine 2000 kn (200 tons) limit electrically worked fitted with computerized show. The water powered jack of 200 tone limit is settled to base.The upper platen has a self adjusting activity and is appended to a screw which goes through the cross head and can be raised for brought down for beginning freedom alteration. The lower platen lays on the jack smash and is situated with the assistance of a focusing pin. Stacking is refined by the upward development of the lower platen. The machine is reasonable for activity on 440v, 3-stage, air conditioning supply.

 Technical Details:

Specification

Model/Capacity

Capacity

50, 100, 120, 200, 300 (KN)

Ram Travel (MM)

50

Pressure Gauge Diameter (MM)

200

Pressure Gauge (In Kn)

500, 1000, 1200, 2000, 3000 (KN)

Least count (In kn)

0.1KN

Maximum Pressure (Kgs./cm)

480

Platen Diameter (MM)

300

Horizontal Clearance (MM)

330

Height of Load Frame (MM)

1300

Cube (MM)

100, 150, 200

Cylinderical

100 X200, 150 X 300

Motor  Voltage

440 V. 3ph, 50 HZ

R.P.M

950

Contactor

3 Phase

 

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India.

Specific Gravity Tester

RTE-0013

Particular Gravity Tester scope of 0.9 to 3.0, the lower stick likewise goes about as a sinker. Likewise, the container is put on the base of an edge which can be climbed or down on a pole settled to the base plate. An example of any shape can be utilized for assurance of particular gravity. Its weight should, anyway lie in the vicinity of 5 and 12 g for adjust. The example utilized might not be solvent in water or be affected by it in any capacity. On the off chance that the example has a cell structure, the cells should be of shut sort with the goal that the retention of water is kept at least.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India. 


Compression Set

RTE-0014

Comprises of four treated steel plates as above fitted in an apparatus having an unbending base plate and are guided on a couple of vertical poles. The spacers are additionally guided on similar bars and are furnished with springs to expand space between the plates for embeddings the examples. The examples are packed with the assistance of a screw turned by a handwheel. The entire course of action empowers fast utilization of pressure stack on the specimen.compact size can be set inside a stove for leading tests at hoisted temperature.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India. 


Shore A Hardness Tester

RTE-0015

Shore A Hardness Tester - Hardness is a standout amongst the most vital properties that decide the reasonableness of any elastic part for its proposed end utilize. Uncalled for hardness may invalidate the fundamental point for which the part is composed. In this manner, exact and solid assurance of hardness is of extraordinary significance in elastic industry. and The spring write hardness analyzer, additionally called as Shore hardness analyzer or Durometer, is the most ordinarily utilized instrument for estimation of hardness of any elastic segment. It depends on the estimation of profundity of space of an indentor of determined shape when constrained into the material under a predefined weight. and This test strategy is an observational technique proposed essentially for control purposes. No straightforward relationship exists between hardness dictated by this test technique and any central property of the material being tried. common lab types of gear makers and.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India. 


Impact Resilience Tester

RTE-0016

Effect Resilience Tester - Resilience or the capacity to assimilate stuns or affect powers and to hose their impact is one of the significant properties of rubbers. One of the techniques utilized for the assurance of effect flexibility of strong rubbers depends on the estimation of the stature of bounce back of a standard plunger after it is dropped from a settled tallness onto the surface of the elastic example under test. This test is directed on a Vertical Rebound Resilience Tester. and The Impact Resilience Tester (vertical bounce back sort) comprises of a plunger which can be dropped from a settled tallness onto the best face of the test example, a vertical plunger manage over which the plunger moves amid its fall and ensuing bounce back, a course of action to hold the plunger at the predetermined stature and to discharge it from that point, and a scale set apart in 100 similarly divided divisions to give straightforwardly the bounce back tallness as a level of the dropping tallness. common lab types of gear producers.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the bestengineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India. 


Specimen Cutting Press

RTE-0017

Example Cutting Press - For leading tests on different materials or items, test examples of determined shapes and size are to be removed of the test tests. Test examples of elastic, calfskins, textures, froth, adaptable/semi-inflexible plastics and comparable different materials are normally cut with the assistance of blade edged kicks the bucket of fitting shapes and measurements. The test/chunk is put over a level and smooth bit of plywood, hardwood, unbending plastic, or hard elastic (ebonite) while the chopping kick the bucket is pushed down from the best to remove the test examples. common lab types of gear makers.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India.

IRHD Hardness Tester

RTE-0018

IRHD Hardness Tester - Hardness is a standout amongst the most vital properties, which decide the reasonableness of any elastic part for its planned end utilize. Inaccurate hardness may invalidate the fundamental point for which the segment is outlined. Consequently exact and dependable assurance of hardness is of extraordinary significance in elastic field. Among the different means for the assurance of elastic hardness the most imperative ones are the Durometer and the IRHD Hardness Tester. While the primary uses the rule of space of a truncated cone in elastic under shifting burdens acting through a spring, the second technique utilizes a settled dead load following up on a hemispherical indenting tip. While the primary strategy experiences the disservice of perpetual set getting created in the spring and therefore influencing its precision, the second technique, being founded on dead load rule, is free from this issue. and The& IRHD Hardness Tester is table model gear appropriate for reference testing of hardness of elastic or comparative polymers in the research facility. It comprises of a plunger bar conveying a solidified hemispherical tip of the predefined width at its lower end. The pole is situated inside a tube shaped guide and is obliged to move inside it. The base of the guide goes about as the weight foot encompassing the purpose of space. Under typical condition the weight foot reaches out beneath the indenting tip, along these lines keeping it from getting harmed. An indenting load is situated over the plunger pole without straightforwardly following up on it common lab types of gear producers. Elastic Testing Lab hardware manufacturers, exporters and Rubber Testing Lab providers

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India. 

Gas Permeability Tester

RTE-0019

Gas Permeability Tester - Permeability of elastic sheets to gases is characterized as the rate of volume stream of gas under consistent state conditions between inverse appearances of a unit 3D square of strong elastic, when subjected to unit weight distinction under a controlled temperature. The estimation of this trademark is of essential in the assessment of mixes for items, for example, inward tubes, tubeless tire liners, hoses, inflatables or different gas holders, seals and stomachs and so on. The& Gas Permeability Tester for elastic comprises of a test cell with course of action for keeping up a steady hoisted temperature and an even glass hairlike framework for estimating the volume of gas penetrated. The test cell comprises of metal squares having autonomous courses of action for warming with the assistance of cartridge compose radiators. The temperature of each ck is shown and controlled independently with the assistance of individual computerized temperature pointers cum coblontrollers. Both the squares are appropriately protected to dodge warm misfortunes..

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering educational equipments india, engineering equipments distributors, engineering lab instruments, engineering equipments manufacturer, thermodynamics engineering equipment, engineering educational lab equipments in Ambala, India. 


Tension Set Apparatus

RTE-0020

Pressure Set Apparatus - Tension set is characterized as the extent of connected strain staying after an elastic piece has been extended and permitted to recuperate in determined way. It is an imperative property for elastic parts that are subjected to tractable anxieties either persistently or irregularly. and Tension set is controlled by extending a test example of standard measurement by a predefined rate in an appropriate mechanical assembly for a predetermined time and temperature and afterward enabling it to recoup. It is shown as lasting set held by the test example communicated as a level of starting strain given to it. common lab supplies makers.

Contact Ray Export for your School, College Civil and Mechanical Engineering Lab Instruments. We are the best engineering lab equipments, engineering equipment manufacturer india, engineering equipment india, chemical engineering lab equipments, control engineering laboratory equipments, control engineering laboratory equipment, control engineering lab equipment in Ambala, India. 

Supply of Rubber Testing Equipment from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }