Quick answer. This listing holds 41 instruments, TE-0001 to TE-0041, and they fall into five families that have little to do with each other: environmental and stability chambers (walk-in incubator, stability and photostability chambers, environmental chamber, corrosion autoclaves), hardness and compression set testing of flexible materials (three indentation hardness testers, compression set apparatus, foam pounding tester), surface and fastness testing (crock meter, rotating drum abrasion, pilling tester, vamp flex tester), water and analytical instruments (pH meters, spectrophotometer, nephelometer, ion-specific meters, water and soil analysis kits), and thermal and fluid test rigs (Pelton turbine, wind tunnel, compressor and refrigeration rigs, composite walls apparatus). If you want one thing from this page, take this: for a chamber, the specification that matters is not the temperature range it reaches but the uniformity and fluctuation it holds across a loaded working volume.
Chambers are the largest coherent family in this listing and the one where buyers are most often sold the wrong specification. Every chamber datasheet leads with a temperature range and a humidity range. Those are the two numbers that matter least.
A chamber does one job: hold a defined condition, everywhere inside it, for as long as the test runs, with the load in place. Four specifications describe whether it can, and you should ask for all four in writing:
Two further points that decide whether a chamber survives an audit:
Mapping. A chamber used for work anyone else relies on should be mapped - multiple sensors distributed through the working volume, logged over a period, loaded and empty - and re-mapped periodically and after any relocation or repair. Mapping is a service, not a feature of the box, and it should be budgeted at purchase rather than discovered at the first inspection.
Recording and alarms. For any study that runs for weeks, the record is the deliverable. Ask what is logged, at what interval, where it is stored, whether the log can be exported in a form you can archive, and what happens if the power fails at two in the morning: does the chamber restart at its set point, and is there an alarm that reaches a person? A stability study with a gap in its record has a gap in its conclusion.
The photostability chamber deserves a specific note: it controls light exposure as well as temperature, so the specification includes the lamp type, the illumination and the near-ultraviolet energy delivered, plus lamp hours and a replacement schedule. Lamps age and their output falls. A photostability chamber without a lamp-hours record is delivering an unknown exposure.
This listing holds three indentation hardness testers, including one for polyurethane foam, plus compression set apparatus and a repeated compression set tester. These measure something fundamentally different from the metal hardness testers in our metal testing machines range, and the difference is worth stating plainly because the word "hardness" hides it.
On metals, hardness is resistance to permanent indentation, and the result is read from the size or depth of a permanent impression. On foams and elastomers, there is no permanent impression - the material recovers. What is measured instead is the force needed to indent the surface by a specified amount with a specified indentor, or the indentation produced by a specified force. The result therefore depends on:
Compression set is a separate question: how much permanent deformation remains after the material has been held compressed by a specified amount, at a specified temperature, for a specified time, and then allowed to recover for a specified period. All four of those numbers are part of the result. The repeated compression set tester and the pounding tester answer the durability version of the same question, cycling the load rather than holding it, which is closer to what a cushion actually experiences.
A caution on this group of records: three indentation hardness testers appear in this listing under names that differ only by a word. They are genuine variants - analog, and a version configured for polyurethane foam - but the names do not make the difference clear, and we are rewriting them so that a buyer can tell which is which without asking.
The crock meter tests colour fastness to rubbing - whether colour transfers to a dry or wet rubbing cloth - and it is the instrument behind most complaints about a garment marking skin or upholstery. The rotating drum abrasion tester measures wear resistance of rubber by a different principle from the rotary platform abrasers used on textiles. The pilling tester produces the surface fuzzing and bobbling that customers notice before anything else about a fabric. The water vapour absorption tester addresses comfort properties.
All four share one requirement that is easy to overlook: the rubbing cloth, the abrasive wheel, the abradant fabric and the standard reference material are consumables, and they are the test. A crock meter with a batch of rubbing cloth from an unspecified source is not running the method, and an abradant that has been used past its service life gives results that drift in the flattering direction. Buy the specified consumables with the instrument, record the batch on the test report, and treat them as a recurring cost.
Textile and leather testing is covered in depth in our fabric testing equipment and footwear testing equipment ranges, and paper and board in paper and packaging testing equipment.
The pH meters, spectrophotometer, nephelometer, ion-specific meters and water and soil analysis kits in this listing serve environmental and agricultural laboratories, water utilities and teaching laboratories. One point governs all of them.
An analytical instrument is only as good as the standards you calibrate it with, and most of the running cost is in consumables rather than the instrument. For pH, the electrode is a wearing part with a finite life - typically a year or two in routine use, shorter in dirty or hot samples - and it must be calibrated against fresh buffer solutions, at the temperature of measurement, across the range you work in. A pH meter that reads to two decimal places and is calibrated with old buffers is precisely wrong. For turbidity, the result depends on the calibration standards and on their preparation. For spectrophotometry, wavelength accuracy needs periodic verification against a reference.
So when you enquire, tell us your sample matrix and your throughput, and ask us for the consumable list and its expected life alongside the instrument price. We will give you both figures; the second one is usually the larger over five years.
The Pelton turbine test rig, wind tunnel, single and double stage air compressor rigs, refrigeration test rig, composite walls apparatus and air flow tester in this listing are teaching and research rigs rather than testing instruments. They belong with the mechanical and thermal engineering range, and our engineering apparatus and civil engineering lab equipments categories cover that work in depth.
One point has to be raised before any refrigeration or air conditioning rig is ordered, and we raise it at the enquiry stage rather than at the border: ask which refrigerant the rig is charged with, and whether that refrigerant may lawfully be imported, sold and serviced in your country. Refrigerants are controlled internationally under the Montreal Protocol and its Kigali Amendment, national phase-down schedules differ, and a rig charged with a refrigerant your market is phasing out is a rig you cannot service in a few years even if you can import it today. Tell us the destination country and we will confirm the charge in writing. The same question applies to the gas in any sealed-system demonstration apparatus.
The lyophilizer in this listing is a freeze drying system - a preparation and process instrument used in pharmaceutical, food and biological work rather than a test instrument. We supply it; it is simply filed in the wrong place, and we have flagged that.
| Family | In this listing | The specification that decides it |
|---|---|---|
| Environmental and stability chambers | Walk-in incubator, stability chamber, photostability chamber, environmental chamber, corrosion autoclaves, cold insulation tester | Uniformity and fluctuation under load, recovery after door opening, mapping and logging |
| Flexible-material hardness and set | Three indentation hardness testers, compression set apparatus, repeated compression set tester, pounding tester | Indentor geometry, specified indentation or force, dwell time, specimen thickness, temperature |
| Surface, fastness and abrasion | Crock meter, rotating drum abrasion tester, pilling tester, water vapour absorption tester, vamp flex tester | The specified consumable - rubbing cloth, abradant, abrasive wheel - and its batch record |
| Water and analytical | pH meters, spectrophotometer, nephelometer, ion-specific meters, water and soil analysis kits | Calibration standards and electrode life; the consumable budget, not the instrument price |
| Thermal and fluid test rigs | Pelton turbine, wind tunnel, compressor rigs, refrigeration rig, composite walls apparatus, air flow tester | Instrumentation supplied with the rig, and for refrigeration, the refrigerant charge and its legality in your market |
A note on this listing, published rather than hidden. This category is a catch-all. Its 41 records span textile, footwear, foam, rubber, rock, water, pharmaceutical, electrical machine and thermal engineering work, and no single subject describes it; we have described the families instead. Specific observations we have flagged for correction: the stability, photostability, environmental and walk-in chambers are a substantial product family that deserves its own category, because buyers search for them by name and they are currently invisible inside a general listing; a Doppler radar training system and several teaching rigs sit in a testing category while a peel strength tester sits in a category named for trainers; a lyophilizer is a process instrument rather than a test instrument; one product name carries the padding phrase "for Research Institutes", which we are removing as we are removing similar padding elsewhere; "pH" is written in lower case in two records; and a compression set apparatus appears both here and in our general testing index, which needs a database check rather than a guess.
Related ranges: soil testing machines, concrete testing machines, and the full testing machines category.
Uniformity is the spread between different points inside the chamber at the same moment; fluctuation is the variation at one point over time. A chamber can be excellent at one and poor at the other. Uniformity decides whether every specimen experiences the same condition, and it is the figure most often missing from a quotation. Ask for both, determined over a stated period, and ask whether they were determined empty or loaded.
If your results are only for internal development, the factory certificate may be sufficient. If they go to a customer, a regulator or an auditor, you will be asked for a mapping report for the chamber as installed, with the load you actually use, repeated periodically and after any move or major repair. Budget it at purchase. A chamber bought without a mapping plan is usually mapped in a hurry during an inspection.
Because it measures a different quantity. Metal hardness is read from a permanent indentation; foam and elastomers recover, so what is measured is the force for a specified indentation, or the indentation under a specified force, at a specified dwell time. The indentor geometry, the dwell and the specimen thickness are all part of the result, and a metal hardness tester cannot produce that measurement.
In routine laboratory use, commonly one to two years, and less in hot, dirty or high-solids samples or if it is allowed to dry out. It is a wearing part, not a permanent fitting. Judge it by its response: an electrode that drifts, responds slowly or will not calibrate against fresh buffers has reached the end of its life regardless of its age. Order a spare with the meter, and keep fresh buffers rather than economising on them.
Tell us the destination first. Refrigerants are controlled internationally and national phase-down schedules differ, so a charge that is routine in one market may be restricted in another, and a rig you cannot service locally in a few years is a poor purchase even if it clears customs today. We will confirm in writing which refrigerant a rig is charged with so that you can check it against your own regulations before ordering.
Because this category was used as a catch-all as the catalogue grew. We have said so above rather than writing copy that implies a coherence it does not have, described the families as they are, and flagged the chambers in particular to be given their own category. If you tell us what you are testing we will point you to the right range in one reply.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
The contents of this listing were read live on 15 October 2026 across all five of its listing pages. Electrode life, chamber behaviour and consumable guidance above are general method and practice, not specifications of a particular model; figures for any model we quote will be given in writing. Regulatory requirements for refrigerants, lamps and analytical reagents differ by country and must be checked against your own national rules before ordering.
Water Vapor Absorption Tester - The heaviness of water vapors consumed by an example of calfskin is controlled by settling a round bit of cowhide over a barrel shaped pit in a metal holder having refined water inside it. The test example is held immovably against the lip of the pit and permitted to interact with the vapors left off by the water for a predefined timeframe. The put on in weight of the test example on account of assimilation of vapors by it is resolved, from which the estimation of Water Vapor Absorption is ascertained. &civil lab types of gear producers.
Water Testing Kit: (Drinking/Agriculture/Fisheries) Water assumes a vital part in the lives of living being. The nature of water expended for different reason should be checked before physical utilize. Different imperative utilizations of water are of Agriculture, Fisheries, Aquarium and Drinking Water. Parameters: Drinking: pH Turbidity TDS Hardness Chlorides Residual Chlorine Iron Nitrates Fluoride Arsenic Bacteriological Test Agriculture: pH E.C Hardness Chloride Alkalinity Fisheries: pH TDS Hardness Alkalinity CO2 DO Nitrities Ammonia Phosphate common lab types of gear producer. , Water Testing Kit Lab hardware manufacturers,exporters and Water Testing Kit Lab providers
Vamp Flex Tester Low Temperature Model - The Vamp Flex Tester is utilized for evaluating the inclination of shoe uppers and coating materials to split or fizzle at the flexing wrinkles framed in the upper amid strolling. and In this test, square formed test examples are held at their contrary edges in two reversed V-molded braces having their holding faces in a similar plane. One of the cinches is kept settled while the other is made to move towards it and back over and again, delivering splits like those shaped in the vamp of the shoe. This procedure is rehashed ceaselessly and the state of the test examples checked after various determined number of flexing cycles till disappointment happens. For leading protection from hydrolysis the test examples are molded in immersed water vapor climate by keeping them in a dessicator above water for seven days at 70°C, trailed by molding under a standard temperature for 24 hours before directing the flexing test at - 5°C. common lab types of gear makers.
Pelton Turbine Test Rig Test fix comprises of a Pelton wheel water Turbine, intended for research facility exploratory purposes and to direct test in metric units. The setup comprises of a Pelton turbine coupled to a rope brake dynamometer. A diffusive pump supplies water at high weight to the turbine unit.The turbine comprises of a cast press body with an expansive straightforward acrylic window, a spout and lance course of action, a rotor get together of shaft, sprinter and a brake drum all mounted on a durable base casing. The pelton pails and spout are made of gunmetal and the lance made of metal for erosion protection. The contribution to the turbine is controlled by changing the lance position with a hand wheel. The straightforward perspex sheet side packaging is accommodated visual perception of stream on the pails. The power created by the turbine is absored by the rope brake dynamometer. Instruments are given to quantify the info water stream rate & weight and additionally speed & torque. Trial Capabilities: To gauge control created by Pelton Turbine. To figure meachanical proficiency of the Turbine. To plot execution bended for Pelton Turbine. Specialized Specifications: Pelton Turbine: Design Speed - 1000 RPM. Yield Power - 1.0 KW Dynamometer: Rope brake dynamometer coupled to the turbine Pump: Centrifugal monoblock pump, Capacity 5 hp, 440Volts, 3 Phase, 50 Hz with DOL Starter Water stream estimation: Venturimeter with weight taps associated with two weight checks Storage tank: Made in MS, FRP Lined for rust assurance Spring balance: 0-50 Kg, for torque estimation Tachometer for Speed estimation .
Specialized Description » For assurance of protection offered by shake to weathering and breaking down when subjected to submersion in water. » Facility to test upto four arrangements of tests » Quick coupling for get together and expulsion of drums and The gear comprises of: and Base Board with Motor Drive gathering with tow drum and tank congregations. Reasonable for working at 220 V, Single Phase, AC supply. Supply with Electric clock, 0-30 min. and Optional Accessories and Pair of Drums and Tank Assemblies,&including coupling, to empower upto 4 test drums to be driven at once and Electrical Timer,&0-30 min. mechanical lab types of gear producers and.
ounding Tester - We offer Pounding Tester, which is utilized to test the pressure of froth. The impact of rehashed use of weight on the surface of a piece of polyurethane froth experienced in its ordinary life is assessed by mimicking these conditions in research center by applying and discharging a predetermined power for a predefined number of times, after which the impact of such beating on the physical attributes, for example, hardness file, thickness, and cell structure are seen to assess the nature of froth chunk. common lab types of gear producers.
Vicat Softening Point Apparatus High Temperature - Vicat softening temperature of plastics is the temperature at which a standard level finished indentor infiltrates 1 mm into the surface of the material under test under a predefined stack. The test is directed by putting a test example taken from the example under test on a level stage inside a fluid shower and applying pressure stack over its upper face through a level finished indentor. The heap is connected by setting dead weights on the upper end of the indentor. After the test example accomplishes the temperature of the shower, the shower temperature is expanded steadily till the indentor infiltrates by precisely 1 mm into the test example. The shower temperature in degrees centigrade at which this happens is accounted for as the Vicat Softening Temperature of the example under test. and The& Vicat Softening Temperature Apparatus for plastics comprises of a pivoted metallic edge which fills in as help for the test example. The edge is fitted with a shrub for managing a pole with a solidified indenting tip at its lower end and a stacking stage close to its best to put the weights on. A dial check is fitted at the upper end of the edge to quantify the development of the bar. The parts that are submerged in the shower amid the test are produced using metal. The indentor is produced using rapid steel. common lab types of gear producers and. Plastic Films Testing Lab gear manufacturers,exporters and Plastic Films Testing Lab providers
Pilling Tester - Pilling Tester is a texture surface blame portrayed by little pills of trapped strands sticking to the surface. These are shaped amid wearing or washing by the entrapment of the free strands, which distend from the texture surface, and advancement of these into round groups tied down to the texture by a couple of unbroken filaments. These give an unattractive look to the pieces of clothing. and To decide the propensity to frame pills, test examples taken from the texture test are rubbed against each other under controlled conditions and the presence of the test example in the wake of rubbing for the predefined period is thought about against standard rating photos for reviewing the texture under test. and Technical Data Inside measurements of wooden boxes : 225 x 225 x 225 mm and Thickness of stopper lining :3 mm and Speed of revolution of boxes : 60 rpm and Dimensions of elastic tubes : 32 external breadth 25.5 inside width 140 mm length and Motor :frac14; HP, single-stage, 230 volts AC and Counter : 5 digit pre-set compose electronic counter.
Space Hardness Tester - The vibe of delicate quality of any adaptable froth is quantitatively characterized by its space hardness. Space hardness is controlled by squeezing a roundabout indentor at a predetermined speed against a piece of froth and finding the power expected to pack the square to a predefined level of its underlying thickness. and The Indentation Hardness Tester for polyurethane froth seats comprises of a roundabout steel indentor that can be squeezed against the test example kept on a level flat surface at a predetermined speed with plan to quantify the heap being connected by the indentor on the test example, course of action to gauge the thickness of the test example toward the beginning of the test under a predefined load, and game plan to stop the development of the indentor consequently after the coveted diversion..
A.C Alternator And Synchronous Generator We are one of the presumed A.C Alternator or Generator providers and producers from India. These alternators are produced utilizing the superb crude materials guaranteeing the toughness, unwavering quality, high rigidity and protection from erosion. Our Generators are precisely outlined by our talented designers so as to meet the particular client’s necessities. These alternators are acknowledged for their support free execution, tough administration, high quality and conservative outline D.C Motor combined with A.C Alternator (Non-Salient shaft or Rotating arm compose) Bearings accessible in a bad position free and longer life tasks Permeability steel in top-notch used to make external burdens. For the relentless execution, the ideal quality copper channels of protected materials are utilized As a part of the request to have low clamor we planned these in Tilted development rotors with correct adjust. Non remarkable compose and settled shaft write spinning armatures To keep away from any kind of incident amid tasks, exceptional gatekeepers are fitted on the couplings D.C Motor Shunt/Compound 5HP Coupled with A.C Alternator 3KVA (Separately of self Excited) D.C Motor Shunt/Compound 2HP combined with A.C Alternator 1KVA (Separately or self Excited) D.C Motor Shunt/Compound 3HP combined with A.C Alternator 1.5KVA (Separately of self Excited) The D.C engine settled with alternator can be utilized for following tests. To gauge the zero and negative succession response of synchronous machines. To gauge the quadrature pivot and direct hub response of an alternator. To gauge the quadrature and sub-transient direct pivot reactio0n of remarkable shaft machines.
Login
Register
+91 9817319615
