science lab equipment manufacturer

Theory of Machines Lab

Theory of Machines Lab Lab Equipment Manufacturer, Supplier and Exporter in India

Ray Export is a leading manufacturer and supplier of Theory of Machines Lab in India,

Theory of Machines Lab

Quick answer. This is the experiment range for a dynamics of machines laboratory - motorised, instrumented rigs on which a student varies something and measures the result: gyroscope, governors, journal and tilting pad bearings, whirling of shaft, universal vibration, cam analysis, static and dynamic balancing, slip and creep. Codes run TML-0001 upwards across about 110 records. It is not the same range as our demonstration models, which are coded TOM- and listed under models - theory of machines; those show a mechanism moving, these produce a graph. The test to apply to any rig on this page is the one in the next section: what can you vary, and what can you measure while you vary it?

What the rig must let you vary

A dynamics apparatus that can only be switched on gives a class one observation. The same apparatus with an independent variable and a measurement chain gives them a graph, a gradient and a comparison with theory - which is the whole point of the laboratory. So before capacity, finish or price, ask what the rig lets you change and what it lets you read. For every experiment in this range there is a specific answer:

ApparatusWhat you varyWhat you measureThe result the experiment exists for
Motorised gyroscope (TML-0001)Applied couple, and spin speedRate of precession, spin speedThat precession rate is proportional to the applied couple and inversely proportional to spin - verified, not asserted
Universal and motorised governor (TML-0007, TML-0010)Speed, and sleeve load or spring rateSleeve lift against speedThe characteristic curve of each governor type, and the difference between them on one frame
Journal bearing (TML-0002)Load, speed, oil grade and temperaturePressure at tappings around and along the bearingThe pressure distribution that hydrodynamic theory predicts, and how it collapses as speed falls
Michell tilting pad bearing (TML-0008)Load and speedPad tilt and film pressureWhy a pad that is free to tilt forms a converging film at any speed
Whirling of shaft (TML-0003)Speed, shaft diameter and length, end fixingAmplitude against speedCritical speed, and how end conditions move it
Universal vibration (TML-0004)Exciting frequency, mass, stiffness, dampingAmplitude and phase against frequencyResonance, and the effect of damping on the peak - the most transferable result in the subject
Cam analysis (TML-0005)Cam angle, cam and follower type, spring loadFollower displacement, and jump speedThe displacement diagram measured rather than drawn, and the speed at which the follower leaves the cam
Static and dynamic balancing (TML-0006)Mass, radius and angular position of each weightResidual vibration or reaction at the bearingsThat static balance does not imply dynamic balance - the result students remember
Slip and creep (TML-0009)Belt tension and loadDriver and follower speedsThe distinction between slip and creep, which a formula alone never makes clear

We put this table first because it is the fastest way to tell a well-specified rig from a cheap one. Two rigs can look identical in a photograph and differ entirely in whether the independent variable is adjustable and calibrated. A governor with a fixed spring teaches one curve; a governor with interchangeable springs and a scale on the sleeve teaches the family of curves, which is the syllabus.

The measurement chain is where these experiments are won or lost

Almost every experiment above reduces to one of three measurements, and each has a characteristic failure.

Speed

Speed appears in nearly every result on this page, and in the gyroscope and whirling experiments it appears squared or cubed, so an error in speed is magnified in the answer. Specify how speed is measured and insist on a second, independent means of checking it. A contact or optical tachometer reading the shaft directly, cross-checked against the drive setting, is the minimum. Where a stroboscope is used, it must be used with discipline, and a laboratory that owns only a stroboscope and no second instrument will eventually publish a speed that is a simple multiple of the truth.

Amplitude

In the vibration and whirling experiments the quantity of interest is a small displacement of a moving part. Ask what measures it: a dial gauge is useless on a vibrating member, a mechanical drum recorder gives a trace a class can see and measure, and a transducer with a logger gives frequency and phase as well as amplitude. The answer determines which experiments the rig can actually support - phase against frequency, which is where the physics of resonance lives, needs a transducer.

Force, couple and reaction

In the gyroscope, balancing and bearing experiments the measured quantity is a force or a reaction. Dead weights on a known arm are simple, honest and visible, and for teaching they are often better than a load cell because the student can see what is applying the couple. Where a load cell is used, ask how it is calibrated and whether a dead-weight check is possible, because an uncalibrated electronic reading is the easiest thing in a laboratory to believe and the hardest to check.

Guarding, anchoring and the stop button

These are motorised rigs with exposed rotating masses, and several of them are deliberately run into a condition the rest of engineering avoids. Three requirements apply to the whole range and should be on the order, not negotiated after delivery:

  • A guard that is in place when the rig runs, over any rotating mass, belt or flywheel. On the balancing rig this matters more than it looks: the rig is run deliberately out of balance, and an out-of-balance rotor throws anything that is loose.
  • A fixing to the floor or a bench of sufficient mass. An unanchored rig with an out-of-balance rotor walks across the floor, and the walking itself corrupts the reading, because the frame is then part of the vibrating system.
  • An emergency stop within reach of the operator, and a stated maximum speed with the drive limited to it. On the whirling rig the limit is not advisory.

One practical point about the bearing rigs that nobody mentions until the first session: they leak. Oil on a laboratory floor is the most likely injury in this range. Ask for a drip tray with the rig, decide where waste oil goes before the first experiment, and keep absorbent granules in the room.

Specifying the governors, because this is where syllabuses differ

Governors are the experiment most often bought wrongly, because the catalogue word "universal" covers several arrangements and a syllabus usually names specific ones. The arrangements a mechanical engineering course normally requires are the simple pendulum type, the loaded type with a central weight, and the spring-loaded type, and what the student is asked to produce is a curve of sleeve lift against speed for each, compared with each other.

So ask three questions: which arrangements can be set up on the frame supplied; is the change-over a conversion the laboratory can do inside a practical session, or a rebuild; and is there a scale on the sleeve, since a lift that has to be estimated by eye produces a scatter plot rather than a curve. For the spring-loaded arrangement, ask whether more than one spring rate is supplied, because the effect of spring stiffness on the governor characteristic is a standard exercise and it cannot be done with one spring.

What to tell us when you enquire

  • Your experiment list as the syllabus words it. These rigs map onto named experiments, and we would rather match the list than guess from a category.
  • Group size and session length. A rig that takes most of a practical to set up suits a demonstration, not a rotation of six groups.
  • What instrumentation the laboratory already owns - tachometer, transducers, logger, stroboscope - because the sensible purchase is often a rig specified to accept what you have.
  • Floor or bench mounting, and whether the room can take an anchored rig.
  • Supply voltage and frequency, destination country, and whether a drip tray and oil are to be supplied.

Related ranges: models - theory of machines for the demonstration models that accompany these experiments, engineering training models for mechanism and linkage models, S.O.M. lab for strength of materials, structural mechanics lab, engineering gear models, and hydraulics and fluid mechanics trainers. The full mechanical lab equipments category lists the rest of this branch.

Frequently asked questions

How is this range different from your theory of machines models?

The models, coded TOM-, show a mechanism moving so that a student can see how it works. The apparatus on this page, coded TML-, is instrumented so that a student can vary a quantity and measure the consequence. A laboratory teaching the subject properly wants both: the model makes the mechanism intelligible, and the rig turns it into a measurement. If your budget covers only one, buy according to what your assessment requires - a laboratory report needs data, a lecture needs a model.

Why does the balancing experiment matter so much?

Because it produces the result students find least intuitive: an assembly can be perfectly balanced at rest and shake violently when it rotates. Static balance requires the resultant force to vanish; dynamic balance also requires the resultant couple to vanish, and two equal masses set at opposite ends of a shaft and 180 degrees apart satisfy the first and fail the second. Measuring the bearing reaction makes that unavoidable, which is why it belongs in a laboratory rather than a lecture.

What makes the whirling of shaft experiment different from the others?

It is the one experiment in the laboratory where the machine is deliberately run at its own critical speed, so the amplitude grows while the student watches. That is exactly why it teaches well, and exactly why the guard, the anchorage, the stated maximum speed and a drive limited to it are not optional. Ask us for the maximum speed in writing and make it part of the standing instruction for that rig.

Can we run the journal bearing experiment without a heater or oil temperature measurement?

You can take readings, but they will not be comparable from one session to the next. Oil viscosity falls steeply with temperature and viscosity is in the theory, so the oil grade and the oil temperature are part of the result and belong on the report form. If the rig has no temperature measurement, add one; if the laboratory is hot in the afternoons, expect the morning and afternoon groups to disagree until the temperature is recorded.

Do these rigs come with experiment manuals?

Ask per item and get the answer in writing before ordering. For a teaching laboratory the manual - the procedure, the theory, the observation table and a worked example - is a substantial part of the value, and it is the thing most often missing. If a manual is not supplied, budget staff time to write one, because a rig without a procedure tends to sit unused after the member of staff who understood it moves on.

Can one rig cover several experiments?

Sometimes, and it can be a false economy. A universal vibration frame genuinely supports many experiments and is good value. A single frame that must be rebuilt between experiments costs session time every week for the life of the rig, and in a laboratory with six groups rotating it becomes the bottleneck. Tell us your session length and group count and we will say which combination is sensible rather than which is cheapest.

Key takeaways

  • Buy the variable, not the rig. Ask what each apparatus lets you change and what it lets you read; a rig with a fixed parameter teaches one point instead of a curve.
  • Speed errors are magnified. Speed appears squared or cubed in several results here, so specify how it is measured and keep a second independent instrument to check it.
  • Amplitude measurement decides which experiments are possible. Phase against frequency needs a transducer; a dial gauge cannot do it.
  • Guard, anchor, and limit the speed. These rigs run exposed rotating masses, and the balancing rig is run deliberately out of balance.
  • Bearing rigs leak. Specify a drip tray and decide where waste oil goes before the first session.
  • Governors need more than one spring and a scale on the sleeve, or the standard exercises cannot be run.

About this page

Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.

Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.

Notes on this listing, published rather than hidden: the tilting pad bearing is named after A.G.M. Michell and the record spells it "Michel" - we are correcting it, and we print the correct spelling here because it is the word a specifier will search for. One record ("Cam Analysis Apparatus-") carries a stray trailing hyphen in its name. This category covers the same subject as our TOM- coded models range under a different parent; the two hold different products with different codes, and we have recommended that the relationship between them be made explicit in the site structure rather than left for a visitor to work out. Specifications are confirmed in writing on the quotation; for certificates and standards, contact us for the latest copies of the relevant certificates before tender submission.

Motorised Gyroscope Apparatus

TML-0001

The set up comprises of substantial stainless steel circle mounted on a flat shaft, pivoted by a variable speed engine. The rotor shaft is coupled to an engine mounted on a trunion outline having direction in a burden outline, which is allowed to pivot about vertical hub. A weight skillet on opposite side of plate adjusts the heaviness of engine. Rotor circle can be move around three hub. Torque can be connected by computing the weight and separation of weight from the focal point of rotor. The gyroscopic couple can be resolved. 


Extent OF EXPERIMENTATIONS: 


Exploratory legitimization of the condition T = l w. wp for computing the gyroscopic couple by perception and estimation of results for free vibrations in connected couple T and precession wp. 


To contemplate the gyroscopic impact of a turning plate. 


bservation of gyroscopic impact of pivoting circle. 


UTILITIES REQUIRED: 


Electric supply 


230 V AC, Single Phase. 


Seat region 


1m x 1m 


Tachometer to discover RPM of circle. 


Specialized DETAILS: 


Plate 


Material Stainless Steel 


Dia 300 mm x 12 mm thick exactly adjusted which can be turned in 3 commonly opposite hub. 


Engine Variable speed of standard make. Provided with Speed Control Unit. 


Weights 2 kg, 1 kg, ½ kg.. 


Stop Watch Electronic 


Precisely stamped scale and pointer to gauge precession rate.

Journal Bearing Apparatus

TML-0002

Diary bearing mechanical assembly to investigate the circulation of weight in slide heading represents the guideline of hydrodynamic grease. The dissemination of weight and the conveying limit can be resolved on a sliding bearing model at various bearing burdens and speeds. The sliding bearing comprises of a course diary driven by an electrical engine and the uninhibitedly moving bearing lodging. The bearing is stacked with various, exchangeable weights. To see the moving of the bearing diary in activity as unmistakably as would be prudent, the model has a huge hole and a straightforward lodging. Both the spiral and hub dissemination of weight can be recorded in the bearing hole at 12 estimating focuses around its border and four along the length. The estimations are appeared by methods for 16 tube manometers mounted on a board. The framework is mounted on a moving help and is appropriate for exhibit and additionally for use in research facility tests

Whirling Of Shaft Apparatus

TML-0003

At the point when the characteristic recurrence of a framework concurs with the outside driving framework recurrence the wonder is called reverberation. The speed at which reverberation happens is known as basic paces. These rates are likewise called spinning velocities or whipping.. 


Extent OF EXPERIMENTATIONS:- 


(1) Supported end conditions: Make utilization of end obstructs with single self-adjusting bearing. 


(2) Fixed end conditions: - Make utilization of end obstructs with twofold bearing. The gatekeepers D1 and D2 can be settled at any situation on the supporting bar outline, which fits on side help F. Turning shafts are to be fitted in obstructs in A &B stands. . 


UTILITIES REQUIRED:- 


The driving engine is 230V DC 1/16 


H.P; 6500 RPM. A dimmer condition of 240v, 2amp, and 50 cycles is utilized to control speed of the turning shaft. 


EQUIPMENT? DETAILS :- 


(A)???? Coupling: - An adaptable shaft is utilized to drive the test shaft from engine. 


(B)???? Ball bearing settling closes:- The closures settle the pole while it turns. The pole and the end-settling gadget can be supplanted inside a brief timeframe with the assistance of this unit. The settling closes give change of end settling state of the turning shaft according to the prerequisite.

Universal Vibration Apparatus

TML-0004

The mechanical assembly gave exhaustive unit to play out the vibration tests. An all inclusive edge is given whereupon fast and simple get together of different trials should be possible. The unit is independent to securely store saves. The understudies can without much of a stretch gather the trials and concentrate the hypothesis of vibrations basically. 


Extent OF EXPERIMENTATIONS: 


Following tests can be performed with this unit: 


· To confirm the connection basic pendulum. 


· To confirm the connection of compound pendulum and to decide the span of gyration. 


· To think about span of gyration of bi-filar suspension. 


· To contemplate the undamped free vibration of spring mass framework. 


· To contemplate the longitudinal vibration of helical looped spring. 


· To contemplate the constrained vibration of basically upheld bar for various damping. 


· Undamped torsional vibrations of single rotor framework. 


· Undamped torsional vibrations of twofold rotor framework. 


· To consider the damped torsional vibration of single rotor framework and to decide the damping co-productive. 


· Verification of Dunker ley's Rule. 


· To consider the constrained damped vibration of spring mass framework. 


UTILITIES REQUIRED: 


· Floor Space: 2.5 m x 2.5 m approx. 


· Power Supply: 230V AC, 5 Amp. with earth. 


Specialized DETAILS: 


· RPM estimation 


o Digital RPM Indicator with Proximity sensor. 


· The set-up likewise comprises of exciter unit with FHP Motor and speed controller, standard strip graph recorder and damper with course of action for evolving damping. An electronic stop clock is given to gauge the day and age.

Cam Analysis Apparatus-

TML-0005

Mechanical assembly is a mechanized unit comprising of a camshaft driven by a variable speed engine. The pole keeps running in a twofold bearing. The free end of the camshaft has an office to mount the cam effectively. 


The supporter is legitimately guided in gunmetal brambles and the sort of devotee can be changed by the cam under test. Graduated roundabout protractor is fitted co-pivotal with the pole. Furthermore, a Dial Gauge fitted on the devotee shaft is utilized to take note of the adherent relocation for the point of cam turn. A spring is utilized to give controlling power to the supporter framework. Weights on the devotee shaft can be balanced according to the prerequisite. A game plan is given to manage the speed. The contraption is extremely helpful for testing the cam execution for bounce marvel amid activity. On this contraption the impact of progress of latency powers on hop activity of cam-adherent amid task can be watched. It is valuable for testing different cam and adherent sets. Three cams and three devotees will be provided with the device. Proposals are now solidified to lessen the wear. 


Extent OF EXPERIMENTATION: 


With the assistance of blend of gave cams and supporters following investigations can be directed: 


To plot the n-q (Follower removal Vs Angle of turn) bends for various cam supporter sets 


The supporter skip can be seen by utilizing a stroboscope (Optional) and impact of devotee weight on ricochet can be contemplated. 


To contemplate the impact of adherent weight on skip. 


To contemplate the impact of spring pressure on ricochet. 


The tests can be rehashed by changing pressure springs, adherent weights and cam speed. 


UTILITIES REQUIRED: 


Power 0.5 kW, 220 V, Single Phase 


Stroboscope (Optional). 


Specialized DETAILS: 


Cam Shaft Material Stainless Steel 


Cams Tangent, Eccentric, Circular Arc write. 


Adherents 


Roller, Knife edge, Mushroom 


Pressure Spring 


Given Weights 1 kg., 500gm, 200 gm and 100gm 


Engine Variable speed, ½ HP., 0-1500 RPM with speed controller 


Dial Gauge Baker and Mercer/Standard Make

Static & Dynamic Balancing Apparatus

TML-0006

This gear is intended for doing the investigation for adjusting a pivot mass framework. The contraption comprises of a stainless steel shaft settled in a rectangular edge. An arrangement of four squares with a clasping game plan is given. For static adjusting, each square is independently clipped on shaft and its relative weight is discovered utilizing line and compartment framework regarding number of steel balls. For dynamic adjusting, a minute polygon is drawn utilizing relative weights and precise and pivotal position of pieces is resolved. The piece are cinched on shaft is turned by an engine to check dynamic adjust of the framework. The framework is furnished with precise and longitudinal scales and is suspended with chains for dynamic adjusting. 


Extent OF EXPERIMENTATIONS: 


· To adjust the majority statically and powerfully of a solitary turning mass framework. 


· To perception of impact of unbalance in a pivoting mass framework. 


UTILITIES REQUIRED: 


· Electricity 0.5 kW, 220 V, Single Phase 


Specialized DETAILS: 


· Drive Motor 


o FHP Motor, variable speed, with speed controller. 


· Balancing weight 


o 4 Nos. of Stainless Steel with various measured unusual mass for changing unbalance. 


· Rotating Shaft 


o Material Stainless Steel

Universal Governor Apparatus

TML-0007

The set-up is intended to think about the working of various governors ordinarily used to control the speed. It comprises of a principle shaft, mounted vertically on the base plate. This shaft is driven by a variable speed Motor which is additionally mounted vertically on a similar base plate. Any one representative gathering out of four can be mounted on axle. The axle speed is controlled by speed control unit. A graduated scale is fitted to the sleeve to gauge the removal. 


Extent OF EXPERIMENTATIONS: 


Assurance of trademark bend of a sleeve position against speed of pivot for all governors. 


To contemplate the impact of changing the mass of the middle sleeve in Porter and Proell Governor. 


To contemplate the impact of differing the underlying spring pressure in Hartnell Governor. 


To examine the assurance of attributes bends of sweep of revolution against controlling power (Actual and Theoretical) for all governors. 


UTILITIES REQUIRED: 


Power Supply 230 V AC, Single Phase. 


Floor Space 1.5 x 1.5 m 


Tachometer to discover RPM. 


Specialized DETAILS: 


Axle Material Stainless Steel 


Representative Mechanism Four distinct sorts of senator instrument with spring and weights. 


Watt Governor Porter Governor 


Hartnell Governor Proell Governor 


Engine Variable speed, Standard Make, FHP Motor. 


Control Panel For speed control of engine

Michel Tilting Pad Bearing Apparatus

TML-0008

The device comprises of a cushion, which can be tilted to the required point. An unending belt, which moves underneath the cushion, conveys the oil over its surface from oil shower. At the point when the cushion is tilted over the oil movie, weight is produced, the cushion is furnished with weight recordings parallel and opposite to belt course. The weight conveyance is estimated over a multi tube manometer. The belt is driven by a variable speed engine. The tilting edge and least hole amongst cushion and belt can be balanced and qualities in this way can be learned at different holes, slant and relative surface rates. 


Extent OF EXPERIMENTATIONS: 


Exhibit of weight advancement. 


Plotting weight variety bend in longitudinal and transverse heading of a cushion for different speeds and cushion slant. 


Exhibition of cavitations wonder. 


UTILITIES REQUIRED: 


Power Supply 230 V AC, Single Phase. 


Floor space 1m x 1.5 m (approx). 


SAE-40 oil for conveying the test (approx 3 Ltrs.) 


Specialized DETAILS: 


Tilting cushion 


round, square and trapezoidal shapes, one each, with exceptionally cleaned surface and weight recordings. 


Belt 


Unending belt running over wide pulleys, drenched in oil shower. 


Engine Variable speed Motor ½ HP, 1500 RPM. 


Control board For speed control unit. 


Manometer 15 Tube manometer 


Course of action for estimation of sign and hole.

Slip & Creep Measurement Apparatus

TML-0009

This contraption is valuable for estimation of energy transmitted for different information control conditions with shifted belt strain. Belt slip or crawl likewise can be estimated. The mechanical assembly comprises of a variable speed D.C. Engine, driving pulley and driven pulley of equivalent measurements. The pulleys are mounted on input shaft (engine shaft) and yield shaft. The determined pulley can slide on the base just with bearing square to change the underlying strain in belt. Brake drum is mounted on the yield shaft, which measures control yield. The engine speed is changed by Thyristor Control D.C. Drive. A twofold channel computerized speed marker demonstrates driving and driven pulley speeds. With the assistance of Stroboscope (not in the extent of supply) it is conceivable to exhibit the slip of belt on driving and driven pulley. 


Extent OF EXPERIMENTATIONS: 


· To gauge co-productive of contact between pulley material and distinctive belt materials. 


· To gauge control transmitted with fluctuated belt strain. 


· To quantify rate slip at settled belt strain by shifting burden on the Brake drum and plot the diagram of (T1-T2) v/s rate slip i.e. "Slip Characteristics" Finding a Creep Zone from diagram. 


· To quantify belt slip speed and watch the constraining estimation of load at steady speed when the slip just begins. 


· To think about crawl of belt. 


UTILITIES REQUIRED: 


· Electricity o 0.5 kW, 220 V, Single Phase 


· Stroboscope. 


Specialized DETAILS: 


· Motor o Variable speed DC Motor 1HP, 1500 RPM. 


· Pulleys o Driving and driven pulleys of equivalent distances across (level pulleys) 


· Loading Arrangement o Brake drum alongside spring parity and rope plan is given to stack the framework. 


· Belts o Flat belts of settled length of following belt material 


§ Fabric Belt 


§ Canvas Belt 


§ Leather Belt 


· Belt fixing game plan o Bearing square is sliding and dead weight can be connected to set the underlying pressure in belt. 


· Speed Indicator 


2 Channel computerized speed pointer with change to change the channel

Motorised Governor Apparatus

TML-0010

The unit has a base on which bearing holders and driving engine are mounted to end conditions for test shafts i.e. two finishes are settled or one end settled. This mechanical assembly is intended to show the procedure and standards of spinning of shafts with single rotor. As nature of the test is ruinous, thus the unit just exhibits the wonder of spinning shafts. It accompanies 


Determinations: 


1. Test shaft - 4.75 mm, 6.35 mm and 7.9 mm - 2 each. 


2. Drive engine keeps running on 1/8 HP, 1500 rpm with control framework

Supply of Theory of Machines Lab from India to Finland, France, Tanzania, Thailand, Sri Lanka, Congo, Costa Rica, Ivory Coast, Croatia, Cuba, Cyprus, Czech Republic, Denmark, Djibouti, Dominica, Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados, United Arab Emirates (UAE, Dubai), United Kingdom (London), United States, Uruguay, Uzbekistan, Vanuatu, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina Faso, Burma Myanmar, East Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia (Addis Ababa), Fiji, Burundi, Cambodia, Cameroon, Canada, Cape Verde, Central African Republic, Chad, Chile, Colombia. Math Teaching Kit suppliers in Luxembourg, Macedonia, Madagascar, Malawi (Lilongwe), Malaysia (Kuala Lumpur), Maldives, Mali, Malta, Marshall Islands, Mauritania, Mexico, Micronesia, Moldova, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Comoros, Congo. Math Teaching Kit manufacturers in Dominican Republic, Gabon, Gambia, Georgia, Germany, Ghana, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hungary, Iceland, Indonesia, Iran, Iraq, Niger, Nigeria (Abuja), Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines (Manila), Poland, Ireland, Israel, Italy, Jamaica, Japan, Jordan, Kazakhstan, Kenya (Nairobi), Kiribati, Korea, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Mauritius, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Portugal, Qatar, Romania, Russia, Rwanda (Kigali). Math Teaching Kit exportets to Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Sudan, Spain, Sudan, Suriname, Swaziland, Sweden, Switzerland, Syria, Tajikistan, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda (Kampala), Ukraine, Venezuela, Vietnam, Yemen , Zambia (Lusaka), Zimbabwe
'); popupWin.document.close(); }