Quick answer. This is the experiment range for a dynamics of machines laboratory - motorised, instrumented rigs on which a student varies something and measures the result: gyroscope, governors, journal and tilting pad bearings, whirling of shaft, universal vibration, cam analysis, static and dynamic balancing, slip and creep. Codes run TML-0001 upwards across about 110 records. It is not the same range as our demonstration models, which are coded TOM- and listed under models - theory of machines; those show a mechanism moving, these produce a graph. The test to apply to any rig on this page is the one in the next section: what can you vary, and what can you measure while you vary it?
A dynamics apparatus that can only be switched on gives a class one observation. The same apparatus with an independent variable and a measurement chain gives them a graph, a gradient and a comparison with theory - which is the whole point of the laboratory. So before capacity, finish or price, ask what the rig lets you change and what it lets you read. For every experiment in this range there is a specific answer:
| Apparatus | What you vary | What you measure | The result the experiment exists for |
|---|---|---|---|
| Motorised gyroscope (TML-0001) | Applied couple, and spin speed | Rate of precession, spin speed | That precession rate is proportional to the applied couple and inversely proportional to spin - verified, not asserted |
| Universal and motorised governor (TML-0007, TML-0010) | Speed, and sleeve load or spring rate | Sleeve lift against speed | The characteristic curve of each governor type, and the difference between them on one frame |
| Journal bearing (TML-0002) | Load, speed, oil grade and temperature | Pressure at tappings around and along the bearing | The pressure distribution that hydrodynamic theory predicts, and how it collapses as speed falls |
| Michell tilting pad bearing (TML-0008) | Load and speed | Pad tilt and film pressure | Why a pad that is free to tilt forms a converging film at any speed |
| Whirling of shaft (TML-0003) | Speed, shaft diameter and length, end fixing | Amplitude against speed | Critical speed, and how end conditions move it |
| Universal vibration (TML-0004) | Exciting frequency, mass, stiffness, damping | Amplitude and phase against frequency | Resonance, and the effect of damping on the peak - the most transferable result in the subject |
| Cam analysis (TML-0005) | Cam angle, cam and follower type, spring load | Follower displacement, and jump speed | The displacement diagram measured rather than drawn, and the speed at which the follower leaves the cam |
| Static and dynamic balancing (TML-0006) | Mass, radius and angular position of each weight | Residual vibration or reaction at the bearings | That static balance does not imply dynamic balance - the result students remember |
| Slip and creep (TML-0009) | Belt tension and load | Driver and follower speeds | The distinction between slip and creep, which a formula alone never makes clear |
We put this table first because it is the fastest way to tell a well-specified rig from a cheap one. Two rigs can look identical in a photograph and differ entirely in whether the independent variable is adjustable and calibrated. A governor with a fixed spring teaches one curve; a governor with interchangeable springs and a scale on the sleeve teaches the family of curves, which is the syllabus.
Almost every experiment above reduces to one of three measurements, and each has a characteristic failure.
Speed appears in nearly every result on this page, and in the gyroscope and whirling experiments it appears squared or cubed, so an error in speed is magnified in the answer. Specify how speed is measured and insist on a second, independent means of checking it. A contact or optical tachometer reading the shaft directly, cross-checked against the drive setting, is the minimum. Where a stroboscope is used, it must be used with discipline, and a laboratory that owns only a stroboscope and no second instrument will eventually publish a speed that is a simple multiple of the truth.
In the vibration and whirling experiments the quantity of interest is a small displacement of a moving part. Ask what measures it: a dial gauge is useless on a vibrating member, a mechanical drum recorder gives a trace a class can see and measure, and a transducer with a logger gives frequency and phase as well as amplitude. The answer determines which experiments the rig can actually support - phase against frequency, which is where the physics of resonance lives, needs a transducer.
In the gyroscope, balancing and bearing experiments the measured quantity is a force or a reaction. Dead weights on a known arm are simple, honest and visible, and for teaching they are often better than a load cell because the student can see what is applying the couple. Where a load cell is used, ask how it is calibrated and whether a dead-weight check is possible, because an uncalibrated electronic reading is the easiest thing in a laboratory to believe and the hardest to check.
These are motorised rigs with exposed rotating masses, and several of them are deliberately run into a condition the rest of engineering avoids. Three requirements apply to the whole range and should be on the order, not negotiated after delivery:
One practical point about the bearing rigs that nobody mentions until the first session: they leak. Oil on a laboratory floor is the most likely injury in this range. Ask for a drip tray with the rig, decide where waste oil goes before the first experiment, and keep absorbent granules in the room.
Governors are the experiment most often bought wrongly, because the catalogue word "universal" covers several arrangements and a syllabus usually names specific ones. The arrangements a mechanical engineering course normally requires are the simple pendulum type, the loaded type with a central weight, and the spring-loaded type, and what the student is asked to produce is a curve of sleeve lift against speed for each, compared with each other.
So ask three questions: which arrangements can be set up on the frame supplied; is the change-over a conversion the laboratory can do inside a practical session, or a rebuild; and is there a scale on the sleeve, since a lift that has to be estimated by eye produces a scatter plot rather than a curve. For the spring-loaded arrangement, ask whether more than one spring rate is supplied, because the effect of spring stiffness on the governor characteristic is a standard exercise and it cannot be done with one spring.
Related ranges: models - theory of machines for the demonstration models that accompany these experiments, engineering training models for mechanism and linkage models, S.O.M. lab for strength of materials, structural mechanics lab, engineering gear models, and hydraulics and fluid mechanics trainers. The full mechanical lab equipments category lists the rest of this branch.
The models, coded TOM-, show a mechanism moving so that a student can see how it works. The apparatus on this page, coded TML-, is instrumented so that a student can vary a quantity and measure the consequence. A laboratory teaching the subject properly wants both: the model makes the mechanism intelligible, and the rig turns it into a measurement. If your budget covers only one, buy according to what your assessment requires - a laboratory report needs data, a lecture needs a model.
Because it produces the result students find least intuitive: an assembly can be perfectly balanced at rest and shake violently when it rotates. Static balance requires the resultant force to vanish; dynamic balance also requires the resultant couple to vanish, and two equal masses set at opposite ends of a shaft and 180 degrees apart satisfy the first and fail the second. Measuring the bearing reaction makes that unavoidable, which is why it belongs in a laboratory rather than a lecture.
It is the one experiment in the laboratory where the machine is deliberately run at its own critical speed, so the amplitude grows while the student watches. That is exactly why it teaches well, and exactly why the guard, the anchorage, the stated maximum speed and a drive limited to it are not optional. Ask us for the maximum speed in writing and make it part of the standing instruction for that rig.
You can take readings, but they will not be comparable from one session to the next. Oil viscosity falls steeply with temperature and viscosity is in the theory, so the oil grade and the oil temperature are part of the result and belong on the report form. If the rig has no temperature measurement, add one; if the laboratory is hot in the afternoons, expect the morning and afternoon groups to disagree until the temperature is recorded.
Ask per item and get the answer in writing before ordering. For a teaching laboratory the manual - the procedure, the theory, the observation table and a worked example - is a substantial part of the value, and it is the thing most often missing. If a manual is not supplied, budget staff time to write one, because a rig without a procedure tends to sit unused after the member of staff who understood it moves on.
Sometimes, and it can be a false economy. A universal vibration frame genuinely supports many experiments and is good value. A single frame that must be rebuilt between experiments costs session time every week for the life of the rig, and in a laboratory with six groups rotating it becomes the bottleneck. Tell us your session length and group count and we will say which combination is sensible rather than which is cheapest.
Ray Export is a manufacturer and exporter of laboratory, scientific and educational equipment based at Plot No. 449, HSIIDC Industrial Area, Saha, Ambala, Haryana 133104, India. Enquiries: [email protected], +91-9817319615.
Written by Palak Mall, Senior Content Writer. Technically reviewed by Arvind Kumar, Lab Equipment Specialist, 12+ years in laboratory and testing instrumentation. Last updated: 17 October 2026.
Notes on this listing, published rather than hidden: the tilting pad bearing is named after A.G.M. Michell and the record spells it "Michel" - we are correcting it, and we print the correct spelling here because it is the word a specifier will search for. One record ("Cam Analysis Apparatus-") carries a stray trailing hyphen in its name. This category covers the same subject as our TOM- coded models range under a different parent; the two hold different products with different codes, and we have recommended that the relationship between them be made explicit in the site structure rather than left for a visitor to work out. Specifications are confirmed in writing on the quotation; for certificates and standards, contact us for the latest copies of the relevant certificates before tender submission.
Highlights Low cost, successful educating. Independent. Seat mounted. A few rigging train. Single or twofold buy lift. Assurance of mechanical favorable position, speed proportion and constraining proficiency. Three year guarantee.
Highlights Low cost, powerful showing Self-contained Wall mounted Introduction to straightforward machines Determination of speed proportion mechanical favorable position and effectiveness Comparative proficiency of square and Vee frame strings Three year guarantee Range of Experiments Experimental assurance of speed proportion and correlation with computed esteem Determination of variety with heap of: exertion grinding productivity Limiting proficiency of the machine Comparison of relative productivity of Vee and Square string shapes Description The test screw jack system is based on a tough divider section The pole of the 200mm measurement turntable has both square and Vee shape strings of 24mm x 3mm pitch. The heap holder can be suspended from a burden from both of the nuts. Torque is connected to the turntable through two "effort" holders, and can be orchestrated to either lift or lower the heap. This gear is a piece of a range intended to both exhibit and tentatively affirm fundamental designing standards. Extraordinary care has been given to every thing in order to give wide trial scope without unduly confusing or trading off the outline. Each bit of mechanical assembly is independent and minimized. Setting up time is insignificant, and all estimations are made with the most straightforward conceivable instrumentation, so the understudy contribution is absolutely with the designing standards being educated. A total guideline manual is given depicting the mechanical assembly, its application, exploratory technique and run of the mill test comes about.
Highlights Low cost, powerful showing Aids comprehension of gyroscopic precession through "hands on" contribution High visual effect Three year guarantee Range of Experiments To exhibit outwardly precession and steadiness of a spinner, and to evaluate the impact of heading of turn and speed of revolution Description HTM15 is a model whirligig which is put into movement by pulling a line wrapped around its pole. It can be mounted on a counter weighted arm, remained on a vertical pointed section, or on a slanting wire. All essential gyroscopic wonders can be exhibited convincingly with this straightforward gear. This hardware is a piece of a range intended to both show and tentatively affirm essential building standards. Extraordinary care has been given to every thing to give wide exploratory extension without unduly confounding or bargaining the plan. Each bit of mechanical assembly is independent and smaller. Setting up time is insignificant, and all estimations are made with the easiest conceivable instrumentation, so the understudy inclusion is absolutely with the designing standards being instructed. An entire guideline manual is given depicting the mechanical assembly, its application, exploratory methodology and run of the mill test comes about.
Coriolis Component of Acceleration Our noticeable quality in this space mastery has helped us think of Coriolis Component of Acceleration.. This whole set up is intended to ponder different corioli's parts of a slider wrench instrument. In this procedure the persistent stream of water which is moving through an unfaltering turning pair of tubes replaces mechanical slider framework. The containers of the framework can be effortlessly turned in different velocities with the utilization of a swinging field engine which likewise serves a dynamometer. There is a Perspex window situated on the highest point of the tank. This window guarantees finish clear perspective of the procedure. It additionally keeps the sprinkling of water over the side of the tank. The in-fabricated dynamometer consistently measures the torque which is connected to the different turning tubes. This whole gear is independent. The re-coursing of the water is helped with a claim speed control unit and water flowing pump which is isolated. Extent Of Experimentations: To decide Corioli's Component of Acceleration at different velocities of revolution and water stream rates Utilities Required: Electricity 0.5 kW, 220 V, Single Phase Drain Water Supply Technical Details: Swinging field write, variable speed Pump FHP The entire set-up is all around planned and masterminded in a decent quality painted structure Fabricated out of stainless steel Rotating arms 9mm/6mm opening distance across, length 300 mm Rotameter 250 to 2500 LPH Electric engine Main tank Control Panel involves: Speed control unit Standard make On/Off switch, mains marker RPM pointer with nearness sensor RPM estimation Theory of Machine Lab Apparatus lab hardware manufacturers,exporters and Theory of Machine Lab Apparatus Lab providers
Highlights Low cost, compelling showing Self-contained Wall mounted Introduction to basic machines Determination of speed proportion mechanical favorable position and effectiveness Three year guarantee Range of Experiments Experimental assurance of speed proportion and examination with figured esteem Determination of variety with heap of: exertion contact proficiency Limiting productivity of the machine Description This fantastic case of a steel worm and phosphor bronze wheel is based on a considerable divider mounted base. Both worm and wheel have fundamental rope drums with ropes and load holders to give torque. The speed proportion of 30:1 is accomplished by a solitary begin worm. This hardware is a piece of a range intended to both show and tentatively affirm essential designing standards. Incredible care has been given to every thing in order to give wide exploratory degree without unduly confounding or bargaining the plan. Each bit of mechanical assembly is independent and minimized. Setting up time is negligible, and all estimations are made with the easiest conceivable instrumentation, so the understudy association is simply with the building standards being instructed. A total guideline manual is given portraying the contraption, its application, exploratory methodology and run of the mill test comes about..
Highlights Low cost, compelling educating. Independent. Seat mounted. A few apparatus prepare. Single or twofold buy lift. Assurance of mechanical preferred standpoint, speed proportion and restricting effectiveness. Three year guarantee..
Highlights Low cost, compelling showing Self-contained Wall mounted Demonstrates: a) Second Law of Motion b) Energy stockpiling Three year guarantee Range of Experiments To check the second law of movement connected to a flywheel, ie the connection amongst torque and rakish accerleration To think about test and figured snapshots of idleness of a plate To ponder the vitality changes and to exhibit that a flywheel can be utilized to store vitality Description A steel circle 250 mm distance across and 30 mm thick is mounted on a pole running in metal rollers housed on a considerable divider section. A blemish on the flywheel and a pointer on the section empower the insurgencies to be checked and planned with the stop watch provided. A line, stack holder and set of weights are given. This gear is a piece of a range intended to both exhibit and tentatively affirm fundamental building standards. Extraordinary care has been given to every thing in order to give wide test scope without unduly muddling or bargaining the plan. Each bit of mechanical assembly is independent and smaller. Setting up time is negligible, and all estimations are made with the least difficult conceivable instrumentation, so the understudy association is absolutely with the designing standards being instructed. An entire direction manual is given portraying the device, its application, exploratory system and commonplace test outcomes..
Highlights Low cost, compelling showing Self-contained Bench mounted Measurement of wrench edge and slider position Conventional slider wrench instrument Velocity and quickening by graphical differentation Variable wrench length Variable interfacing pole length Three year guarantee Range of Experiments To decide the connection between wrench point and stroke To examine the impact of changing the a) wrench sweep b) associating bar length To research by graphical differentation the connection amongst rakish and direct speeds and increasing speeds of the system To build speed and quickening outlines for the component Comparison of trial comes about with hypothetical expectations Description The contraption demonstrates the connection between wrench shaft revolution and cylinder dislodging, for a settled "cylinder". The wrench length is flexible, and the interfacing pole length can be changed. Crankshaft turn is estimated by a pivoting protractor scale and cylinder uprooting is appeared on a sliding scale. The gear might be mounted vertically for exhibition purposes, or level on the seat for exploratory utilize. This hardware is a piece of a range intended to both exhibit and tentatively affirm fundamental building standards. Incredible care has been given to every thing to give wide exploratory degree without unduly muddling or bargaining the plan. Each bit of device is independent and smaller. Setting up time is insignificant, and all estimations are made with the least difficult conceivable instrumentation, so the understudy contribution is simply with the designing standards being instructed. A total guideline manual is given depicting the device, its application, trial method and normal test outcomes..
Sun based Gear Apparatus - Engineering Lab Training Systems Many in cooler atmospheres with less sun oriented vitality accessible have worries about changing to sun based fountains. These frameworks can in any case spare vitality and cash for this gathering since they can be utilized as a part of conjunction with gas or electric water radiators. A backhanded dissemination framework is best for these atmospheres. Changing to the sunlight based fountains amid the mid year and sunnier days of spring and fall can spare shoppers a great deal of vitality since sun powered power costs nothing. It likewise gives true serenity that, since sun oriented power doesn?t emit nursery emanations that nature is being ensured. Another liven to utilizing sun powered fountains is that amid control blackouts it kicks in to full apparatus for shopper comfort..
Highlights Low cost, successful instructing. Independent. Divider mounted. Prologue to straightforward machines. . Assurance of speed proportion mechanical favorable position and proficiency. Three year guarantee. Scope of Experiments Experimental assurance of speed proportion and correlation with figured esteem. Assurance of variety with heap of exertion effectiveness Description The PVC double distance across wheel has a hub bolstered on basic turns in a tough divider mounting section. Lines twisted round the peripheries of the wheels convey stack holders for the heap and exertion. An arrangement of weights is given. This hardware is a piece of a range intended to both show and tentatively affirm essential building standards. Awesome care has been given to every thing in order to give wide trial scope without unduly convoluting or trading off the outline. Each bit of device is independent and conservative. Setting up time is negligible, and all estimations are made with the least complex conceivable instrumentation, so the understudy inclusion is absolutely with the building standards being educated. An entire guideline manual is given portraying the contraption, its application, exploratory methodology and run of the mill test comes about.